Savant IP-STUDIO46-2CH Series User manual

IP Audio Soundbars | 009-1792-01 | 190618 1 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2019 Savant Systems, LLC Savant.com | 508.683.2500
Savant® IP Audio Soundbars
Quick Reference Guide
Box Contents
(1) IP Audio Soundbar
(1) Power Cord
(2) 6-Pin Control Connector (028-9352-xx)
(1) Install Kit (075-0214-xx)
(2) C-Shape Bracket (093-3114-xx)
(2) L-Shape Bracket (093-3115-xx)
(2) Wall Mounting Bracket (071-1130-xx)
(2) Bracket Extension 50x90 (071-1112-xx)
(2) Bracket Extension 70x90 (071-1113-xx)
(2) UMB Stabilizer (015-0223-xx)
(1) 3mm Allen Wrench (015-0222-xx)
(8) M5x10mm hex screw (039-0440-xx)
(4) M4x11.5mm hex screw (039-0441-xx)
(4) M5x11.5mm hex screw (039-0442-xx)
(4) M6x11.5mm hex screw (039-0443-xx)
(4) M8x11.5mm hex screw (039-0444-xx)
(4) M10x11.5mm hex screw (039-0445-xx)
(4) 25mm Washer 5mm ID (039-0437-xx)
(4) 25mm Washer 10mm ID (039-0438-xx)
(1) Product Regulatory Insert (009-1732-xx)
Optional Accessories
–Custom Grilles matched to Flat Panel TV’s (sold separately)
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Specifications
Dimensions and Weight without Grille
Height 4.17 in (10.59 cm)
Width 44.76 in (113.70 cm) - IP-STUDIO46-2CH-xx
53.41 in (135.65 cm) - IP-STUDIO55-2CH-xx
Depth 2.25 in (5.71 cm)
Weight
Shipping:
22.6 lb (10.3 kg) - IP-STUDIO46-2CH-xx
29.3 lb (13.3 kg) - IP-STUDIO55-2CH-xx
Products
IP-STUDIO46-2CH-xx
IP-STUDIO55-2CH-xx
Power
Input Power 100/240V AC (50/60 Hz)
Maximum Power
Draw 250W
Regulatory
Safety and
Emissions
FCC Part 15B CE Mark C-Tick UL
RoHS Compliant
Minimum Support Requirements
Software
Release da Vinci 8.10
Networking
Supported
Standard IEEE 802.1 AVB/TSN switches
Operating Parameters
Frequency
Response 80 Hz - 40 kHz +/- 3 dB
Sensitivity 89 dB @ 2.83V/1 meter
Front Panel
A
Front Tweeters
(2) 25 mm Vifa XT Super Audio Tweeters
- IP-STUDIO55-2CH-xx
(2) 25 mm Vifa DX Super Audio Tweeters
- IP-STUDIO46-2CH-xx
B
Midrange/
Woofers
(4 or 6) 89 mm Long Throw Carbon Fiber
Midrange/Woofers Side and Bottom Panel
A
B
AStage Tweeters (2) 19mm Silk Tweeters
BMounting Slide (2) Captive M5 threaded bracket
Bracket Selection
TV Thickness Bracket Extension Minimum wall
mount depth
0.9 - 1.2 in C-Shape None 1.1 in
1.9 - 2.8 in C-Shape 50 mm 1.1 in
2.7 - 3.6 in C-Shape 70 mm 1.1 in
2.1 - 2.5 in L-Shape None None
3.0 - 4.0 in L-Shape 50 mm None
3.8 - 4.7 in L-Shape 70 mm None
IP-STUDIO46-2CH-xx
IP-STUDIO55-2CH-xx
AB

IP Audio Soundbars | 009-1792-01 | 190618 2 of 2 45 Perseverance Way, Hyannis, MA 02601
Copyright 2019 Savant Systems, LLC Savant.com | 508.683.2500
Installation
The included install brackets are designed to be used with the VESA
Mounting points on Flat Panel Televisions. The Installer MUST verify
that the TV mount/stand can hold the excess weight of the soundbar.
The soundbar can be mounted above or below a TV. The example
below shows it being mounting below a TV.
1. Remove the TV from the mount/stand.
NOTE: This may require two people.
2. Place the TV display side down on a soft non-abrasive surface.
3. Remove any existing mounting bracket and screws from the VESA
mounting points.
VESA
mounting points
4. Choose the desired mounting bracket (use the Bracket Selection
table on the previous page). Find the screws that fit the TV’s VESA
mounting points.
5. Attach the mounting bracket to the TV. The soundbar brackets
should be between the TV and the TV mount.
Brackets
Aligned with the VESA mounting points
6. Adjust the length of the brackets
7. Attach the optional extension brackets if needed.
8. Attach the soundbar.
Optional Extension Bracket
L-Shape Bracket shown here
9. Reattach to the TV mount/stand.
For more information on installing a soundbar see the Savant Speaker
and Soundbar Install Guide on the Savant Customer Community.
Rear Panel
A
IR
(3) IR Ports
Uses 6-pin IR Connectors to send IR signals
to control devices with an IR input or IR
receiver via an IR flasher (5V tolerant only).
See IR Wiring section for important
precautions regarding IR functionality before
making any connections.
BRS-232
(2) RS-232 Ports
Uses 6-pin Screw down plug-in connection.
Transmits and receives serial data to and
from serial controllable devices. For pin-out
information, refer to the RS-232 Wiring
section below.
C
Ethernet
8-pin RJ-45 port
10/100 Base-T auto-negotiating port.
Supports Audio Video Bridging (AVB).
DPower 100/240V AC (50/60 Hz)
EStatus LED
Green Blinking: Embedded system is ready,
but no communication has been established
with the host.
Green: Host has established communications
with the embedded system.
Red Blinking: Embedded firmware is
running, but has not received a DHCP IP
Address.
Red: Host has determined the firmware
needs to be updated, but a problem
occurred during the process that will initiate
a reset.
Amber Blinking: Embedded system has a
valid link local IP Address and is connecting
to the host.
Amber: Host is updating the embedded
firmware.
O: Embedded processor is resetting, or is
powered up, and is booting the embedded
firmware.
Hardware Failure: If a hardware failure
occurs, the status LED indication will be
interrupted every three seconds with a
solid red indication. For example, if the LED
is blinking green when a hardware failure
occurs, the LED will
alternate between blinking green and solid
red at three-second intervals.
F
Reset
Resets the network.
Hold the Reset Button for 5 seconds while
powered Onto clear network settings. Status
LED will rapidly blink red when reset is
complete.
G
Digital Audio In
Digital optical audio inputs (TOSLINK).
Supports up to 192kHz/24-bit digital audio
in; PCM stereo format only.
Ethernet
ResetStatus
Digital Audio
In
IRRS232
GND
TX
RX
GND
TX
RX
2
1
-
1
+
-
2
+
-
3
+
100-240 V~ 50-60 HZ 2.2A
IP Audio Soundbar
GFE
DC
BA