Satec EM132 User manual

BG0491 REV. A12
EM13x Series
SMART MULTIFUNCTION METER
Installation and Operation Manual

2EM13x Series SMART MULTIFUNCTION METER
LIMITED WARRANTY
The manufacturer offers the customer a 24-month functional warranty on
the instrument for faulty workmanship or parts from date of dispatch from
the distributor. In all cases, this warranty is valid for 36 months from the
date of production. This warranty is on a return to factory basis.
The manufacturer does not accept liability for any damage caused by
instrument malfunction. The manufacturer accepts no responsibility for
the suitability of the instrument to the application for which it was
purchased.
Failure to install, set up or operate the instrument according to the
instructions herein will void the warranty.
Only a duly authorized representative of the manufacturer may open your
instrument. The unit should only be opened in a fully anti-static
environment. Failure to do so may damage the electronic components and
will void the warranty.
The greatest care has been taken to manufacture and calibrate your
instrument. However, these instructions do not cover all possible
contingencies that may arise during installation, operation or
maintenance, and all details and variations of this equipment are not
covered by these instructions.
If the equipment is used in a manner not specified by SATEC LTD, the
protection provided by the equipment may be impaired.
For additional information regarding installation, operation or maintenance
of this instrument, contact the manufacturer or your local representative
or distributor.
All trademarks are property of their respective owners.
Copyright 2007-2017 SATEC LTD.

EM13x Series SMART MULTIFUNCTION METER 3
WARNING
Read the instructions in this manual before performing installation and take note of the
following precautions:
1. Ensure that all incoming AC power and other power sources are turned OFF before performing
any work on the instrument. Protect the measurement AC Inputs voltage (V1, V2, V3) with 2A
external overcurrent protection device and the power supply source inputs with 5A external
overcurrent protection device, located close to the equipment.
2. Before connecting the instrument to the power source, check the labels on the back of the
instrument to ensure that your instrument is equipped with the appropriate power supply
voltage, input voltages and currents. Failure to do so may result in serious or even fatal injury
and/or equipment damage.
3. Under no circumstances should the instrument be connected to a power source if it is damaged.
4. To prevent potential fire or shock hazard, do not expose the instrument to rain or moisture.
5. The secondary of an external current transformer must never be allowed to be open circuit
when the primary is energized. An open circuit can cause high voltages, possibly resulting in
equipment damage, fire and even serious or fatal injury. Ensure that the current transformer
wiring is secured using an external strain relief to reduce mechanical strain on the screw
terminals, if necessary.
6. Only qualified personnel familiar with the instrument and its associated electrical equipment
must perform setup procedures.
7. Do not open the instrument under any circumstances when it is connected to a power source.
8. Do not use the instrument for primary protection functions where failure of the device can cause
fire, injury or death. The instrument can only be used for secondary protection if needed.
Read this manual thoroughly before connecting the device to the current carrying
circuits. During operation of the device, hazardous voltages are present on input
terminals. Failure to observe precautions can result in serious or even fatal injury or
damage to equipment.
This equipment does not require cleaning for proper operation

4EM13x Series SMART MULTIFUNCTION METER
Quick Start Guide
This section can be used by a licensed electrician to install and perform
basic EM13X setup. For more detailed EM13X Series setup and use
instructions, see the following chapters in this manual.
This quick start guide will assist you to have the unit running for the first
time.
During the operation of the meter, hazardous voltages are present in the
input terminals. Failure to observe precautions can result in serious or
even fatal injury or damage to equipment.
For complete and accurate in-depth instructions, refer to the following
chapters in this manual.
Installing the EM13X SERIES
Mounting the EM13X SERIES Unit
To mount the EM13X SERIES on Din rail:
Hang the EM13X Series unit on the DIN Rail by positioning the upper side
first then lower side.
Push up the DIN rail brackets to lock the EM13X Series on the rail.
Mounting the EM13X Series on DIN-Rail

EM13x Series SMART MULTIFUNCTION METER 5
To mount the EM13X Series on flat surface:
Locate the EM13X Series on the surface to
Push up the DIN rail brackets to lock the EM13X Series on the rail.
Connecting the EM13X Series Unit
Ensure that all incoming power sources are OFF.
Check that you have the appropriate power supply.
For direct connection, connect to CT wires through the meter CT
terminals. Observe the arrow that indicates the current direction.
In case of a retrofit application or high current external SATEC CT (or
Split Core) where each external CT ends with two wires:
Connect the wire to the meter current termination
screws.
Connect the measured voltage inputs
Connect COM1 –RS-485 communication port
In case of EM132/133 model with Aux. Power supply connect the Power
Supply inputs using 1.5 mm2/14AWG-dedicated wires.
Common Wiring Mode: EM13x and EM13x-SE 4LL3 or 4Ln3
EM13x-SE: Self Energized Meter model

