SB Acoustics Rinjani Kit User manual

SB
Rinjani Kit
User Manual

1 Manual | Rinjani Kit
Technical speci!cation :
Frequency range : 42-25000 Hz +/-3 dB
Sensitivity (2.83V / 1m) :89 dB
Nominal impedance : 4©
Max SPL : 107 dB
Recommended ampli!er : 50-200 W
Cross-over frequency :3000 Hz
Speaker type : 2½-way Floor Stand
Enclosure type :Bass re"ex
Port tuning frequency :35.5 Hz
Drive Units:
- High frequency driver : SATORI TW29R (29 mm soft ring dome)
Low frequency drivers :2 x 6½” SATORI MW16P-8 (advanced midwoofer)-
Cabinet:
18 mm MDF
Dimensions (H x W x D) : 1009 x 190 x 464 mm / 45.87 x 12.41 x 20.47 inch
Net weight (pair):
abinet only : 18.49 kg / 40.76 lb- C
Full assembly : 22.42 kg 49.43 lb- /
Special Features:
- Advanced high-end drivers
- Facets on top of cabinet for reduced high frequency diffraction
- Inclined baf"e for correct time alignment of drivers
(allowing for simpler cross-over design)
- Wedge shaped inner rear walls behind midwoofer for reduced direct re"ection
- Internal bracing to reduce and distribute cabinet vibrations and
hence lower sound coloration
- Dual ports for distribution of unwanted pipe resonances
- Inclined inner bottom for reduction of standing waves
- Solid single-wiring binding posts

Manual |Rinjani Kit 2
100 95
90
85
80 75
70
65 60
55
50
45 40
40.0
36.7 33.3
30.0
26.7
23.3 20.0
16.7
13.3
10.0 6.7
3.3
0.0
dB
Ohm
20 20 50 100 200 500 1k 2k 5k 10k 20kHz
Frequency response
Response Curve :
(Blue) : on axis ( Green ) : 15° off-axis ( Red ) : 30° off-axis
------ ------ ------

Mechanical drawing (size in mm)
3 Manual | Rinjani Kit

Manual | Rinjani Kit 4

5 Manual | Rinjani Kit

Manual | Rinjani Kit 6
Damping Material Cut Pattern (Size in mm)

7 Manual | Rinjani Kit
Damping material position (size in mm)

Manual | Rinjani Kit 8
Crossover Schematic

9 Manual | Rinjani Kit
Assembling instruction
Part list (each cabinet):
- High frequency driver SATORI TW29R (sold separately).................
- Low frequency drivers 6½” SATORI MW16P-8 (sold separately).....
- Rinjani kit crossover (sold separately) ............................................
- Hex socket screw M4 x 20mm (for drivers)....................................
- Hex socket screw M4 x 30mm (for pedestal) .................................
- Countersunk screw M4 x 20mm (for terminal plate) .....................
- Wood screw 4 x 16 mm for crossover (from kit crossover) ............
- Insert nut M4 (Installed ) ..............................................................
- Stainless Terminal plate .................................................................
- Binding post .................................................................................
- Seal gasket (for terminal plate) .....................................................
- Seal gasket (for pedestal, installed on cabinet) .............................
- Port "are (installed on cabinet) .....................................................
- Port paper tube (installed on cabinet) ...........................................
- Damping .......................................................................................
- Name plate ...................................................................................
- Tweeter grill ..................................................................................
- Woofer grill ..................................................................................
Tools needed:
- Hex key 3mm size (for driver screw)
- Hex key 2.5mm size (for terminal plate screw)
- Philips screwdriver no. 2 (for crossover screw)
- Soldering iron + tin (for soldering input wire to terminal)
- Hot melt glue gun(for attaching the damping and sealing the wire hole)
1 pc
2 pcs
1 pc
18 pcs
12 pcs
4 pcs
6 pcs
34 pcs
1 pc
1 pair
1 pc
1 pc
2 pcs
2 pcs
1 pc
1pc
1 pc
2 pcs

Manual | Rinjani Kit 10
1. Take out the cabinet from
the packaging and take out
the raw damping material
from the cabinet
2. Cut the raw damping material
to 8 pcs of damping according
to the cutting pattern diagram
3. Place each damping part into
the cabinet according to position
diagram. Ad a bit of glue if needed
to hold the damping in place

11 Manual | Rinjani Kit
4. Detach the pedestal by loosen
the four screws in each corner
5. Place the crossover on top of
the pedestal, then put the input
cable towards the rear terminal
side and the speaker wire
towards the front panel

Manual |Rinjani Kit 12
6. Pass the three pair of speaker
wire through each hole in the bottom
panel of the cabinet
8. Pull out the input cable
through the terminal hole then
solder it to the binding post
terminal
7. Seal all the cable holes with
hot melt glue

13 Manual | Rinjani Kit
9. Mount the terminal panel
into the terminal hole at
the back side
10. Mount the pedestal back
to the cabinet then tighten it
by tightening all 12 screws
11. Pull the three pair of
cables through the holes in
each cabinet bracing

Manual |Rinjani Kit 14
12. Hook up the cable to the woofer
and tweeter terminal
13. Mount the driver to the cabinet
and fasten the screws