Savage Star light User manual

USER MANUAL

LED PANEL STAR LIGHT

professional photography made simple

800.624.8891 savageUniversal.com

professional photography made simple

800.624.8891 savageUniversal.com

USAGE INSTRUCTIONS

STAR LIGHT

CONTENTS:

Collapsible star shaped LED panel light

Tiltable light stand adapter

AC power cord

Ball head

(2) NP-F770 batteries

(2) Battery chargers

Molded carry case

SETUP:

(1) Thread the light stand adapter into the bottom of the Star Light. If the light stand used

(sold separately) has a 1/4”-20 male thread, thread the Star Light onto the light stand.

(2) If the light stand used has a top stud (no thread), loosen the lower knob on the light

stand adapter until the silver reversible thread adapter releases. Slide the stand

adapter without the silver reversible adapter over the stud and tighten using the lower

knob.

(3) If using the power cord, attach to the back of the Star Light and tighten down to

secure.

(4) If using the included batteries, slide each into the designated battery dock on each

side of the light base until it locks in.

Before use: Plug the included battery chargers into household sockets. The LED light on

the chargers display red while charging and turn green when the batteries are

fully charged. This can take up to 6 hours if the batteries are completely drained when

charging begins. The included batteries can power the Star Light for up to 70 minutes at

full power before needing recharging.

Open the Star Light beginning with the front arm. Turn clockwise for 4 clicks. Turn the

second arm 3 clicks, and so on until the 5 arms resemble a 5-point star. The last arm will

stay in its initial position pointing straight down.

*DO NOT FORCE THE ARMS OR TRY TO OPEN IN A COUNTERCLOCKWISE POSITION.

To close, reverse the above steps until all 5 arms are aligned and in the down position.

ACCESSORIES:

(5) Mirrorless cameras and mobile phones can be attached using the included ball head.

Mirrorless cameras can be attached to the ball head by threading onto the

¼”-20 male thread on top of the ball head. For cell phones, thread a phone holder (sold

separately) into the top of the ball head. Loosen the tightening knob near the

bottom of the ball head to attach to the shoe mount on the Star Light. Slide the shoe on

the bottom of the ball head onto the cold shoe on the Star Light. Tighten down using the

knurled knob to secure.

(6) To turn on, press the On/Off button directly below the LED display and the Star Light

should illuminate.

MANUAL CONTROL:

Depending on the setting selected when the light was last used, the digital readout will

display either a number between P1 and P100 or a number between 3200 and 5500.

P = POWER.

Adjust the power between 1 and 100 to achieve the desired light intensity.

3200 - 5500 = KELVIN TEMPERATURE.

Use this function to either accurately reproduce the true colors of the subject (5500K /

daylight) or reduce to (3200K / tungsten) to produce a warmer look. Most environments

are somewhere between 3200K and 5500K because of multiple light sources in the

room. This setting can also be used to change the Kelvin temperature anywhere in

between 3200K and 5500K to approximately match the available light in the room.

(7) To change from selecting intensity to Kelvin temperature, press the controller button

one time.

4 CLICKS

3 CLICKS

2 CLICKS

1 CLICK

ACCESSORY SHOE MOUNT

BALL HEAD

DIGITAL READOUT DISPLAY

POWER BUTTON

CONTROLLER KNOB

MOBILE APP CONTROL:

The color temperature and brightness can be controlled remotely using the free Savage Light Manager app

available for download in both the Apple App Store and Google Play Store.

With the Bluetooth setting on your phone enabled, turn the Star Light on by pressing the controller knob on the

back panel once.

Open the Savage Light Manager app on your phone. Pairing the Star Light in your phone manually is unnecessary.

The Star Light should sync with the app automatically when the app is opened. The light will not pair until the app

is opened.

Note: The light will not unpair unless the Bluetooth function on your phone is turned off in the settings menu or the

battery is removed. Remove the battery for storage to prevent accidental draining between uses.

COLOR TEMPERATURE WHEEL (C)

The Savage Star Light can be set to 5500K / daylight output. It can also be set to 3200K / tungsten light that is

similar to a cool white incandescent look. In many rooms, there are multiple light sources in the room that are

blending together. In those instances, the light in the room is neither daylight nor tungsten. The Kelvin wheel allows

the user to blend the 2 light sources to match the available light in the room. It can also be used to “warm” or “cool”

the subject for creative purposes.