6EM13x Series SMART MULTIFUNCTION METER
CT wiring
To connect an Option module:
Assemble the module on the meter.
Power the EM13X Series unit on.
Assembly a small module

EM13x Series SMART MULTIFUNCTION METER 7
Assembling the 12DI/4RO module
To operate the EM13X Series:
Perform device diagnostics.
Configure the device through the EM13X Series unit front panel display
Configuring the EM13X Series remotely
Install the PAS application software on your PC.
Configure the PAS database for your meter.
Configure the PAS communications settings.
Upgrade the meter firmware if a new version is available.
Set up the meter using the PAS application software.
Configure your security settings through the meter security setup.
Configure your communication protocol settings.
Configure Billing/TOU registers.
At this stage, the EM13X Series should be ready for operation.

Chapter 1 General Information Features
8EM13x Series SMART MULTIFUNCTION METER
Table of Contents
Chapter 1 General Information ..........................................................................11
1.1 Features.......................................................................................................................13
1.2 Available Options.......................................................................................................14
Digital I/O ............................................................................................................ 15
Analog Output ...................................................................................................... 15
Additional Communication Port–COM2.................................................................... 15
1.3 Customized Options..................................................................................................16
Device Resolution.................................................................................................. 16
Display Options..................................................................................................... 16
1.4 Measured Parameters ..............................................................................................17
1.5 Labelling......................................................................................................................19
Chapter 2 Installation ..........................................................................................20
2.1 Site Requirements.....................................................................................................20
2.2 Package Contents......................................................................................................20
2.3 Mechanical Installation.............................................................................................20
Wall Mounting....................................................................................................... 22
DIN Rail Mounting ................................................................................................. 23
Add-On Module Mounting....................................................................................... 24
2.4 Electrical Installation.................................................................................................25
Connecting the wires ............................................................................................. 25
Typical Installation ................................................................................................ 26
Terminals............................................................................................................. 31
Power Source Connection....................................................................................... 32
Voltage Input connection ....................................................................................... 34
Current Input Connection....................................................................................... 35
Wiring Diagrams ................................................................................................... 36
2.5 Battery Replacement................................................................................................43
2.6 I/O Connections ........................................................................................................44
2DI/1RO Standard ................................................................................................ 44
4DI/2RO Module ................................................................................................... 45
8 DI module......................................................................................................... 46
12DI/4RO Module ................................................................................................. 46
4AO Module - Analog Outputs................................................................................. 47
2.7 Communications Connections.................................................................................49
RS-485 Connection ............................................................................................... 50
ETH module –COM2 Ethernet Connection................................................................ 51
PRO module –COM2 PROFIBUS Connection............................................................. 52
CANopen module –COM2 CANopen Connection ....................................................... 53
RS-232/422-485 module –COM2 Connection .......................................................... 53
Connecting a GSM/GPRS/3G module....................................................................... 54
Connecting an RF module ...................................................................................... 55
Chapter 3 Using Front Display............................................................................56
Energy Pulse LED.................................................................................................. 56
COMPort Activity LEDs........................................................................................... 56
VOLTAGES LEDs ................................................................................................... 56
Navigation Buttons................................................................................................ 56
3.1 Display Operations ....................................................................................................57
Navigation Buttons................................................................................................ 57

