SatKing SK-3500 User manual

USER’S MANUAL

1
English
CONTENTS
1. GUIDE ..............................................................................................................2
1.1 IMPORTANT SAFETY INSTRUCTIONS ..................................................................................2
1.2 UNPACKING ..................................................................................................................................2
1.3 PRODUCT OVERVIEW& ILLUSTRATION ..............................................................................3
1.4 INSTALLATION OF METER .......................................................................................................4
2. OUTLINE ..........................................................................................................5
3. THE MENU OSD INSTRUCTION ......................................................................6
3.1 SATELLITE FIND...........................................................................................................................6
3.2 LOOP SEARCH..............................................................................................................................9
3.3 PROGRAM INFO..........................................................................................................................9
3.4 ANGEL CALCULATION ...............................................................................................................9
3.5 MULTIMEDIA ..............................................................................................................................10
3.6 SATELLITE INSTALLATION......................................................................................................10
3.7 OTHERS........................................................................................................................................ 13
3.8 SYSTEM SETTING...................................................................................................................... 15
4. TECHNICAL SPECIFICATION ..........................................................................17

2
1. GUIDE
1.1 IMPORTANT SAFETY INSTRUCTIONS
Thank you for choosing our product. Before installation, we would like to
remind you some notes, which is very important for operating safely and
properly, as follows:
• Be sure to read this user manual before starting your operation.
• You must install the dish with correct direction and angle. If the dish is not
working properly, contact your local dealer.
• When the unit is suddenly moved to a hot area from a cold area, it may
cause some problems. In that case, turn o the power, and turn on again
after 1-2 hours.
• Keep meter placed in clean space with sucient ventilation.
• Do not cover the meter with or place it on a unit that emits heat.
• Clean the case by a soft cloth with a little washing liquid.
• Do not remove the cover.
• Do not let the unit exposed to extreme heat, cold or humid conditions.
• No liquids or any other materials to come inside of the unit.
1.2 UNPACKING
Open the package and make sure it includes all below items, if any missing,
please contact the reseller for replacement.
1. Digital Satellite Meter
2. User’s manual
3. AV cable
4. Car charger cable
5. Power Adaptor
6. Strap of carrying case
NOTE: Please refer to our actual configuration.

3
English
1.3 PRODUCT OVERVIEW& ILLUSTRATION
NO Description FUNCTION
1 LNB In Connect to satellite antenna cable
2 AV OUT Connect to AV port for TV
3 AV IN Connect to AV port for meter
4 USB Port Connect to USB memory
5 DC Slot Connect to adaptor input
6 Power Switch Turn on/o meter
7 Speaker Speaker integrated
8 Torch LED Night lighting
9 HDMI Use HDMI cable to connect for TV
10 LCD TFT LCD Screen
11 Power Power indicator light
12 22KHz 22KHz indicator light
13 13V/18v Vertical /Horizontal polarization voltage output light
14 LOCK Signal lock indicator light
15 Charger (Note1) Charger indicator light
16 F1 Auxiliary function key
17 F2 Auxiliary function key
18 F3 Auxiliary function key
19 SCAN ‘Quick Search’menu shortcut key
20 AV-S(Note2) Switch AV mode: AV Normal; AV IN and AV out
21 NEVIGATION KEY Volume Control or move cursor, channel or change,
confirmetc

4
NO Description FUNCTION
22 MENU Show the main menu on the screen or jump back to
previous menu in sub-menu setting conditions
23 EXIT Escape from present menu and save the settings
24 0-9 Number key to select channels or enter programming
25 INFO INFO key
26 MUTE MUTE
27 Red & TTXT Red KEY & Teletext interface
28 Green & SUBT Green key & Subtitle interface
29 BLUE &AUDIO Blue key & Audio interface
30 Orange &TV/R Orange key & TV and radio switch
31 When power on the meter ,displays the battery level
Note1: When the adapter insert into dc slot, charge indicator is often bright. When
the batteries charged sucient, the charge indicator will go out.
Note2: In the AV out mode, speaker is o.
1.4 INSTALLATION OF METER

