Sceptre LCD Monitor User manual

i
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device ma not cause harmful interference, and
2. This device must accept an interference received, including
interference that ma cause undesired operation.
FCC WARNING
This equipment has been tested and found to compl with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequenc energ
and, if not installed and used in accordance with the instructions, ma
cause harmful inerference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined b turning the
equipment off and on, the user is encouraged to tr to correct the
interference b one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution:
To compl with the limits for an FCC Class B computing device, alwa s
use the shielded signal cord supplied with this unit.

ii
The Federal Communications Commission warns that changes or
modifications of the unit not expressl approved b the part responsible
for compliance could void the user’s authorit to operate the equipment.
CE mark for Class B ITE (Followin European standard EN55022/1998; EN61000-
3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11)
Radio Frequency Interference Statement
Warnin :
This is a Class B product. In a domestic environment, this product ma
cause radio interference in which case the user ma be required to take
adequate measures.
Canadian Doc Notice
For Class B Computin Devices
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulation of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la class B
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada."

iii
TABLE OF CONTENTS
TABLE OF CONTENTS...........................................................................................III
Your New LCD Monitor 1
Unpackin 1
Identifyin Components 3
Adjustin the Tiltin An le 5
Connectin AC Power and Video Cable 6
Power Mana ement System 6
How to install the VESA mount 7
The LCD Monitor's Control Panel 8
Adjustin the Monitor’s Display 9
TFT LCD Monitor Specifications 14
Supported Timin 16
Troubleshootin 17

1 Rev.1
The LCD Monitor
Your New LCD Monitor
Your LCD Monitor has been designed to be versatile, ergonomic and
user-friendl . The LCD Monitor is capable of displa ing most
standards, from 640x400 VGA to 1280x1024 SXGA. The digital
controls located on the front panel allow the user to easil adjust the
Monitor’s displa parameters, and the LCD Monitor’s small footprint
gives ou more room in our workspace for other peripherals.
Lightweight and compact, the LCD Monitor is the perfect solution for
users on the go. You can use the LCD Monitor for ever thing from
making business presentations to pla ing computer games. The
Monitor also has a wall-mountable stand for added convenience.
The architecture of the LCD Monitor incorporates an LCD panel that produces a clear displa
with low radiation emission. And with its low power consumption, the LCD Monitor helps ou
reduce our power bill.
Unpackin
Before unpacking our LCD Monitor, prepare a suitable workspace for our LCD Monitor and
computer. Look for a stable, level and clean surface near a wall outlet. Even though the
LCD Monitor uses ver little power, ou should put it in a location which allows sufficient
airflow to ensure that the LCD Monitor and our computer do not overheat. Set up our LCD
Monitor so that the panel is not facing a window where sunlight often comes in. The glare
caused b sunlight reflecting off of the LCD Monitor’s screen will make it difficult to use the
Monitor for viewing.
Note: Using a computer for an extended period of time with a poor workstation
set-up and incorrect working habits can cause health problems. The science of
ergonomics studies the relationship between health and a suitable working
environment. There is a section on ergonomics at the end of this chapter. For
more information on ergonomics, contact your nearest computer bookstore, or
local library. The Internet also has information on this and other sub ects.

2 Rev.1
After unpacking our LCD monitor, make sure the following items are included
in the box and are in good condition:
• LCD monitor
• Power Cord
• Monitor-To-PC Analog signal cable 15pin
• 1.5M stereo Jack Audio Cable
• User’s manual
If ou find that an item to be missing or appear to be damaged,
contact our dealer immediatel . Do not throw awa the packing
material or shipping carton in case ou need to ship or store the LCD
monitor in the future.

3 Rev.1
Identifyin Components
A. The LCD Monitor — Front View
Figure 1-1: The LCD Monitor Front View
1. Power-On Indicator
This Circular LED indicator green lit when the power is on and
orange lit when the LCD monitor is in power-saving mode.
2. Monitor Stand
3. LCD Screen
The LCD monitor screen is a 19-inch TFT 1280 x 1024 screen.
4. LCD Monitor Control Panel
Refer to Chapter 2 for more details.
3
4
1
2
1
3
2
1
4

4 Rev.1
B. "Hot Keys" for Quick Adjustment of Monitor Settin s
Figure 1-2: "Hot Ke s"
1. Brightness adjustment "hot ke ":
Press button to allow ou to adjust
the brightness from high, Mid and low
brightness of the LCD Monitor directl .
A small “High Brightness” Charactes is
also displa ed.
Hi h Bri htess
Mid Bri htess
Low Bri htness
2. Volume Adjustment “ Hot Ke :
Press
 &  two buttons to allow ou
to adjust the speaker volume directl
without enabling OSD screen.
50
- +

5 Rev.1
C. The LCD Monitor — Rear View
VGA
AC-IN AUDIO
Figure 1-3: LCD Monitor Rear View
1. AC Power Jack
2. VGA Cable With 15-Pin D-Sub VGA Connector
3.
Stereo Audio Jack
Adjustin the Tiltin An le
The LCD Monitor’s angle settings range from 0° to 15°.
15
Figure 1-4: Tilting the Monitor
0 to 15

6 Rev.1
Connecting AC Power and Video Cable
Note: Turn off our PC and the LCD monitor before connecting our LCD monitor to the
computer.
D-SUB
AC-IN
AC Outlet
(Wall Socket)
Computer Power Cord
Figure 1-5: The AC Adapter
Power Mana ement System
This LCD Monitor complies with the VESA DPMS power management proposal.
When the LCD Monitor is in power-saving mode or detects an incorrect timing, the monitor
screen will be blank and the power LED indicator starts blinking.
Audio cable

7 Rev.1
How to install the VESA mount:
Please see the below drawing.
First, find the slide on the stand.
Push the slide to the right side as step 2
Rotate the stand and let the stand horizontall as panel.
Now you will find the 4 holes to fix the VESA 100mm mount.