Chapter 1 General Information Features
EM13x Series SMART MULTIFUNCTION METER 9
Navigating in Data Display Mode............................................................................. 58
Display Features ................................................................................................... 58
Measurement Units ............................................................................................... 59
3.2 Data Displays..............................................................................................................59
TEST Mode Data Display ........................................................................................ 59
Billing Period Energy Data Displays ......................................................................... 59
TOU/Maximum Demand Power Data Display............................................................ 61
Instrumentation Measurement Maximum Demand Data Display................................. 63
Instrumentation Measurement................................................................................ 64
Status Inputs and Outputs ..................................................................................... 66
Device Info Display ............................................................................................... 67
3.3 Programming Mode..................................................................................................69
Navigation Buttons................................................................................................ 69
Entering Numeric Values........................................................................................ 69
Password Security................................................................................................. 69
Setup Menus and Access Rights.............................................................................. 69
Viewing and Changing Setup Options ...................................................................... 71
Chapter 4 Using PAS Software...........................................................................72
4.1 Installing PAS.............................................................................................................72
4.2 Creating a New Site for your Meter........................................................................72
Chapter 5 Configuring the EM13X Series..........................................................74
5.1 Configuring Communications..................................................................................74
Setting Up Serial Communication Ports.................................................................... 74
Setting up the Ethernet.......................................................................................... 76
Setting up GPRS Network ...................................................................................... 77
Setting Up eXpertPower Client................................................................................ 78
Setting Up TCP Notification Client............................................................................ 79
5.2 General Meter Setup .................................................................................................80
Basic Meter Setup ................................................................................................. 80
Device Options ..................................................................................................... 83
Configuring Digital Inputs....................................................................................... 84
Configuring Relay Outputs...................................................................................... 86
Configuring Analog Outputs.................................................................................... 89
Configuring Counters............................................................................................. 91
Configuring Alarm/Control Setpoints........................................................................ 93
Configuring the Display.......................................................................................... 96
Local Time Settings ............................................................................................... 98
5.3 Configuring Meter Security................................................................................... 100
5.4 Configuring Billing/TOU........................................................................................ 102
Configuring Billing/Tariff Registers......................................................................... 102
Configuring the Daily Tariff Schedule ..................................................................... 104
Configuring the Season Tariff Schedule.................................................................. 105
5.5 Configuring Recorders........................................................................................... 106
Configuring Meter Memory................................................................................... 106
Configuring the Event Recorder ............................................................................ 108
Configuring the Data Recorder.............................................................................. 108
5.6 Configuring Communication Protocols............................................................... 111
Configuring Modbus............................................................................................. 111
Configuring DNP3................................................................................................ 112
Chapter 6 Device Control and Upgrading....................................................... 115
6.1 Resetting Accumulators, Maximum Values and Files...................................... 115
6.2 Updating the Meter Clock...................................................................................... 117

Chapter 1 General Information Features
10 EM13x Series SMART MULTIFUNCTION METER
6.3 Viewing and Clearing Device Diagnostics.......................................................... 118
6.4 Viewing Communication Status and Statistics.................................................. 118
6.5 Remote Relay Control............................................................................................ 119
6.6Upgrading Device Firmware................................................................................. 120
Chapter 7 Monitoring Meters ........................................................................... 122
7.1 Viewing Real-time Data......................................................................................... 122
7.2 Viewing Real-time Min/Max Log......................................................................... 125
7.3 Viewing Real-time Waveforms............................................................................ 125
7.4 Viewing Real-time Harmonic Spectrum............................................................. 127
Chapter 8 Retrieving and Storing Files........................................................... 131
8.1 Uploading Files on Demand.................................................................................. 131
8.2 Using the Upload Scheduler.................................................................................. 132
8.3 Viewing Files On-line.............................................................................................. 134
8.4 Exporting Files......................................................................................................... 134
Exporting Files in COMTRADE and PQDIF Formats................................................... 134
Exporting Files in Excel Format ............................................................................. 135
8.5 Archiving Files ......................................................................................................... 136
Chapter 9 Viewing Files .................................................................................... 137
9.1 Operations with Files ............................................................................................. 137
9.2 Viewing Options...................................................................................................... 137
Customizing Views .............................................................................................. 137
Working with Tables............................................................................................ 138
Working with Graphic Windows............................................................................. 138
9.3 Viewing the Event Log........................................................................................... 140
9.4 Viewing the Data Log............................................................................................. 141
Appendix A Technical Specifications .............................................................. 143
Appendix B Standards Compliance................................................................. 149
Appendix C Analog Output Parameters ......................................................... 152
Appendix D Setpoint Triggers and Actions.................................................... 154
Appendix E Parameters for Data Monitoring and Logging.......................... 157
Appendix F Billing/TOU Profile Log File ......................................................... 166
Appendix G Data Scales.................................................................................... 168
Appendix H Device Diagnostic Codes............................................................. 169

Chapter 1 General Information Features
EM13x Series SMART MULTIFUNCTION METER 11
Chapter 1 General Information
The EM13X Series is a compact, multi-function, three-phase AC
Powermeter specially designed to meet the requirements of users
ranging from electrical panel builders to substation operators.

