SCA PLU 382375 Service manual

SPECIFICATIONS:
Working Load Limit: 2000kg
Height Lowered: 182mm
Height Raised: 346mm
2 Piece Handle: 450mm
Base Area: 117 x 102mm

1 2
OPERATION
• TO RAISE:
1. Turn the release valve with the end of the handle clockwise until it is firmly closed before
pumping.
2. Position the jack under the load and turn the extension screw or head cap until solid
contact can be made with the load to be lifted.
3. Operate the jack handle until the head cap contacts the load. Once again, check to see
that the head cap is correctly positioned.
4. After the load is lifted to desired height. Use appropriate means (e.g. vehicle support
stands) to support the load immediately.
• TO LOWER:
1. Raise the jack to remove the vehicle support stands or other supporting object.
2. Slowly turn the release valve counterclockwise (again using the handle) no more than
ONE full turn. When under a load, the jack will lower to the original point of contact. If
the piston is still extended, push the piston down manually so that the piston is not left
exposed to rusting.
MAINTENANCE PROCEDURES
• IMPORTANT:
- Do not use brake fluid, alcohol, glycerin, detergent, motor oil or dirty oil.
- Use a good grade Hydraulic Fluid (ISO 15 or equivalent).
- Improper fluid added can cause serious internal damage to the jack rendering it
inoperative.
• TO ADD OIL:
With the head cap fully lowered and the piston depressed,
place the jack horizontally and then remove the oil filler plug
(refer to figure 1). Fill until oil is level with the filler plug hole
when the jack is upright.
• TO CHANGE OIL:
- For best performance and longest life, replace the complete oil supply at least once a
year. To drain the oil, remove the filler plug. Lay the jack with oil filler hole downward
and allow the oil to run out into a suitable drain pan. The oil will run slowly because air
must enter as the oil drains out.
- DO NOT allow dirt or foreign matter to get into the system. Replace with the proper oil
as described above.
• LUBRICATION:
Add proper lubricant oil to all pivoting sections every 3 months.
• PREVENTING RUST:
Check ram (B) every 3 months for any sign of rust or corrosion. Clean as needed by
wiping with an oil cloth. When not in use always leave the head cap (A) and ram (B) all
the way down.
WARRANTY
This product is guaranteed against defects for a period of 12 months from date of
purchase. This warranty is provided by Super Cheap Auto Pty Ltd ACN 085 395 124
(Supercheap Auto) of 751 Gympie Rd Lawnton QLD 4501 Ph [phone]. Supercheap
Auto will offer a repair, replacement product or store credit if the product is assessed as
being defective during the warranty period.
To claim under this warranty, take this product to the Front Service Desk of your nearest
Supercheap Auto store. For store locations, visit www.supercheapauto.com.au (AUS)
or www.supercheapauto.co.nz (NZ). You will need your receipt or proof of purchase.
Additional information may be requested of you to process your claim. Should you not
be able to provide proof of purchase with a receipt or a bank statement, identification
showing your name, address and signature may be required to process your claim.
This product may need to be sent to the manufacturer to assess the defect before
determining any claim. Faults or defects caused by product modification, misuse and
abuse, normal wear and tear or failure to follow user instructions are not covered under
this warranty.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Any expenses incurred relating to the return of this product to store will normally have
to be paid by you. For more information contact your nearest Supercheap Auto store.
The benefits to the consumer given by this warranty are in addition to other rights and
remedies of the Australian Consumer Law in relation to the goods and services to which
this warranty relates.

3 4
HYDRAULIC SYSTEM COMPONENTS
A. Head cap
B. Ram
C. Handle
D. Release valve
E. Oil filler plug
F. Oil reservoir
G. Screw Extension
SAFE USAGE INSTRUCTIONS
Recommendations for safe usage of the jack:
1. The jack should be used on level firm ground wherever possible.
2. It is recommended that the wheels of the vehicle be chocked and that no person
should remain in a vehicle that is being jacked.
3. No person should place any portion of their body under a vehicle that is supported
only by a jack.
4. The vehicle owner’s manual should be consulted prior to the jacking of the vehicle
and for further instructions.
IMPORTANT
Sometimes during shipment and handling, air gets trapped
in the hydraulic system causing poor performance. This will
usually happen when changing the oil. Purge any air from
the system with the head cap fully lowered and the piston
depressed, place the jack horizontally and then remove the
oil filler plug. The air will escape through the filler hole.
WARNING: DO NOT GET UNDER A
VEHICLE THAT IS SUPPORTED BY
A JACK.