Satec PM130 PLUS Instruction manual

BG0441 REV.A9 ENGLISH PM130 PLUS QuickStart www.satec-global.com
PM130 PLUS Quick Start Manual
This Quick Start Manual is a short guide on how to mount, connect, configure and operate the
PM130 PLUS. It is not intended to replace reading the full User Manual –and particularly the
safety precautions. The manual is available on the Product Documentation CD.
Mounting, electrical connection and settings of the PM130 shall be made in
accordance with all applicable laws and/or regulations and be performed by
authorized personnel only.
MOUNTING
Position the PM130 meter in 92×92mm square or 4” round cutout (Figure 1). If two PM130 are
positioned side by side, keep at least 150mm (5.9”) between their centers to allow installation
of add-on modules (140mm/5.5” if only small form modules will be used).
Attach the PM130 unit using washers and nuts. Make sure that the unit is securely attached
into the wall or cabinet fixture.
Figure 1

PM130 PLUS QuickStart www.satec-global.com
CONNECTION
To connect follow these steps (Figure 2 shows a 4W LV installation with conventional CTs):
1. Ensure that all incoming power sources are OFF.
2. Check that you have the appropriate power supply.
3. Connect the Power Supply inputs using 1.5 mm²/14AWG dedicated wires and breaker.
4. Connect to the external CTs by passing the external CTs wires through the meter CT cores.
Observe the arrow that indicates the current direction (Figure 2A). For HACS: connect the
red or white wire to the “-” and orange or black wire to the “+“ terminal.
5. In case of a retrofit application where each external CT ends with two wires (Note 2B):
5.1. Pass one wire through the meter CT core.
5.2. Connect the wire to one of the meter “optional CT wire termination”screws.
5.3. Connect the second wire from the external CT to the termination screw.
6. Connect the measured voltage inputs
7. Connect COM1 –RS-485 communication port
8. To connect the optional module:
8.1. Make sure that the power is turned off
8.2. Remove the module cover
8.3. Attach the module and fasten the screws
8.4. Connect the module I/O or communication (see Figure 2C for DI/O wiring)
9. Turn the power up
10. Make sure the diagnostic led is off
The “optional CT wire termination”
allows connection of the two wires
from the CTs. They have no internal
connection and their use is optional.
Figure 2
Note
2B
Figure 2A
Figure 2C

PM130 PLUS QuickStart www.satec-global.com
OPERATION
The PM130 PLUS is operated using the front panel which consists of a 3-line 7-segment
display, up to 33 LEDs (depending on model) and six keys as shown below:
There are two display modes: readings and menus.
Readings Mode
There are four groups of readings: Common measurement, Min/Max, Harmonics and Energy.
Use MAX/MIN or HIIIIIIor ENERGY to switch between groups, or to scroll within the
group, or simultaneous and to go to the first screen of the current display group.
Menu Mode
Press SELECT to enter menu mode (blinking line indicates the selection). SELECT to change the
selection, ENTER to drill down or ESC to go up. In editing mode use or to change the
value (a number or submenu), ENTER to accept it, or ESC to cancel.
The following chart shows the structure of the menus:


Phase rotation


Real Time Clock


Reset min/max, demands, etc.


Voltage angles


Basic configuration

Same as OPS (Options) menu


Current angles

.
COM2 setup



Relay status (*D)

.
COM2 setup (*E/G/R/P)


.
DI status (*D)


Relay Output (*D)


Counter value in 0.1 hours


Analog Output (*A)

.
Alarm setpoint


Network configuration (*E)


Diagnostics


Setpoints

.
Serial number



Display


Firmware version



Options


GPRS status (*G)
NOTE: Option availability depends on installed add-in module:
*D –Digital I/O; *A –Analog Output; *E –Ethernet; *G –GPRS; *R –RS232/422/485; *P –Profibus.
Diagnostic LED. Off = OK
Load bar graph
(full load according to CT
or in Display Setup)
Displayed
parameters
Calibration LED
(1 pulse/Wh or Varh)
Measurement scale
Communication indication
Main Display
Energy button & indication
(E/EH models) / Enter
Min/Max/Max Demand
button & indication
Harmonics button & indication
(EH model) / Escape
Select
Scroll up / down
 (Status)
Status Indications
 (Options) Read-only
display of the configuration
screens
 (Change) Configuration

PM130 PLUS QuickStart www.satec-global.com
CONFIGURATION
The essential configuration includes:
1. Basic measurement setup
2. Communication setup and testing
3. Resetting the min/max, energy, demands etc.
Additional recommended configuration: set points, TOU and data logging
Note: It may be easier first to configure communication and use PAS software for setup
Basic Measurement Setup
In any display screen, press SELECT x 3 (until  blinks), then press ENTER ( blinks), then
x 2 ()and ENTER to enter the Basic Settings Display.
Parameter
Description
Default
 (see below) 
Network wiring configuration


Transformation ratio of the Potential Transformers

.
Additional PT factor for EHV network


The Primary Rating Of The Current Transformers
(quick access to this parameter: press SELECT, then simultaneous and SELECT)

.(E & EH models)
Duration in minutes of the power demand period calculations
E = External pulse in DI1

.(E & EH models)
The number of blocks to be averaged for sliding window demands

.
Duration in seconds for voltage and current demand


The nominal frequency


Max. Demand Load Current in Amperes. 0 = CT primary current.

Wiring Mode
Setup
3-wire 2-element Delta direct connection using 2 CTs

4-wire 3-element Wye direct connection or 3PTs, and 3 CTs
 or *
3-wire 2-element Open Delta connection using 2 PTs, 2 CTs

4-wire 2½-element Wye connection using 2 PTs, 3 CTs
 or *
3-wire 2½-element Open Delta connection using 2 PTs, 3 CTs

4-wire 3-element Delta direct connection using 3 CTs
 or *
3-wire 2½-element Broken Delta connection using 2 PTs, 3 CTs
 or *
* LN or LL denotes the default use of L-L or L-N voltages (in thresholds, min/max, demands etc.)
Communication setup and testing
In any display screen, press SELECT x 3 ( blinks), then press ENTER ( blinks),
then x 3 (.) and ENTER to setup the built in RS-485 port (COM1).
If communication module is present, configure also COM2.
Resetting the min/max, energy, demands etc.
In any display screen, press SELECT x 3 ( blinks), then press ENTER ( blinks), then
ENTER to enter the reset menu. Select the value to be reset, press SELECT to select, then press
ENTER for 5 seconds until the  notification is changed to .
WI!
Copyright © 2013 SATEC Ltd.