The EM13X Series measuring and power supply inputs comply with
Measuring Category III
The EM13X Series offers standard voltage, current, power and
frequency measurements, amp-demand, energy measurements and
data logging, harmonic analysis and control capabilities.
The EM13X Series consists of three different models series:
EM132/EM133 with AC/DC Auxiliary Power Supply (40-318V AC/DC)
‒EM132/EM133-5, internal CT, transformer operated
configuration with current inputs: In = 5A, Imax = 10A
‒EM132/EM133-1, internal CT, transformer operated
configuration with current inputs: In = 1A, Imax = 2A
‒EM132/EM133-RS5, external CT, transformer operated
configuration with current inputs (secondary current): In =
2.mA, Imax = 5mA
‒EM132/EM133-50, internal CT, direct connection
configuration with current inputs: In = 50A, Imax = 63A
‒EM132/EM133-HACS, external CT, direct connection
configuration with current inputs (secondary current): In =
20mA, Imax = 40mA
EM133-SE –self energized device with 3 Phase Power Supply,
operating from any combination of the measured phases
‒EM133-SE-5, internal CT, transformer operated configuration
with current inputs: In = 5A, Imax = 10A
‒EM133-SE-1, internal CT, transformer operated configuration
with current inputs: In = 1A, Imax = 2A
‒EM133-SE-RS5, external CT, transformer operated
configuration with current inputs (secondary current): In =
2.mA, Imax = 5mA
‒EM133-SE-50, internal CT, direct connection configuration
with current inputs: In = 50A, Imax = 63A

Chapter 1 General Information Features
12 EM13x Series SMART MULTIFUNCTION METER
‒EM133-SE-HACS, external CT, direct connection
configuration with current inputs (secondary current): In =
20mA, Imax = 40mA
EM132/EM133-21DC with DC Auxiliary Power Supply (9-36 VDC)
‒EM132/EM133-21DC-5, internal CT, transformer operated
configuration with current inputs: In = 5A, Imax = 10A
‒EM132/EM133-21DC-1, internal CT, transformer operated
configuration with current inputs: In = 1A, Imax = 2A
‒EM132/EM133-21DC-RS5, external CT, transformer operated
configuration with current inputs (secondary current): In =
2.mA, Imax = 5mA
‒EM132/EM133-21DC-50, internal CT, direct connection
configuration with current inputs: In = 50A, Imax = 63A
‒EM132/EM133-21DC-HACS, external CT, direct connection
configuration with current inputs (secondary current): In =
20mA, Imax = 40mA
All models series include the following units:
2 lines of 16 characters LCD display.
A standard RS-485 communication port, Infra-Red Communication
port and an additional optional Ethernet, Profibus or RS-232/RS-
422/RS-485 or RF Modem port. These ports allow local and remote
automatic meter readings and setup through the supplemental
communication or user data acquisition software
Different communication options for remote communications with the
meter. These options enable LAN and Internet communication with
the unit.
Two digital inputs with 10-ms scan time and one relay output with 1-
cycle update time
The EM13X Series is suitable for mounting on both standard DIN-Rail
and wall-mount.

Chapter 1 General Information Features
EM13x Series SMART MULTIFUNCTION METER 13
1.1 Features
Multifunctional 3-phase Power Meter
3 voltage inputs and 3 current transformer-isolated AC inputs for
direct connection to power line or via potential and current
transformers
True RMS, volts, amps, power, power factor, neutral current, voltage
and current unbalance, frequency
Ampere/Volt demand meter
25/50/60/400
1
Hz measurement capabilities
Billing/TOU Energy Meter
IEC 62053-22 Class 0.5S /ANSI C12.20 Acc. Class 0.5, four-quadrant
active and reactive energy polyphase static meter
Three-phase total and per phase energy measurements; active,
reactive and apparent energy counters
Time-of-Use, 4 totalization and tariff energy/demand registers x 8
tariffs, 4 seasons x 4 types of days, 8 tariff changes per day,
One–time easy programmable tariff calendar schedule
Automatic daily energy and maximum demand profile log for total
and tariff registers
Voltage and current THD, current TDD and K-Factor, up to 40th
order harmonic
Voltage and current harmonic spectrum and angles
Real-time Waveform Capture
Real-time “scope mode” waveform monitoring capability
Simultaneous 6-channel one-cycle waveform capture at a rate of 64
samples per cycle
Programmable Logical Controller
Embedded programmable controller
16 control setpoints; programmable thresholds and delays
Relay output control
1-cycle response time
Non-volatile memory for long-term event and data recording
Event recorder for logging internal diagnostic events and setup
changes
Two data recorders; programmable data logs on a periodic basis;
automatic daily energy and maximum demand profile log
Digital I/O
2 digital inputs (standard) and four to twelve digital inputs (optional)
with 1/2 cycle scan time; automatic recording of last five digital input
1
25Hz and 400Hz options are available only with internal CT.

