Scantronic 9800+ User manual

HARDWIRED CONTROL
PANEL
USER GUIDE
Scantronic
Leading the way in security
(16 ZONE)

9800+ (16 Zone) Hardwired Control Panel User Guide.
© Scantronic td. 1997
Every effort has been made to ensure that the
contents of this book are correct. However, neither the
authors nor Scantronic accept any liability for loss or
damage caused or alleged to be caused directly or
indirectly by this book. The contents of this book are
subject to change without notice.
Printed and published in the U.K.
Contents
1. Introduction 3
The 9800+ (16 zone) System ........ 3
The Keypad ................................... 3
About This Guide ...........................
2. Everyday Operation 6
How Do I Know if the System is
Working? .................................. 6
Setting the System ........................ 6
Timed Final Set .............................. 6
Exceeding the Exit Time ........... 7
Final Door Set ................................ 7
Exit Terminate Button Set ............... 7
Part Setting..................................... 8
Instant Set ................................ 8
Keys itch Setting ........................... 8
If the System Will Not Set .............. 8
Unsetting the System .................... 9
Unsetting From a Keys itch .......... 9
Unsetting From the Keypad ........... 9
If You Exceed the Entry Time ... 9
3. After an Alarm 10
Fire Alarm .................................... 10
Disarming the System ................. 10
Resetting the System .................. 10
Customer Reset ............................11
Remote Reset ...............................11
4. Special unctions 12
Introduction.................................. 12
Omitting Zones ............................ 12
Omitting 24 Hour Zones ............... 13
Setting the Time and Date ........... 13
Access Codes ............................. 14
Duress Code ................................ 14
Changing Access Codes .............. 14
Using the Log .............................. 1
Table 1. Log Event Codes ............ 15
Table 1 (Cont'd) . Log Event Codes
16
Turning the Chime On/Off............ 16
Testing the System ...................... 16
Bell Test ........................................ 16
Walk Test ...................................... 17
5. System aults 18

496247 Issue 4 3
1. Introduction
The 9800+ (16 zone) System
The 9800+ (16 zone) system comprises a control unit, one or more keypads,
and various detectors.
The control unit is a steel box that houses the main controller, power supply,
stand-by battery, and any remote communicator. The control unit is normally
fitted out of sight in a safe place (for example under the stairs).
The detectors are installed at various places, or zones, around the premises.
If something triggers a detector then it signals back to the control unit. How
the control unit reacts depends on whether the system is set or unset.
When set the system raises an alarm whenever a detector is triggered. The
alarm might be a bell or strobe on the outside of your premises, or it might be
a silent signal over the telephone line to a central monitoring station. When
unset the system does not raise an alarm if a detector is triggered.
The system provides three different setting Levels, labelled A, B, and C.
Level A sets the whole system, protecting all of the premises covered by the
alarm system. Levels B and C set part of the system, protecting part of the
premises while the rest is in use. The system raises an alarm when a detec-
tor belonging to a set Level is triggered. The Installer programs the Levels
during installation. Ask your Installer to tell you which zone is allocated to
each Level.
Your premises may be fitted with 24 hour zones and panic alarm zones. If
these zones are triggered the system will raise an alarm whether or not any
Level is set.
The Keypad
From the keypad you can set and unset the system, read the event log, and
make minor changes to the way the system operates.
You must enter an access code before the system will accept commands
from the keypad. The system can store up to 8 different access codes,
providing secure access for 8 users.
Figure 1 below shows the keypad in detail.

4 496247 Issue 4
Figure 1. 9800+ Keypad
The keypad has the following displays and controls:
A, B, C LEDs These LEDs (Light Emitting Diodes) glow to show
which Level is set. The LEDs are dark when the
Levels are unset. Note that the installer can pro-
gram the system to hide the display.
Day LED The Day LED glows when the system is unset. The
LED goes dark when the system is set. Note that
the installer can program the system to hide the
display.
Fault LED The Fault LED glows when the system is in alarm,
if the system has detected a fault on the telephone
line, or if the internal battery has failed.
Service LED The Service LED glows when the panel needs an
engineer to reset it, or the system has detected an
internal problem. Call your alarm installer.
Power LED The Power LED glows when the system is using
mains power. If the Power LED flashes slowly then
the mains power has been disconnected and the
system is running off the stand-by battery.
LED Display The system displays information and instructions
through the two character LED display.
1. Introduction
2 digit Light Emitting
Diode (LED) Display
Optional programmable
panic alarm keys. Press
keys 1 and 3 together
Omit and Clear keys
Le els LEDs (Set or
Unset)
Le el setting keys
Power