To enable the color temperature blending function on the Star Light, tap the “Color Temperature Wheel” (C).

You will then be able to slide your nger around the color wheel (1) to achieve the color temperature of your

choice. Once the desired color has been selected, scroll right on the white Light Output Bar (2) to increase or left to

decrease light output. Below the Light Output Bar (2), there are 6 “Preset Buttons”. They are not programmable.

The rst button in the Standard presets labeled will decrease the light output to 0% (the light will still be in the On

position). The second button labeled “3200K” will adjust your light to tungsten. The third button labeled “5600K” will

set the light to daylight color temperature. The 25% and 5% buttons are for reducing the light output at the selected

Kelvin temperature.

The Light Output Bar (2) can also be used for ner light output adjustments.

MANAGE BULBS:

FOR ANDROID:

Name your light:

Tap the “List” icon at the top left of the app. A side bar will open up that lists “Manage Bulbs”

Click the “Settings” icon next to “Manage Bulbs”. You should see the light listed.

It will begin with “Magic….”

Tap the wrench icon next to the listed light. A box will open to rename. Type in the name of your choice and select

OK. If you have multiple lights, it is possible to control them separately using the Savage Light Manager.

IPHONE:

Tap the “List” icon at the top left of the app. A sidebar will open up that lists “Group Manage” and “My Device”. Click

“Group Manage”, then “Add”. Type in the name of your choice and select OK.

Repeat above steps to rename the second light.

Important: If you are using the app on more than one phone, you can only pair the device/devices to one phone at

a time. If the device is paired to more than on phone at the same time, the functions will not work.

TO CONTROL MORE THAN ONE LIGHT USING: DEFAULT GROUPS

Tap the “List “icon at the top left of the app

A side bar will open up that lists “Default Groups”

Tap on right pointing arrow next to “Default Group” and you should see each paired light.

Note: only lights that are currently turned on will be visible. If the light is controllable with the app, it will be

highlighted with a blue background for Android or gray for iPhone.

If multiple lights are highlighted, then the app will control all at the same time.

If the light does not have a blue/gray background, tap on it in the app. Blue/gray background will come on and the

light will be controllable. Note: the bulb to the left of the named light should appear to be lighted. If it does not, tap

the bulb and it will appear to light.

Note: The chain to the right side of the light should appear unbroken, if the 2 links appear to be separated, tap on

the chain until they appear connected. Breaking the chain can be used when temporarily disabling the light from

the app is desired. Only highlighted lights will be controlled by the app. To control lights separately, tap any light

icon and the blue highlight will disappear. That light will no longer be controlled by the app allowing the user to

control each light independently.

DAYLIGHT KELVIN MODE

COLOR TEMP WHEEL (C)

STANDARD PRESETS

OUTPUT LEVEL (2)

COLOR WHEEL (1)

professional photography made simple

800.624.8891 savageUniversal.com

STAR LIGHT USAGE INSTRUCTIONS

MANAGING BULBS

CLICK LIST BUTTON

LIGHT MANAGER

professional photography made simple

800.624.8891 savageUniversal.com

USAGE INSTRUCTIONS

Troubleshooting

Note: The Savage Light Manager was designed to work with multiple Savage lighting products. The app has extended features which may not be compatible with

all lights. The Savage Star Light was designed for use with the “Color Correcting” Wheel to adjust color temperature and brightness. The RGB, special effects and

Music/Mood features are not compatible with the Savage Star Light.

Problem: Light behaves erratically.

FOR ANDROID:

If the app has been running in the background for extended periods of time, the app’s cache can ll up.

Solution:

To solve, close the “Savage Light Manager” app.

Go to “Settings” in your phone.

In settings, go to “Application Manager”.

Scroll to the app “Savage Light Manager”.

Tap “Storage”.

Tap “Clear Cache”.

This will likely solve the issue. Re-open the “Savage light Manager App” and re-try.

If light fails to pair with your device’s Bluetooth, GPS/Location Service may need to be enabled.

FOR iPHONE:

Close out of the app completely and then re-open. You can also try to remove the battery from the light and re-attach or restart the phone completely.

If the light appears to be paired but the light cannot be controlled, see instructions for Default Groups. The light that is being used should be highlighted in blue/gray, the bulb to