SCA 362693 User manual

1000KG SCISSOR JACK
PLU 362693
OWNERS MANUAL
— Working Load Limit: 1000kg
— — Height Lowered: 115mm Height Raised: 405mm
— Meets Australian and New Zealand Standard AS/NZS 2693:2007
WARNING: READ OWNERS MANUAL
CAREFULLY FOR SAFE OPERATION.

Page 1
WARRANTY
This product is guaranteed against defects for a period of 12 months from date of purchase.
This warranty is provided by Super Cheap Auto Pty Ltd ACN 085 395 124 (Supercheap
Auto) of 751 Gympie Rd Lawnton QLD 4501 Ph [phone]. Supercheap Auto will
offer a repair, replacement product or store credit if the product is assessed as being
defective during the warranty period.
To claim under this warranty, take this product to the Front Service Desk of your nearest
Supercheap Auto store. For store locations, visit www.supercheapauto.com.au (AUS) or
www.supercheapauto.co.nz (NZ). You will need your receipt or proof of purchase. Additional
information may be requested of you to process your claim. Should you not be able to
provide proof of purchase with a receipt or a bank statement, identification showing your
name, address and signature may be required to process your claim.
This product may need to be sent to the manufacturer to assess the defect before
determining any claim. Faults or defects caused by product modification, misuse and abuse,
normal wear and tear or failure to follow user instructions are not covered under this warranty.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Any expenses incurred relating to the return of this product to store will normally have to be
paid by you. For more information contact your nearest Supercheap Auto store.
The benefits to the consumer given by this warranty are in addition to other rights and
remedies of the Australian Consumer Law in relation to the goods and services to which this
warranty relatives.
...............................................................................................
..........................................
..................................................................................................................
........................
SAFE USAGE INSTRUCTIONS
OPERATING INSTRUCTIONS
— The jack should be used on level firm ground wherever possible.
— It is recommended that the wheels of the vehicle be chocked, and that no person
should remain in a vehicle that is being jacked.
— No person should place any portion of their body under a vehicle that is supported
by a jack.
— The vehicle manufacturer ownerʼs manual should be consulted prior to the jacking
of the vehicle and for further instructions.
— Store the jack in upright position.
— Do not use if the jack appears damaged in anyway.
—
—
—
This scissor jack should be used for lifting and lowering only. The raised vehicle should be
supported on vehicle support stands before working under the vehicle.
BEFORE INITIAL USE: Lubricate all pivoting and moving points with lubricating oil and after
every 50 lifting/lowering cycles or 3 months (whichever occurs first).
.......................................

Page 2
MAINTENANCE
1. Raise the jack to remove the vehicle support stands.
2. Slowly turn the jack handle counter clockwise until the jack is returned to its lowered
position.
TO LOWER:
1. Hook the handle into the hole on the screw arm.
2. Position the jack under the load so that the head cap will load firmly and centrally.
3. Turn the handle clockwise to raise the jack until the head cap contacts the load. Once again,
check to see that the head cap is correctly positioned.
4. Raise the load to the desired height. After the load is lifted to desired height, use
appropriately rated vehicle support stands to support the load.
TO RAISE:
— Keep the jack clean and well lubricated.
— When not in use, always leave the jack in the fully lowered position.
— A visual inspection of the jack should be made before each use of the jack. The jack should be
inspected for any abnormal conditions such as cracks in the welds and damaged, bent or missing
parts. A jack showing any signs of not being in full operating condition should not be used.
— Due to the potential hazards associated with the operation of vehicle jacks, no alterations should
be made to the product.
—
—
—
2 1 3 4 5 6 7
89
10
11
12
13
PARTS LIST AND EXPLODED DIAGRAM
DESCRIPTION
Head Cap
Rivet for Head cap
Upper Arm
Collar
Bracket
Bearing
Offset Handle
Threaded Rod
Lower Arm
Inner Stay
Base
Rivet for Base
Nut
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Qty.
1
2
2
1
1
1
1
1
2
1
1
2
1

Manufactured and packaged for SRGS PTY LTD ABN 23 113 230 050
751 Gympie Road, Lawnton, Queensland 4501, Australia
MADE IN CHINA
1000KG
SCISSOR JACK
WARNING: DO NOT GET UNDER A
VEHICLE THAT IS SUPPORTED
BY A JACK.
115mm
405mm
1000kg
400mm
362693
PLU:
SPECIFICATIONS
Height Lowered:
Height Raised:
Working Load Limit:
Handle Length: