Savant HCX-4KHDR40 User manual

HCX-4KHDR40 | 009-1673-00 | 180906
Copyright 2018 Savant Systems, LLC
1 of 2 45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
Box Contents
(1) HDBaseT Transmitter
(1) HDBaseT Receiver
(1) Power Supply (Regional clips included)
(4) Brackets
(2) 3-pin Control Connector
(1) IR Emitter
(1) IR Connector Cable
(1) IR Receiver
(1) Regulatory Card
Specifications
Environmental
Temperature 32° to 113° F (0° to 45° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weights
Height 0.60 in (1.52 cm)
Width 5.37 in (13.64 cm)
Depth 2.92 in (7.42 cm)
Weight Shipping 2.05 lb (0.93 kg)
Power
Input Power 18V DC 3A
Power
Consumption 54 Watts (maximum)
Power over
HDBaseT (PoH) Can be used to power the second device.
Video
HDR Supported
Supported
Formats
800x600
1024x768
1280x760
1280x800
1280x960
1280x1024
1360x768
1366x768
1440x900
1600x900
1600x1200
1680x1050
1920x1080
1920x1200
3840x21601,2,3,4
4096x21601,2,3,4
1 = at 24 Hz | 2 = at 25 Hz | 3 = at 30 Hz | 4 = at 60 Hz
Audio
Supported
Formats
Pass-through of all HDMI audio formats are
supported.
Compliance
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Device
APower LED O: Device is o. No power applied.
Red: Main board is powered.
BStatus LED O: HDBaseT processor is not running.
Blinking Blue: HDBaseT processor is running.
CHDCP LED
O: No HDMI stream.
Blue: HDCP present in HDMI stream.
Rapid Blinking Blue: Non-encrypted HDCP
signal.
DLink LED
O: No connection established.
Blue: Connection established between
Transmitter and Receiver.
EPower Input 18V DC locking power connection.
(Only one power connection needed.)
FHDBaseT RJ-45 HDBaseT connection.
GIR In
3.5 mm IR input for IR pass-through. Transmits
IR signals via an IR Flasher (5V tolerant) to
devices with an IR input or IR receiver.
HIR Out
3.5 mm IR output connection. Transmits IR
signals via an IR Flasher (5V tolerant) to
devices with an IR input or IR receiver.
IRS-232
3-pin Control Connector. Transmits and receives
serial data to and from serial controllable
devices. For pin-out information,
refer to the RS-232 Wiring section below.
JHDMI
19-Pin Type A HDMI female digital audio/video
input. Supports HDMI 2.0b HDMI 2.0 complaint
cable required for 4K content.
TX RX G HDMI OUTIR OUTIR IN
LINKHDCPSTATUSPOWER
JIHGFE
D
C
B
A
Front Panel
Rear Panel
HDBaseT Extenders with 4K HDR up to 40M (HCX-4KHDR40)
Quick Reference Guide

HCX-4KHDR40 | 009-1673-00 | 180906
Copyright 2018 Savant Systems, LLC
2 of 2 45 Perseverance Way, Hyannis, MA 02601
Savant.com | 508.683.2500
Installation
An HDBaseT extender can be placed on a standard 1U rack shelf. Or
the extender can be installed using the included mounting brackets.
To install the mounting brackets follow the steps below.
1. Remove the two case screws on the side of the device
(Shown in the image below).
2. Align the bracket using the top holes.
NOTE: This will leave an air gap behind the device.
3. Replace the case screws attaching the bracket.
Category 6 or greater twisted pair cable with RJ45 connectors
between the transmitter and the receiver is recommended.
TIA/EIA-568B straight-through wiring connections must be used.
Transport Distance (4K)
Cat6 115ft (35m)
Cat6a/7 131ft (40m)
Transport Distance (1080P)
Cat6 197ft (60m)
Cat6a/7 230ft (70m)
HDBaseT Cable Information
RJ-45 Connector
(Gold pins facing up)
TIA/EIA-568B
12
IR Wiring
IR Emitter
Connect to 3.5 mm IR Out to control a IR device.
3
2
1
Pin 1
IR - (Black)
Pin 2 IR + (Red)
Pin 3
Not Used
IR Connector Cable
Connect to 3.5 mm IR In to pass-through IR control from a Savant
Controller.
IR Receiver
Connect to 3.5 mm IR In to pass-through IR control. Not
commonly used in a Savant Deployment.
IR Control is pass-through only.
RS-232 control signal pass-through only.
Serial control connection are made using
a 3-pin Control Connector supplied with
the device. The wire slips into the hole and
locks with a screw located at the top of
the connector.
RS-232 Wiring
Pin 1
Ground
Pin
2
Transmit
Pin 3
Receive
1 3
2