Chapter 1 General Information Available Options
14 EM13x Series SMART MULTIFUNCTION METER
change events with timestamps (see the EM13X Series MODBUS
Reference Guide)
1 relay output (standard) and two to four relay outputs (optional)
with 1-cycle update time; unlatched, latched, pulse and KYZ
operation; energy pulses
Display
Easy to read 2x16 characters LCD display, adjustable update time
Auto-scroll option with adjustable page exposition time; auto-return
to a default page
Programmable display auto-scroll sequence
Communications
Standard 2-wire RS-485 communication port; MODBUS RTU, DNP3,
SATEC ASCII and IEC 60870-5-101 communication protocols
Optional second communication port; MODBUS RTU, MODBUS/TCP,
DNP3, DNP3/TCP, SATEC ASCII, PROFIBUS DP, CANopen and IEC
60870-5-104 (over TCP) communication protocols
eXpertPowerclient for communicating with the SATEC proprietary
eXpertPowerInternet services (with the Ethernet/GPRS module)
TCP notification client for communicating with a remote
MODBUS/TCP server on events or periodically on a time basis (with
the Ethernet/GPRS module)
Meter Security
Password security for protecting meter setups and accumulated data
from unauthorized changes
Upgradeable Firmware
Easy upgrading device firmware through a serial or Ethernet port.
Software Support
PAS™–meter configuration and data acquisition SATEC Software
tool
eXpertPower™ –SATEC proprietary Internet services
1.2 Available Options
The EM13X Series can be provided with an optional expansion module
from the following list:
Digital I/O
Analog outputs
Ethernet communication port
PROFIBUS DP communication port
CANopen communication port
RS-232/RS-422/RS-485 communication port
Cellular communication port based on ENFORA GPRS or TELIT 3G or
4G engine
RF communication port

Chapter 1 General Information Available Options
EM13x Series SMART MULTIFUNCTION METER 15
Digital I/O
The EM13X Series digital I/O expansion module provides:
4DI/2RO Module
4dry contact digital inputs (DI) for monitoring external contacts and
receiving pulses from energy, water, and gas meters; Programmable
de-bounce time; 1-ms scan time.
2 electro-mechanical or solid-state relay outputs (RO) for alarms and
controls, and for output energy pulses; unlatched, latched and pulse
operations, failsafe operation for alarm notifications; programmable
pulse width; direct remote relay control through communications; 1-
cycle update time.
8DI module
8 dry contact digital inputs (DI) for monitoring external contacts and
receiving pulses from energy, water, and gas meters
Programmable de-bounce time; 1-ms scan time.
12DI/4RO Module
12 dry contact digital inputs (DI) for monitoring external contacts
and receiving pulses from energy, water, and gas meters;
Programmable de-bounce time; 1-ms scan time.
4 electro-mechanical relay outputs (RO) for alarms and controls, and
for output energy pulses; unlatched, latched and pulse operations,
failsafe operation for alarm notifications; programmable pulse width;
direct remote relay control through communications; 1-cycle update
time.
Analog Output
The EM13X Series analog output (AO) expansion module provides:
4 optically isolated analog outputs with an internal power supply;
Options for 0-20mA, 4-20mA, 0-1mA, and 1mA output; 1-cycle
update time.
Additional Communication Port–COM2
A second COM2 communication port can be ordered as an expansion
module. COM2 options available:
Ethernet 10/100BaseT port; MODBUS/TCP, DNP3/TCP or IEC 60870-
5-104 communications protocols
PROFIBUS DP port
CANopen port
RS-232/RS-422/RS-485 port; MODBUS RTU, DNP3 or IEC 60870-5-
101, and SATEC ASCII communication protocols;
GPRS or 3G/4G cellular communications port; MODBUS/TCP protocol
RF communication; MODBUS RTU protocol

Chapter 1 General Information Customized Options
16 EM13x Series SMART MULTIFUNCTION METER
1.3 Customized Options
Presentation of data on the front display and via communications can
be customized to best suit the user application.
Device Resolution
A low or high-resolution option can be selected for the presentation of
voltage, current, and power for use in high and low power applications.
Display Options
Different display options are available for customization to be used in
dark or non-safe locations, or in places that are hardly accessible for
observation.

