Sawyer ACCUWRAP II User manual

Sawyer Manufacturing Company
7799 S. Regency Dr., Tulsa, OK 74131 USA
F 918.834.0318
[e-mail]
We appreciate your business!
Congratulaons on your new SAWYER product. We are proud to
have you as our customer and will strive to provide you with the best
service and reliability in the industry. This product is backed by our
extensive warranty and world-wide service network. To locate your
nearest distributor or service agency, please contact us at the phone
number and address listed on the boom of each page.
You are in good company!
Sawyer Manufacturing Company is the world leader in the design
and manufacture of pipeline and welding equipment and has been
since 1948. Sawyer equipment has become a standard in the industry
and connues to set the benchmark for quality and durability.
This user operaon manual has been made to instruct you for the best
use and operaon of your Sawyer product. Your sasfacon with our
products is our main goal. Please read this enre manual carefully,
nong all ps, notes and warnings. Safety always comes rst.
About Us
Warranty
All products manufactured by or for Sawyer Manufacturing Company are
guaranteed against defects due to faulty workmanship or materials for twelve
months from the date of purchase.
This guarantee is limited to the repair or replacement of any parts found to be
defecve, and no other liability–expressed, implied, or conngent–is assumed.
Record the following informaon for warranty purposes:
Where purchased:________________________________________________
Purchase date:___________________________________________________
Equipment Serial #:_______________________________________________
P 918.834.2550
sawyermfg.com
V1.2
D
C
B
A
M
F
G
H
I
L
K
J
E
CAUTION: Sawyer Manufacturing oers a line of Accuwrap
machines for the purpose of protecng pipe surfaces. Ensure
that the machine is in operang order before wrapping pipe. Use
cauon when operang the Accuwrap . Do not wrap hot pipe
and keep clear from ame. Aer each use clean and store in a
warm, dry area.
! !
CAUTION
A. Right Wing
B. Take-Up Wheels
C. Drive Belt
D. Take-Up Knob
E. Belt Tension Wing-Nut
F. Pipe Roller Wheels
G. Tape Tension Knob
H. Pipe Size Wheel Adjustment Holes
I. Le Wing
J. Tape Lap Angle Wing-Nut
K. Wheel Wing-Nut
L. Handles
M. Drive Belt Tensioner
N. Tape *not included*
Note: Sawyer Accuwrap machines are
sized by the width of the wrapping tape.
They use; 2”-6” (50.8-152.4mm)
6”-12” (152.4-304.8mm)
12”-18” (304.8-457.2mm)
Any Accuwrap machine will t any size
pipe.
Accuwrap II
Manual
Model 229B
Parts Diagram N

Sawyer Manufacturing Company
7799 S. Regency Dr., Tulsa, OK 74131 USA
F 918.834.0318
[e-mail]
P 918.834.2550
sawyermfg.com
V1.2
1. Remove tension pin clip. (O, Fig. 1)
2. Pull right wing (A) free from handles. (L, Fig. 2)
3. Remove cardboard tube and insert tape.
(N, Fig. 3, Fig. 4)
4. Place right wing (A) onto handles. (L, Fig. 6)
Installation Tools Needed For Installaon*
*Not Included
Fig. 1
Fig. 3
Fig. 5
1/8” allen wrench
O
A
L
Fig. 2
A
BN
Fig. 4
Tape with Release Liner Plain Tape
Release Liner
Pipe
Tape
Tape Wrapping
Direcon
Wrapping
Direcon Pipe

Sawyer Manufacturing Company
7799 S. Regency Dr., Tulsa, OK 74131 USA
F 918.834.0318
[e-mail]
P 918.834.2550
sawyermfg.com
V1.2
5. Re-insert tension pin clip. (O, Fig 7)
6. To ghten, turn tape roll in-between le wing (I) and right wing
(A) using tape tension knob. (G, Fig. 8)
7. Adjust take-up wheels (B) to same width as tape roll. (N, Fig. 9)
Note: Use 1/8” allen wrench. (Fig. 9)
8. Peel back tape roll lm and place lm onto take-up wheels.
(Fig. 10)
Note: Use tape to keep lm in place, recommend cung o a piece
of tape for each take-up wheel. (Fig. 11)
9. Turn take-up knob to start rolling lm free from tape. (Fig. 12)
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
O
A
G
I
Installation
Note: Cigaree Wrap- Set machine on at surface, loosen lap angle wing
nut (J), see that all four wheels are seng on the at surface. Tighten lap
angle wing nut (J).
Note: Spiral Wrap- Loosen lap angle wing nut (J), raise wheel nearest the
lap angle wing nut (J) as required. The higher the wheel the greater the
lap, ghten lap angle wing nut (J). This is a trial and error adjustment
and will vary with dierent pipe sizes.

Sawyer Manufacturing Company
7799 S. Regency Dr., Tulsa, OK 74131 USA
F 918.834.0318
[e-mail]
P 918.834.2550
sawyermfg.com
V1.2
1. Take o wheel wing-nut (K) to move wheel up or down wheel
adjustment holes (H) depending on pipe size. (Fig. 13)
2. Turn tape lap angle wing nut (J) depending on the amount of
overlap wanted. (Fig. 14)
Note: The higher the le wing the bigger the spiral lap; The more parallel the
wings are the more of a straight wrap.
3. Place accuwrap machine on pipe. (Fig. 15)
4. Pull a 6”-12” secon of tape from under accuwrap and sck to
pipe. (Fig. 16)
5. Using 2 people grab handles (L) wrap pipe. (Fig. 17)
Note: For best results, wheels should never leave pipe.
6. When nished wrapping cut tape and disassemble in opposite
order of installaon. (Fig. 18)
H
K
J
Operation
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
L