496247 Issue 4 5
Level Setting Keys Use these keys to set individual Levels. A sets the
whole system. B and C set part of the system. (D is
not active.) Note that you will have to use your
access code first.
Panic Alarm Keys Press keys 1 and 3 together to raise a personal
attack alarm. (Check with your Installer that your
system is programmed with this function.)
3 (Clock) Press 3 to change the time and date stored in the
system.*
4 (Code) Press 4 to change access codes.*
(Log) Press to read a record of events that have
occurred on your system.*
7 (Chime) Press 7 to switch the Chime function on or off.*
8 (Bell test) Press 8 to start a bell test.*
9 (Walk test) Press 9 to start a walk test.*
X (Omit) The X key (Omit on 9800 keypads) lets you omit
(bypass) zones when setting the system. Note that
the Installer must program individual zones so that
the system will allow you to bypass them.
y (Clear) The y key (Clear on 9800 keypads) tells the
system that you have finished entering an access
code (or other command).
* (see "4. Special Functions")
About This Guide
The rest of this guide tells you how to use the system in more detail:
2. Everyday Operation Describes how to set and unset the system.
3. After an Alarm Tells you how to switch off the sounders after an
alarm, how to see what caused the alarm, and how
to reset the system so that it can be used again.
4. Special Functions Tells you how to use the more advanced features
of the system.
. System Faults Tells you what to do if the alarm system reports a
fault.
1. Introduction

6 496247 Issue 4
2. Everyday Operation
There are several different ways of setting the system. For all methods (except
using a Keyswitch) you must enter your access code at the keypad. The
Keyswitch method uses a key in a special switch fitted to your premises.
"Setting the System" below describes each method. Ask your Installer to
provide the method that suits your site best.
During installation the Installer programs the system to create an exit route
for your premises. When setting the system you must follow this route to
leave the premises. Similarly you must follow a specified entry route when
going into the premises in order to unset the system. If you stray from these
routes you may cause a false alarm.
How o I Know if the System is Working?
The Power LED always glows when the mains power is present. If the Power
LED flashes slowly then mains power is off, and the system is working from
its internal battery. If the Power LED is dark then the system is dead.
When the system is set, a Level LED glows to show which Level key was
used. When the system is unset, the Day LED glows. However, the Installer
can program the system to hide these displays. Ask your installer how the
system is set up.
If you wish to test the system and its detectors, see "4. Special Functions -
Testing the System".
Setting the System
Timed Final Set
With Timed Final Set the system sets after a programmed exit time has
expired. Ask your Installer to make sure the exit time is long enough for you
to leave the premises and close the final door.
1. Close all doors and windows.
2. Key in your access code at the keypad.
3. Press the appropriate Level key.
The exit time starts when you press the Level key. During the exit time
the Level LED flashes and the keypads give a continuous exit tone to
warn you that the timer is running.
If you hear an interrupted tone from the keypads or internal sounder
then one of the detectors is operating. The keypad shows the zone
number of the detector. Make sure that all doors and windows are
closed.

