Scantool SCAN 10S User manual

Industrivej 3-9
DK-9460 Brovst
Denmark
Ph.: [phone]
Fax: [phone]
Manual
Bending Machines
SCAN 10S
SCAN 13S

2
Introduction
This manual describes a group of bending machines from Scantool A / S. The front
page shows a machine of the type SCAN 10S. SCAN 13 S has a larger working width.
EU declaration of conformity
hereby declares that
SCANTOOL Bending Machines SCAN 10-13 are manufactured in
accordance with the provisions of the European Parliament and Council
Directive 2006/42 / EC of 17 May 2006
SCANTOOL A/S
Industrivej 3-9
9460 Brovst
Denmark
www.scantool-group.com
Ph.: 98 23 60 88
Fax: [phone]

3
Table of Contents
1. TRANSPORT & HANDLING 4
1.1 TRANSPORT 4
1.2 HANDLING 4
1.3 PLACING 4
2. DIRECTIONS 5
2.1 OPERATION 5
2.2 SECURITY 7
2.3 MAINTENANCE 7
3. SPARE PARTS 8
3.1 EKSPLODED DRAWING 8
3.2 SPARE PARTS LIST 9
3.3 EXTRA EQUIPMENT 9
4. TECHNICAL DATA 10
4.1 DIMENSIONS 10
4.2 SPECIFICATIONS 10
4.3 GUARANTEE 11

4
1. Transport & Handling
1.1 Transport
SCAN 10 & 13 are delivered on a pallet with the following measures:
SCAN 10 120 x 80 x 145 cm 310 kgs
SCAN 13 170 x 80 x 145 cm 340 kgs
The bending machine is packed in protective wrapping.
1.2 Handling
The machine can be transported on the pallet without difficulty.
1.3 Placing
Mounting of 10 & 13, must take place on a firm and level ground. The machine must be
fastened to the ground by means of the four fittings which are used to fasten the
bending machine to the pallet. Both holes in the triangle sheet of the mounting piece
are applied. (see fig. 1.1).
It is important that this machine is bolted to the floor.
Before the machine is bolted to the floor the machine it is necessary to level out
the machine. It can be necessary to make adjustment with distance pieces
underneath the machine if the floor is not in level. The adjustment is necessary to
avoid the machine for twisting and then pull uneven.
Fig.: 1.1 The machine is bolted to the floor.

5
2. Directions
2.1 Operation
The operation of the SCAN bending machine is the same regardless of model,
however, are the models which have a fixed clamping limited in how much they can
bend.
Before use, folding stop (7) must be loosened. The clamping pressure is from the
factory adjusted to zero in sheet thickness. The required clamping pressure can be
adjusted by using the adjusting screws (6 until the foot pedal no. 1 can be locked at the
locking pedal. The folding beam (4) can be adjusted to the required sheet thickness by
using the handles (8) lower the folding beam to minimum sheet thickness. Check the
distance between sharp nose blade and segments by placing the folding beam in 90. If
bend above 90is required the folding beam must be lowered 25% additionally.
Crowning of the folding beam is carried out by means of the two bolts at the adjusting
bolt (5).
When bending the lock for the upper beam is released by using the pedal (1) (see fig.
1.2). Now the sheet can be entered. The upper beam is pressed down again by using
the pedal.
Fig.: 1.2 Operating the Scan Bender
1. Foot pedal with locking device
2. Bed beam
3. Segments for clamping beam
4. Folding beam
5. Crowning adjustment on the folding beam
6. Hand lever for clamping beam pressure
7. Bending stop
8. Handle for adjustment of the folding beam to the correct sheet thickness
9. Counter balance arm

