Savant HST-STUDIO55WS-SUR User manual

HST-STUDIO55WS-SUR | 009-1878-00 | 191108 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2019 Savant Systems, LLC 1 of 2 Savant.com | 508.683.2500
Box Contents
(1) Smart Series WiSA Soundbar (HST-STUDIO55WS-SUR)
(1) Soundbar (093-3183-xx)
(1) Standard Grille (093-3181-xx)
(1) Power Cord (064-0480-xx)
(2) 6-Pin Control Connector (028-9352-xx)
(1) Install Kit (075-0241-xx)
(2) Wall Mounting Bracket (071-1130-xx)
(1) 3mm Allen Wrench (015-0222-xx)
(4) M5x10mm hex screw (039-0440-xx)
(4) 25mm Washer 10mm ID (039-0438-xx)
(2) Rubber Feet (073-0007-xx)
(1) IR Learner (064-0511-xx)
(1) Product Regulatory Insert (009-1873-xx)
(1) Quick Reference Guide (this document)
Optional Accessories (sold separately)
–Smart Audio Soundbar TV Mount Hardware
(MNT-STUDIO55WS-TV-xx)
–Custom Grilles matched to Flat Panel TV’s
Specifications
Environmental
Temperature 32° to 104° F (0° to 40°C)
Humidity 10% to 90% (non-condensing)
Dimensions and Weights
Height 4.17 in (10.59 cm)
4.61 in (11.71 cm) with included Grille
Width 53.41 in (135.65 cm)
Depth 2.25 in (5.71 cm)
2.40 in (5.93 cm) with included Grille
Weight Net: 21.7 lbs (9.9 kg) with included Grille
Shipping: 27.9 lb (12.7 kg)
Power
Input 120/240V AC (50/60 Hz) 3.6A
Maximum 250W
Operating Parameters
Frequency
Response 80 Hz - 40 kHz +/- 3 dB
Sensitivity 89 dB @ 2.83V/1 meter
Networking
Supported
Standards IEEE 802.1 AVB/TSN
WiSA
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick UL
RoHS Compliant
Minimum Supported Release
Savant Software da Vinci 9.2
Studio 3.1
Savant® Smart Series WiSA Soundbar [HST-STUDIO55WS-SUR-xx]
Quick Reference Guide
Front Panel
A
B
AFront Tweeters (3) 25 mm Vifa XT Super Audio Tweeters
BMidrange/
Woofers
(6) 89 mm Long Throw Carbon Fiber
Midrange/Woofers
Side and Bottom Panel
A
B
AStage Tweeters (2) 19mm Silk Tweeters
BMounting Slide (2) Captive M5 threaded bracket
Installation
Wall Mount
1. Attach the Wall Mounting Brackets to the wall using the appropriate
fasteners to account for the weight of the soundbar.
NOTE: The two wall brackets must be far enough apart so the
soundbar does not wobble on the wall.
2. Make the power and control connections before the soundbar is
attached to the brackets.
3. Attach the Soundbar
Rubber Feet
The included rubber feet must be used with the included grille.
1. Align the foot with the mounting slide.
2. Remove the waxed paper from the adhesive
3. Use one of the included hex screws to attach the foot to the
mounting slide.
4. Repeat for the second rubber foot.
Host Mode
Host mode can be disabled/enabled from the device’s Web UI. For
more information see the IP Audio Products with Integrated Host
Deployment Guide (009-1839-xx)
Further Product Information
To view available documentation, detailed product specs, and more:
–Visit the Savant Knowledge tab via the Savant Customer
Community to search all Savant documentation.

HST-STUDIO55WS-SUR | 009-1878-00 | 191108 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2019 Savant Systems, LLC 2 of 2 Savant.com | 508.683.2500
Rear Panel
100-240 V~ 50-60 HZ 2.2A
Smart Audio Soundbar
IR
Ethernet
ResetStatus
Digital Audio
In
RS232
GND
TX
RX
GND
TX
RX
2
1
-
1
+
-
2
+
-
3
+
IR
Learner
Sub
Out
A B C D
E
F
G
H
I
AStatus LED
O: Embedded processor is resetting, or is powered up, and is booting the embedded firmware.
Green: Host has established communications with the embedded system.
Green Blinking: Embedded system is ready, but no communication has been established with the host.
Red: Host has determined the firmware needs to be updated, but a problem occurred during the process that will
initiate a reset.
Red Blinking: Embedded firmware is running, but has not received a DHCP IP Address.
Amber: Host is updating the embedded firmware.
Amber Blinking: Embedded system has a valid link local IP Address and is connecting to the host.
Hardware Failure: If a hardware failure occurs, the status LED indication will be interrupted every three seconds with
a solid red indication. For example, if the LED is blinking green when a hardware failure occurs, the LED will alternate
between blinking green and solid red at three-second intervals.
B
Digital Audio
Input
Digital optical audio inputs (TOSLink).
Inputs support up to 192kHz/24-bit digital audio and up to 5.1 encoded audio.
C
Ethernet 8-pin RJ-45 port 10/100 Base-T auto-negotiating port.
Supports Audio Video Bridging (AVB).
DSerial Ports (2) RS-232 Ports
Uses 6-pin Screw down plug-in connection. Transmits and receives serial data to and from serial controllable devices.
E
Reset
Resets the network.
Hold Reset Button for 5 seconds while powered on to clear network settings. Status LED will rapidly blink red when
reset is complete.
FIR Learner 3.5 mm connection, for use with the included IR learner (Studio Only).
GSub Out 3.5 mm analog connection, Direct line level, 2.1 VRMS max.
H
IR Ports
(3) IR Ports
Uses 6-pin IR Connectors to send IR signals to control devices with an IR input or IR receiver via an IR flasher (5V
tolerant only).
I
Power Input 120/240V AC (50/60 Hz)