496247 Issue 4 7
4. Leave via the designated exit route. Close the final door.
At the end of the exit time the system sets, and stops the exit tone. The
Level LED glows steadily to show which Level is set.
Note: If you change your mind about setting the system either press y (Clear) within
five seconds of entering your code, or key in your access code again if you
miss the first five seconds.
Exceeding the Exit Time
If you do not close the final door before the end of the exit time then the
system gives an alarm and does not set. You can cancel this false alarm by
entering your access code at the keypad immediately.
When you have cancelled the alarm you will have to reset the system and
restart the setting procedure.
Final oor Set
With Final Door setting the system sets when you close the last door. There
is no fixed exit time.
1. Close all doors and windows.
2. Key in your access code at the keypad.
3. Press the appropriate Level key.
The keypad starts the continuous exit tone and the Level LED flashes.
4. Leave via the designated exit route and close the final door.
Exit Terminate Button Set
In Exit Terminate Button setting the system completes setting after you press
a button mounted outside the premises by the final door.
1. Close all doors and windows.
2. Key in your access code at the keypad.
3. Press the appropriate Level key.
The keypad starts the continuous exit tone and the Level LED flashes.
4. Leave via the designated exit route. Close the final door.
. Press the exit terminate button.
The exit tone stops and the system sets. The Level LED glows steadily.
Note: The Installer may have programmed your system to set after a fixed time even
if you do not press the exit terminate button. This is to make sure your
premises are protected even if you forget to press the exit terminate button.
sk your Installer how your system is set up.
2. Everyday Operation

8 496247 Issue 4
Part Setting
The Installer may have programmed your system so that you can protect part
of the premises while the rest is in use. Level keys B and C can give two part
set areas, ask your installer which areas each key covers.
1. Close doors and windows in the protected area.
2. Key in your access code at the keypad.
3. Press the Level key B or C as necessary.
The keypad starts the continuous exit tone and the Level LED flashes
(see "Instant Set" below).
4. Leave via the designated exit route and if necessary close the final door.
The exit tone stops and the system sets. The Level LED glows steadily
to show which Level is set.
Note: Some Levels on your system may be programmed for Silent Set. When
setting these Levels the system does not give any tones from the keypads or
internal sounder.
Instant Set
The area protected by a part set system may not need an exit route or final
exit door. For these areas the Installer may program the Level key protecting
the area as Instant Set. With Instant Set the system sets as soon as you
press the Level key. Note that Instant set is only available on level keys B
and C.
Keyswitch Setting
1. Close all doors and windows. The Ready lamp on the keyswitch should
be glowing to indicate that all the detectors are closed. (Some types of
keyswitch do not have lamps.)
2. Turn the keyswitch to "Set".
3. Leave the premises and close the final door.
The system sets.
If the System Will Not Set
If you try to set the system while a detector in the protected area is reporting
an open door or window then the keypad will give an interrupted tone and the
display will show the zone number of the detector.
1. Enter your access code at the keypad.
The interrupted tone stops and the Day LED glows.
2. Go to the zone shown on the display and find out what is triggering the
detector. If possible remedy the fault.
2. Everyday Operation

496247 Issue 4 9
3. Return to the keypad and set the system again.
If no other detectors are active the system sets.
4. Repeat steps 1 to 3 if the display shows other zones.
. If you still cannot set the system then call the engineer.
Unsetting the System
Unsetting From a Keyswitch
Turn the keyswitch to OFF. The system unsets immediately.
Unsetting From the Keypad
The system has a programmed entry time. Ask your Installer to make sure
the entry time is long enough for you to enter by the designated entry route,
get to the keypad and unset the system.
The entry time starts when you open the designated entry door. During the
entry time the keypads give a "galloping" entry tone to warn you that the
timer is running.
1. Enter through the designated entry door and go to the keypad.
As you enter the premises the system starts the entry timer and the
keypad gives the entry tone.
2. Key in your access code at the keypad.
The entry tone stops. The system is now unset.
WARNING: If you enter your premises and an internal alarm
starts then there may be an intruder.
If You Exceed the Entry Time
If you regularly have problems exceeding the entry time, ask your installer
about "Dual Ply Entry" and "Alarm Abort".
If the system is programmed for Dual Ply Entry, then the control unit adds a
30 second grace period to the end of the Entry Time. During that grace
period the keypads give a high pitched continuous tone to warn you that the
Entry Time has run out.
When programmed for Alarm Abort the system gives you 90 seconds after
the end of the Entry Time to cancel any alarm caused by exceeding the Entry
Time or leaving the entry route. If you exceed the 90 second Alarm Abort
time then the panel gives a full alarm, and you may have to call an engineer
to reset your system.
2. Everyday Operation