5
English
2. OUTLINE
• 3.5 Inch High Definition TFT LCD Screen
• Fully DVB-S/DVB-S2, MPEG-2/MPEG4 compliant
• MPEG-2 / H.264 Hardware decoding
• Digital meter for signal strength and quality
• Supports scan of Auto,Blind,Manual or NIT
• Sound and Light Alarm for Locking Signal
• Auto Calculate Angle of AZ ,EL
• Supports DISEQC 1.0/1.1/1.2 ,0/22khz Tone
• Speaker Integrated
• Support both AV out and AV in
• LNB short protect
• 7.4V/3000mAh Li-Ion Battery Included
• Software upgrade via USB port
• Easy to carry

6
3. THE MENU OSD INSTRUCTION
If you have installed and connected the cables to the receiver, pressing MENU
to display the Main Menu.
• Satellite Find
• Loop Search
• Program Info
• Angle Calculation
• Multimedia
• Satellite Installation
• Others
• System Setting
Press the keys of YZAB to move the cursor up or down in the menu
interface, then use OK to confirm a selection.
3.1 SATELLITE FIND
Select Satellite Find, then press OK into the Satellite Find.
3.1.1 SATELLITE
Press OK into the satellite list. Use YZ
key to move the cursor, then press OK
to select the satellite of you want.

7
English
3.1.2 LOCAL FREQUENCY
Press AB key into the LNB list. Use YZ
key to move the cursor then press OK to
select the LNB of you want.
3.1.3 TRANSPONDER
Press AB key into the TP list. Use YZ key
to move the cursor then press OK to select
the TP of you want.
3.1.4 FREQUENCY
Frequency of the current transponder, Input the value by using the number
keys.
3.1.5 SYMBOL RATE
Symbol rate of the current transponder, Input the value by using the number
keys.
3.1.6 POLARITY
Press AB key to change vertical or horizontal of polarization.
3.1.7 TONE
Press AB key to turn on or o 22kHz TONE Switch.
3.1.8 BEEP TONE
Press AB key to Switch beep tone. If we open the beep tone, the beep of
lock alarm will open when we enter into the search screen.
3.1.9 DISEQC MODE
Press AB key to set the type of port as DiseqC 1.0/1.1, DiseqC 1.2/USALS or
Unicable.

8
3.1.10 DISEQC TYPE & INPUT
If we select diseqc1.0/1.1, we can press AB
key to set the port number. If select Unicable,
we can press AB to select IF Channel, and
use number key to input Center Frequency.
3.1.0.1 Quick Search
In the Satellite Find interface, you can press OK to
enter the quick search.If you have set the
Longitude and Latitude under the system setting,
the angle of LNB, the orientation and elevation of
antenna all will be displayed on the screen.
• TP Scan: Press OK to search the current TP.
• Auto Scan: Press the red key to auto
blind search the current satellite.

9
English
3.2 LOOP SEARCH
Select Loop Search, then press OK into the Loop
Search.There will have 8 TP on your sight .
Press OK to enter TP Edit, you can edit Satellite
and Transponder.
3.3 PROGRAM INFO
In the Program Info, you can check the information
of the current TV.
3.4 ANGEL CALCULATION
You can edit angel parameter of the satellite that
you select.

10
3.5 MULTIMEDIA
Select Multimedia, then press OK into the
Multimedia.
• Movie
Press red key to change the folder file viewing
to detailed list.
Press green key to the mode option of play files
and text encode, then press MENU return.
Press orange key to change mode to big Icon
browsing. Press the arrow keys to move the
cursor, then press OK to enter the file.
In the play interface:
F1 Key: Normal play.
F2 Key: Pause.
F3 Key: Fast backward. Press F1 key return.
SCAN Key: Fast forward. Press SCAN key return.
• Music& Photo
Please refer to the Movie operating.
3.6 SATELLITE INSTALLATION
• Satellite Setting
• Auto Scan
• TP Manager