Chapter 1 General Information Measured Parameters
EM13x Series SMART MULTIFUNCTION METER 17
1.4 Measured Parameters
Table 1: Measured and Displayed Parameters
Parameter
Display
Comm.
Analog
Pulse
Alarm
1-cycle Real-time Measurements
RMS Voltage per phase



RMS Current per phase



kW per phase


kvar per phase


kVA per phase


Power Factor per phase


Total kW



Total kvar



Total kVA



Frequency



Neutral Current



Total Power Factor



Voltage & Current unbalance


1-sec Average Measurements
RMS Voltage per phase




RMS Current per phase




kW per phase



kvar per phase



kVA per phase



Power Factor per phase



Total kW




Total kvar




Total kVA




Total Power Factor




Frequency




Neutral Current




Voltage & Current unbalance



Amps & Volt Demands
Ampere & Volt Demand per phase


Ampere Maximum Demand per phase



Voltage Maximum Demand per phase



Power Demands
kW Accumulated Demand Import & Export



kvar Accumulated Demand Import & Export



kVA Accumulated Demand



kW Demand Import & Export


kvar Demand Import & Export


kVA Demand


kW Sliding Demand Import & Export


kvar Sliding Demand Import & Export


kVA Sliding Demand


kW Predicted Demand Import & Export


kvar Predicted Demand Import & Export


kVA Predicted Demand


kW Maximum Demand Import


kW Maximum Demand Export



Chapter 1 General Information
18 EM13x Series SMART MULTIFUNCTION METER
Parameter
Display
Comm.
Analog
Pulse
Alarm
kvar Maximum Demand Import


kvar Maximum Demand Export

kVA Maximum Demand


Total Energy
Total kWh Import & Export



Total kvarh Import & Export



Total kvarh Net

Total kVAh



Energy per Phase
kWh Import per phase


kvarh Import per phase

kVAh per phase


TOU Registers
4 TOU energy registers (kWh and kvarh
import & export, kVAh, 4 pulse sources)


4 TOU maximum demand registers

8 tariffs, 4 seasons x 4 types of day



Harmonic MeasurementsEH
Voltage THD per phase




Current THD per phase




Current TDD per phase




K-factor per phase




Voltage harmonics per phase up to order 40


Current harmonics per phase up to order 40


Voltage harmonic angles up to order 40

Current harmonic angles up to order 40

Fundamental Component
Voltage and Current per phase

kW, PF per phase


kvar, KVA per phase


Total kW, PF


Total kvar, KVA


Min/Max Logging
Min/Max A, V, total kW, kvar, kVA, PF


Min/Max Frequency, Neutral current


Phase Rotation



Voltage and Current Phase Angles


Day and Time


Pulse Counters



Digital Inputs (optional)



Relay Outputs (optional)



Remote Relay Control (optional)

Alarm Triggers/Setpoints


Self-diagnostics



Chapter 1 General Information Labelling
EM13x Series SMART MULTIFUNCTION METER 19
1.5 Labelling
Figure 1-1 EM133 label –UL marking
Figure 1-2 EM133 label –NMI marking
Figure 1-3 EM133 label –CE MID marking

Chapter 2 Installation Site Requirements
20 EM13x Series SMART MULTIFUNCTION METER
Chapter 2 Installation
This chapter discusses the following types of physical installations for
the EM13X Series SMART MULTIFUNCTION METER:
Mechanical Installation
Electrical Installation
I/O Connections
COM Port Connections.
2.1 Site Requirements
Environmental conditions: as specified in Technical Specifications in
Appendix A
Electrical requirements: as specified in Technical Specifications in
Appendix A
See Technical Specifications in Appendix A for more details
2.2 Package Contents
The EM13X Series SMART MULTIFUNCTION METER package contains
the following items:
EM13X Series SMART MULTIFUNCTION METER unit
Technical Documentation CD
EM13X Series Quick Start guide
2.3 Mechanical Installation
Refer to the figures provided in this section to properly perform the
mechanical installation.