10 496247 Issue 4
3. After an Alarm
3. After an Alarm
When your system raises an alarm you must disarm it in order to switch off
the sounders and strobes. The system keeps a record of which zone(s)
triggered the alarms, and shows the zone number(s) on the keypad display.
Once you have disarmed the system, the system must be reset before you
can start using it again.
Fire Alarm
The system gives a fire alarm by sounding a warbling tone from the keypads
and alarm sounder. The display shows the letters "Fr".
1. Evacuate the premises and call the Fire Brigade. Do not attempt to
unset the alarm.
2. When the premises are safe, follow the instructions below.
isarming the System
1. Go to the keypad via the entry route.
2. Key-in your access code.
The sounders go quiet, the Day and Fault LEDs glow, and the display
shows the letter "c" with the zone number of the first detector to be
triggered. You may also see the Service LED glowing.
3. Establish the cause of the alarm.
4. Carry on to reset the system.
Resetting the System
There are three different methods for resetting. You can tell which method
your system uses by looking at the Service LED after an alarm.
 If the Service LED is dark then the system uses Customer Reset.
You can reset the system yourself from the keypad.
 If the Service LED glows after an alarm then your system uses
Engineer Reset. Call your alarm company and ask for an engineer
to visit the premises to reset the system.
 If the Service LED glows after an alarm and your system is con-
nected to a central monitoring station then your system may use
Remote Reset. Your alarm company will give you instructions over
the phone and a special code so that you can reset the system
from the keypad.

496247 Issue 4 11
3. After an Alarm
Customer Reset
1. Key-in your access code and press y (Clear).
The Fault LED goes dark and the display clears.
2. You can now use your system as normal.
Remote Reset
Before starting this process, make sure you have a pen and paper to hand.
You will need to write down some information shown on the keypad. If you
have not carried out a remote reset before, read the instructions through
before starting.
1. Key in your access code.
The display shows "rr" (reset required).
2. Press y (Clear).
The display shows "- -", indicating that the system wants further instruc-
tions.
3. Press "6".
The display shows two pairs of numbers alternately. The two pairs of
numbers make a four digit Control Code.
4. Write down the four digit Control Code. Note that the system will display
the control code twice and then return to showing the first detector to
alarm. If you miss the Control Code repeat steps 1 to 3.
. Contact your alarm company central station.
The central station will ask a few questions to make sure you are who
you say you are. They will then ask for the circumstances of the alarm,
and for the Control Code. If they do not need to send an Engineer to
check the system they will give you a "Reset Code".
6. Key in the Reset Code on the keypad.
The display clears and the Fault and Service LEDs go out.
7. You can now use your system as normal.
Note: Your alarm company may use "RedCare Reset". sk your installer for more
information about this form of reset.

12 496247 Issue 4
4. Special Functions
Introduction
You can perform a number of other functions, apart from setting and unsetting
the system. These functions are:
[Access code] + X Setting the system so that some zones are by-
passed or omitted.
[Access code] + 3 Setting the time and date on the system's internal
clock.
[Access code] + 4 Changing access codes.
[Access code] + Reading the system log.
[Access code] + 7 Turning the chime function on or off.
[Access code] + 8 Testing the sounders.
[Access code] + 9 Testing the zones.
To use these functions you must key in your access code and then press a
number key. The rest of this section describes each function in turn.
Omitting Zones
Your system may be programmed so that you can omit individual detectors
when setting the system. Ask your Installer which zones can be omitted. Note
that omission is not permanent. You must omit the zone every time you set
the system.
To set with a zone omitted:
1. Key in your access code.
2. Press the appropriate Level key, and then within seconds:
3. or zones 1 to 9 press X (Omit) followed by the number(s) of the
zone(s) you want to omit (for example, key in X(Omit) 2 to omit zone 2).
or zones 10 to 16 press X (Omit) twice followed by a number 0 to 6
(for example, key in X (Omit) X (Omit) 2 to omit zone 12).
The display shows the zone number of the detector that will be omitted.
The system carries on to set as normal. The system will not raise an
alarm if the omitted zone is triggered. Note that the next time you set the
system the zone will operate as normal; omission only lasts for one
setting/unsetting cycle.