11
English
3.6.1 SATELLITE SETTING
In the all Satellites Setting:
Press red key into the Transponder interface.
Press green key into auto scan interface.
Press YZ key to move the cursor, then press
OK to change the satellite select or unselect.
Press AB to set the single satellite setting.
In the setting interface:
1. TP Manage: press red key into TP manager.
2. Auto Scan: press green key into auto scan.
3. LNB: Press AB key then change the LNB
frequency.
4. Transponder: Press AB key then change
the current TP.
5. DiSEqc1.0: Press AB key to change the
DiSEqC port.
6. DiSEqc1.1: Press AB key to change the DiSEqC port.
7. Motor: Press AB key to change the DiSEqC port.
If we select DiSEqC1.2/USALS, press OK into
the motor interface.
• Transponder: Press OK to change the current tp.
• Mode: A, Position
A1 Direction: Press AB key to move direction
to west or east.
A2 Position: Set the satellite save position.
• Mode: B, Drive to Zero
Move the cursor to GO, then press OK , the motor will go to zero.
• Mode: C, Drive to stored position
Move the cursor to GO, then press OK , the motor will go to position of we
have saved in mode A Position.
• Mode: D, Drive to Satellite
Move the cursor to GO, then press OK , the motor will go to position of
auto calculate.
• Mode: E, Recalculate
E1 Direction: Press AB key to move direction to west or east.
E2 Recalculate: Recalculate the satellite position.
• Mode: F, Set East Limit or Set west Limit

12
Limit the motor move to east or to west.
F1 Direction: Press AB key to move direction to west or east.
F2 Store: Save the satellite position of A2
• Mode: G, Set Limit enable or disable
Set the limit enable or disable.
8. Unicable: Press AB key to select Unicalbe then press OK into the Unicable
setting.
• Transponder: Press AB key to change the current TP.
• IF Channel: Press AB key to change SCR
channel.
• Center Frequency: Use number key to input number.
3.6.2 AUTO SCAN
In the Sat/Tp Manager submenu, select Auto Scan
into Automatic SAT Scan.
• Satellite: Press AB key into the satellite list. Use
YZ key to move the cursor, then press OK to
select the satellite of youwant.
• Transponder: press AB key into the TP list. Use
YZ key to move the cursor, then press OK to
select the satellite of you want.
• NIT: press AB key to switch network searcher on/o.
• Program: TV search type ALL/FTA.
• Scan Mode: scan mode select, we can select Default TP / One TP/Blind.
• Scan Select: scan all satellites of selected or the current satellite.
3.6.3 TP MANAGER
In the Sat/Tp Manager submenu, select
Transponder into Transponder.

13
English
Press YZ key to select the current satellite.
• Edit Sat
Press red key to edit satellite.
NO.: Satellite number.
W-E: Switch the satellite longitude west or
east.
Longitude: Use number key input value.
Satellite Name: Press OK will open the
keyboard, use the direction key input satellite
name.
• Add Sat
Press orange key to add a satellite.
Press AB key to TP manager.
• Edit Tp
Press red key to edit TP.
NO.: TP number.
Frequency: Use number key input value.
Symbol Rate: Use number key input value.
Polarity: Press AB to change polarity.
• Add Tp
Press orange key to add a TP. Please refer to
TP edit operations.
3.7 OTHERS
• TV Channel Editor
• Radio Channel Editor
• EPG
• System Info

14
3.7.1 TV CHANNEL EDITOR
Select TV Channel Editor, then press OK into
the CH List.
• Edit
Press red key into edit list, you can edit
program name, move program, sort program,
and skip program.
• Lock
Choose the program you want to lock, and press green key to finish the
operation.
• Del
Choose the program you want to delete, and press orange key to finish the
operation.
• Sat
Press blue key to select All Satellite or the current satellite.
3.7.2 RADIO CHANNEL EDITOR
Please refer to TV Channel Editor.
3.7.3 EPG
Press YZ key to change program. If the
current program has EPG information, it will
appear on the right side of the window.
Press AB key to change the day of the EPG
information.

15
English
3.7.4 SYSTEM INFO
There are some system information you can
see.
3.8 SYSTEM SETTING
• Country Setting
Press AB key to change the country
• OSD Language
Press AB key to change the OSD Language.
• TV Format
Press AB key to change the TV Format.
• Video Output
If we connect HDMI interface, we can press AB key.
• TV Resolution
On the basis of the Video Output choice, we can press AB key to change the
TV resolution.
• Digital Audio Output
Press AB key to change the LPCM or RAW format.
• Time Zone
Press AB key to change the Time Zone.
• Channel Lock
If open channel lock, you will input password before enter submenu.
• PWR Unit
Press AB key to change the PWR unit.
• Key Beep Tone
Press AB key to switch key beep tone on/o.

16
• Flashlight
Press AB key to switch Flashlight on/o.
• Upgrade
Will update the file into the USB, then insert the machine. Press OK to update
interface, use the direction key to select update file, and press OK to update.
Warning: Please don’t turn power off or pull out the USB, otherwise it will
damage the machine’s software, and can’t boot again.
• Factory Setting
Press AB key, then press OK to confirm factory reset.
NOTE: if you set factory setting, all the user settings and the database will be
reset.

17
English
4. TECHNICAL SPECIFICATION
TRANSMISSION STANDARDS
DVB-S2/S, MPEG-2,MPEG-4,H.264
SATELLITE INPUT/DEMODULATION
Connector Type F Type
Input Frequency 950 to 2150 MHz
Signal Input Level -65 to -25 dBm
Band Switch Control 22KHz
LNB Supply 13V/18V, IMax 400mA
Demodulation Type QPSK,8PSK
Symbol Rate 2<Rs<45Mband(SCPC/MCPC)
LCD FEATURES
LCD Type TFT Transmissive
Number of Dots 480(RGB) x272
Active area (WxH) 70.02x52.58 mm2
AV output interface
Connector Type 3.5 mm jack
Video Output CVBS
Audio Output Stereo Audio L/R output
HDMI output connecter
Format HDMI 1.3a
AV input interface
Connector Type 3.5 mm jack
Video Input CVBS
Audio Input Stereo Audio L/R input
AUDIO/VIDEO PROCESSING
Video decompression
MPEG‐2 MP@HL, MPEG‐1
Decoding,MPEG‐4 ASP@L5 HD
resolution,H.264 MP&HP@L4,HW JPEG
decoding
Resolving rate PAL‐25 frame@720*576,NTSC‐30
frame@720*480
Signal compatibility Support conversion for dierent video
formats
Video Format 4:3,16:9,By Pan & Scan and Letter Box
conversion
Audio Decompression MPEG‐1 Layer I/II, MPEG‐2 Layer I/II

18
Audio Output Mode Stereo, Mono,R/L
DATA SERVICE PORT
Connector USB
Data Protocol USB2.0 interface
File Management System NTFS,FAT32,FAT16
File Format wma,mp3,mp4,avi,jpg,jpeg,bmp,img
MICROPROCESSOR
Microprocessor 78346
Clock Frequency 550MHz
SDRAM Memory DDR2 512Mbit
POWER SUPPLY
Li‐Ion Battery 7.4V/3000mAh
Adapter OUTPUT :DC12V/1.5A, INTUPT:
100‐240VAC 50/60Hz
Power Consumption Max. 10W
PHYSICAL CHARACERSTICS
Size (W x D x H) 10.1x17.7 x4.7(cm3)
Net Weight 0.46kg

19
English
5. TROUBLE SHOOTING
Problem Possible Causes What To Do
No display light up Power switch is not
on or run out of batteries
Check to make sure power
on even on adapter
No sound or picture,
but the front panel
power light is ON.
AV IN jack insert, but no
video input Pull out AV IN cable
No sound or picture
The satellite dish is not
pointing at the satellite.
Adjust the dish. Check the
Signal Level in the Antenna
Setup Menu
Bad picture/Blocking
Error
No signal or weak signal
Check the cable connections.
LNB and other equipment
connected between the LNB
and the meter and adjust
the dish.
The satellite dish in not
pointing at the satellite
Adjust the dish.
Signal is too strong Connect a signal attenuator
to the LNB input
Satellite dish is too small Change to a larger dish
LNB noise factor too high Change to an LNB with
lower noise factor
The LNB is faulty Change the LNB
AV out No
picture(Video)
The system is connected
by SCART cable and TV is
not in AV mode.
Check the UHF channel fixed
in your system and tune the
UHF properly.
The key is not working
Out of battery Even on adapter
Key blocks make sure no blocks
between the front panel
Note: If you still can not resolve the problem with above reference. Please
contact the local dealer or their after-sales service center.