6
Fig.: 2.2 Bending Crack (I)
Before the lock for the upper beam (7) is activated it is necessary to adjust the handles
(6) so it is possible to press the pedal home. Finally the handle (8) for the bending
beam (4) is adjusted, so the bending crack (see fig. 2.2) corresponds with the sheet
dimension.
Angle adjustment
Folding stop no. 7 can be adjusted for the required angle. Make a folding test and
adjust the folding stop.
Utilization of segments
It is possible to dismount one or more of the segments in the upper beam in order to
make the best possible use of the many possibilities 10 & 13 SC have. (See fig. 2.3).
Fig.: 2.3 Options of bend

7
2.2 Security
When working with the bending machines the existing safety rules must be kept to
avoid personal or material injury.
SCANTOOL 10 & 13 are constructed to be used with the equipment with which they
are delivered with. Therefore it is not recommended to make any technical
reconstructions on the machine or use any technical equipment which is not approved
for SCANTOOL 10 & 13.
It is not recommended to bend sheets which exceed the maximum sheet dimension
(please see technical specifications).
2.3 Maintenance
To secure unnecessary wear and tear the four nipples must be lubricated regularly.

8
3. Spare parts
3.1 Exploded drawing
Fig.: 3.1 Exploded drawing

9
3.2 Spare parts list
Pos.
Description
1
ADJUSTING NUT
2
CLAMPING LEAF
3
T-NUT M10
4
Segments
5
CAP SCREW M10 x 20
6
CLAMPING BLOCK
7
ADJUSTING NUT SPRING
8
FLAT WASHER 20 MM
9
GREASE FITTING 8MM
10
BUSHING
11
FLAT WASHER 30MM
12
Folding leaf hanger R
13
CAP SCREW M10 x 35
14
STOP COLLAR
15
HEX NUT 10 -1,5
16
CAP SCREW M10 -1,5 x 40
18
EXT RETAINING RING 25MM
19
Shaft for Scan
20
CAP SCREW M10 -1,5 x 30
21
EXTENTION BRACKET
22
DISC SPRING 40 x 20 x 1 x 2,4
23
ROD
24
LEVER PIN
25
Shaft
26
FOOT PEDAL
27
TREAD PLATE RUBBER
28
ROLL PIN
29
EXT RETAINING RING 10MM
30
FOOT PEDAL LOCK
31
SPRING PIN 8 x 50
32
FLAT WASHER 8MM
33
PEDAL LOCK SPRING
34
SPRING PIN 6 x 50
35
SPRING PIN 10 x 50
36
O-RING 33 x 25
37
SETBACK KNOB
38
HEX BOLT M8 x15
39
HEX NUT M20 -2,5
40
SETBACK KNOB
41
BENDING LEAF
47
DISC 10,5 x 18 x 1,6
48
BUSHING
49
GAS SPRING
50
DISC
51
SUSPENSION OF SETBACK LEFT
52
Segment bar
3.3 Extra equipment
It is possible to apply Back gauge, angle segments, flat blade (10, 15 and 20 mm).

10
4. Technical Data
4.1 Dimensions
Fig.: 4.1 Measures of Scan benders
4.2 Specifications
SCAN 10
SCAN 13
Working Length
1020 mm
1320 mm
Max. Passage
2.75 mm
2.25 mm
Bending Angle
135°
135°
A
800 mm
800 mm
B
1070 mm
1370 mm
C
1150 mm
1150 mm
Weight
310 kg
340 kg
C

11
4.3 Guarantee
If within 2 year of purchase this machine supplied by SCANTOOL A/S becomes
defective due to faulty materials or workmanship we guarantee to repair or replace the
machine or defective part or parts free of charge provided that:
The product is returned complete to one of our Service Branches or Official Service
Agents.
1. The product is returned complete to one of our Service Branches or Official
Service Agents.
2. The product has not been misused or carelessly handled and in particular has
not been used in a manner contrary to the operating instructions.
3. Repairs have not been made or attempted by other than our own Service Staff or
the staff of our Official Service Agents.
4. Documentary proof of purchase date is produced when the goods are handed in
or sent for repair.
5. Wear parts are not covered by the warranty