496247 Issue 4 13
4. Special Functions
Omitting 24 Hour Zones
If your system is fitted with 24 hour detector zones, you may be able to omit
them if necessary. For example, your premises may have a fire door that you
occasionally open. Ask your Installer if this is possible.
If your system is programmed to allow you to omit a 24 hour zone, then:
1. Key in your access code.
2. or zones 1 to 9 press X (Omit) followed by the number(s) of the
zone(s) you want to omit (for example, key in X(Omit) 7 to omit zone 7).
or zones 10 to 16 press X (Omit) twice followed by a number 0 to 6
(for example, key in X (Omit) X (Omit) 2 to omit zone 12).
To reinstate a 24 hour zone:
1. Key in your access code.
2. Press X (Omit) followed by y (Clear).
Setting the Time and ate
The control unit contains an internal clock/calendar that runs as long as there
is power present (mains or stand-by battery). The system uses this clock to
mark the time and date on the system log. If the power supply fails for any
reason, and the stand-by battery is low, then the system loses track of the
correct time and date. You may also need to change the time if you live in an
area that uses summer/winter time.
Note: You need the access code for User 1 in order to change the time and date.
To set the time and date:
1. Key in User 1 access code.
2. Press 3.
The display shows "yy" for the year.
3. Key in two digits for the year followed by y (Clear).
The display shows "oo" for the month.
4. Key two digits for the month (01 for January, to 12 for December)
followed by y (Clear).
The display shows "dd" for the day
. Key in two digits for the day, followed by y (Clear).
The display shows "hh" for the hour
6. Key in two digits for the hour followed by y (Clear). (Use the 24 hour
clock.)
The display shows "ii" for the minutes.

14 496247 Issue 4
4. Special Functions
7. Key in two digits for the minutes, followed by y (Clear).
To view the time when the system is unset:
1. Enter User 01 access code.
2. Press 3 followed by y (Clear).
The system displays two digits for the year.
3. Press y (Clear) repeatedly to see, in order, the month, day, hour, and
minutes.
Access Codes
The system can store up to 8 different user access codes. For security you
should give one code to each person who has responsibility for setting and
unsetting the system. Do not allow users to share codes.
Every time someone enters an access code on the keypad the system
records the event in its log. To distinguish all the users and keep their access
codes hidden, the log shows each user as a number, for example "User 02",
"User 03" and so on.
When delivered from the factory all access codes are set to default numbers.
User 01 default access code is "1234". You should change this immediately
to a code that only you know.
User 02 default access code is "X 002", User 03 is "X 003" and so on up to
User 08 (X 008). However, the default access codes for these users cannot
set or unset the system, or use any of its special functions. (On older key-
pads use the OMIT key in place of the X key.)
uress Code
If your system is connected to a central monitoring station, you may want to
give some of the users a Duress Code. If a user enters the Duress Code
while the system is set, then the control unit unsets the system, but at the
same time sends a silent alarm call to the central monitoring station. This
facility is designed for times when a user is being forced to unset the alarm
system by an intruder.
When the control unit is delivered from the factory the Duress code is "X X X
X (OMIT, OMIT, OMIT, OMIT)". This code is inactive until you change it.
Changing Access Codes
1. Enter User 01 access code.
The display shows "- -".
2. Press 4.
The display shows "oc" (old code)

496247 Issue 4 15
4. Special Functions
3. Key in the access code you wish to change.
The display shows "nc" (new code).
4. Key in the new access code that you wish to use.
Note: Do not use 0 (zero) as the first digit of the code.
. Press y (Clear) to store the new code.
Using the Log
The system keeps a log of the last 2 6 events. You can examine this log
from the keypad. To use the log:
1. Key in your access code.
2. Press .
The display shows the user number belonging to the access code you
used.
3. Press 1 to see earlier events in the log. Press 3 to see more recent
events.
The display shows a two character code for each type of event. Table 1
on the next page shows each of the codes that you might see, and their
meaning.
4. Press y (Clear) twice to stop using the log.
Table 1. Log Event Codes
Code Meaning
AA Arm area A (full set)
Ab Arm area B (part set)
Ac Arm area C (part set)
AE Installer access
AP Auxiliary power failure
bF Battery fault
c1 to c16Zone violation
cc Communication successful
cF Communications failure
dA Disarm area A
db Disarm area B
dc Disarm area C
E1 to E16Entry via zone circuit
EA Entry alarm
EF Exit fault
Lb Low battery
Lf Telephone line failure P.T.O.

16 496247 Issue 4
4. Special Functions
Table 1 (Cont'd) . Log Event Codes
Code Meaning
Lt Control unit lid tamper
o1 to o16Zone omitted
P1 to P4 Remote keypad dual key PA alarm
PF Mains power failure
PL Print log.
r1 to r4 Remote keypad enclosure tamper
rP Remote keypad missing
rr Installer reset
rt Remote keypad excess key presses tamper
S1 to S16Zone soak Test
Sr System reset
St Set time
t1 to t16Zone tamper violation
tr Tamper return fault
u1 to u8 Access user (u9 = Duress, u0 = keys witch)
 When showing zones 10 to 16 the display alternates between the letter 'c'
and the number of the zone.
Turning the Chime On/Off
Your system may be programmed so that a chime tone sounds whenever
certain doors are opened while the system is unset. If your system has an
Exit Terminate button, then it will act as a door bell while Chime is on. To turn
Chime on or off:
1. Key in your access code.
The display shows "_ _ "
2. Press 7 followed by y (Clear).
Testing the System
Bell Test
You can test that the internal and external sounders, and the strobe, are all
working as follows:
1. Key in your access code.
The display shows "_ _ "
2. Press 8.
The system turns the external sounder, strobe, internal sounder(s) and
keypad sounders on for three seconds each, one after the other.
3. Press y (Clear) to finish the test.

496247 Issue 4 17
4. Special Functions
Walk Test
You can set the system so that it will allow you to walk round the premises
and test each of the detectors (a walk test). Choose a time when the
premises are empty to carry out the test, otherwise people may trigger any
movement detectors before you do, and confuse the results of the test.
If any detector fails the test then call your alarm company and ask them to
check the system.
Note: If your system is fitted with 24 hour or personal attack detectors, you cannot
walk test them. If you wish to test them call your alarm company.
1. Key in your access code.
The display shows "_ _"
2. Press 9.
The display shows "- - " then "C" and the zone number of any
detector(s) that are already triggered.
3. Walk round your premises and trigger each detector in turn (except 24
hour or personal attack detectors). As you trigger a detector the keypad
and internal sounder give a short tone, and the display shows the zone
number.
4. Press y (Clear) twice to stop the test when you have triggered all the
detectors.
Note: You can abandon the test at any time by pressing y (Clear) twice.

18 496247 Issue 4
5. System Faults
Your system may light the Fault LED and start an internal alarm to indicate
that it has detected a fault. (An internal alarm is the keypad and internal
sounders active, but the external sounder (bell) and strobe quiet.) The display
will give a two letter code to indicate what type of fault has occurred. The
table below shows the more common faults that can happen.
Display code ault
Lf Telephone line fault. Enter access code to silence
the sounder. Enter your access code again. If the
display clears the fault was temporary. If the display
still shows Lf then the telephone line is not working.
Contact your alarm company. Note that you may
still be able to set the system, but it will not be able
to report any alarms to the central monitoring
station until the telephone line is repaired.
bF Battery fault. Enter your access code to silence the
sounder. Contact your alarm company immediately.
You cannot set the system until the fault is cleared.
Lb Battery Low. Enter your access code to silence the
sounder. Contact your alarm company immediately.
You cannot set the system until the fault is cleared.
Sr Total power failure. Enter your access code to
silence the alarm. At some time both mains and
battery power failed together. Contact your alarm
company immediately. You cannot set the system
until the fault is cleared.
"t" plus number. Tamper. Enter your access code to silence the
alarm. Something or someone has interfered with
the system. Contact your alarm company immedi-
ately. You cannot set the system until the fault is
cleared.
If the display shows any other code, see Table 1 on pages 13 and 14 for
more details.

496247 Issue 4 19
ENOZNOITPIRCSED ELOHW METSYS )A(
TRAP BTES TRAP CTES TIMO DEWOLLA EMIHC
1
2
3
4
5
6
7
8
9
01
11
21
31
41
51
61
noitaruDlleB
teseRreenignE
dettiFrotacinummoC
emittixE
emityrtnE
APdapyeK
Day contact Tel:
Night contact Tel:
Company Name:

20 496247 Issue 4