8 Rev.1
The Display Controls
The LCD Monitor’s Control Panel
Figure 2-1: The Control Panel
1. Menu: OSD Menu button
Press this button to displa the OSD (On-Screen Displa ) menu.
2. : Bri htness settin hot key
This button lets ou set the LCD brightness to the preset value
from High, Mid to Low three level.
3. Adjustment button  &
These buttons let ou move horizontall across our settings or
selections, or change the setting value..
4. :Power Switch
This button lets ou turn power for the LCD monitor ON or OFF.

9 Rev.1
Adjustin the Monitor’s Display
OSD Main Menu
1. Pressing the OSD Menu button causes the screen below to appear.
2. Use the  & ke to select the desired group, then press Menu ke
to the sub-menu
3. Repeat step 2 to select the changed item, then press Menu to select the changed item.
4. Press the  & ke to change the value.
5. Press Menu ke to retuen the item 3 screen to do another adjustment
The OSD Main Menu
OSD Main SCREEN
Timing : 1280 x 1024
V/H Freq : 74.6Hz 79KHz
DCLCD DCL9A+

10 Rev.1
Auto Adjust Option
The Auto Adjust option lets the monitor determine and
select the settings that are most appropriate for our
s stem requirements.
Provides ou with the current displa timing information.
Brightness and Contrast Adjustment
Adjusts the Brightness value
Adjusts the Contrast value
Execute the white balance function
Return to the previous Menu
Audio Function
Volume : Adjust the speaker volume
Mute : Mute the speaker
Return
Color Temperature Adjustment

11 Rev.1
Set up the color temperature value
User Mode
Sets the color temperature to 6500K
Sets the color temperature to 9300K
Red change Red gain for the color temperature
(onl valid when color temperature set at user mode )
Green change Green gain for the color temperature
(onl valid when color temperature set at user mode )
Blue change Blue gain for the color temperature
(onl valid when color temperature set at user mode )
Return to the previous Menu
Displa Qualit Adjustment
Auto Adjust: use this option to appl automaticall setting
Changes the screen viewing size

12 Rev.1
Adjusts phase tracking to reduce displa flicker
Moves the whole screen right or left
Moves the whole screen up or down
Return to the previous Menu
OSD Adjustment
Restores settings to factor default values
Sets the OSD timer
Moves the OSD menu horizontall
Moves the OSD menu verticall
Set the graphic mode or text mode
Return to the previous Menu
Exit the OSD screen

13 Rev.1
Note:
1) No video
When the monitor is ON and there is no video signal received,
the following message will be displa ed
2) Signal out of range
When the frequenc range of the signal is out of the Monitor’s specifications, (over 85HZ) the
displa will show the following message
Out of Ran e

14 Rev.1
Appendix A
TFT LCD Monitor Specifications
LCD Panel 19" SXGA
Control
Functions
Power
Software Power switch with LED indicator
(ON/OFF)
Main Menu Submenu
Information
Brightness
/Contrast Control
Brightness/Contrast/White balance/Exit
Audio Control Volume/Mute/Exit
Color temperature
Control
User mode, 9300K, 6500K
R,G,B, gain value
Displa Qualit Auto Adjustment/Phase
adjustment/Screen Size/ Screen
Horizontal position/Screen Vertical
position/Exit
On-Screen
Displa
(OSD)
OSD adjsutment Restore to the default/OSD timer/OSD
Horizontal Position/OSD Vertical
Position/640&720/Exit
Displa Area
(mm)
376.32 x 301.056
(19" diagonal)
Displa
Colors
16 M
Video
Interface
VGA Compatible Analog RGB

15 Rev.1
Scanning Frequenc
H/V, Hz
24-80K
50-75
Power Management Meets VESA DPMS
Power Consumption
(ON/OFF, W)
37W/1W Max.
Dimensions
WxHxD
16.5 x 16.48 x 6.53
in.
(419 x 418.4 x 166mm)
Net Weight
(approx.)
12.7
lbs
(5.8 Kg)
Power Suppl Universal Input AC Socket
Environment Operating Temperature: 32 to 104°F (0 to 40° C)
Relative Humidit : 10% to 90%
Regulator FCC B DoC,UL/cUL,Energy star

16 Rev.1
Appendix B
Supported Timin
Item Standards Resolution Dot Clock
(MHz)
Vertical
Scannin
Frequency
(Hz)
Horizontal
Scannin
Frequency
(kHz)
1 NEC PC98 640x400 21.05 56.42 24.83
2 MAC 13" mode 640x480 30.24 66.67 35.00
3 MAC 16" mode 832x624 57.28 74.55 49.73
4 MAC 17" mode 1024x768 80.00 75.02 60.24
5 VGA 640x350 25.18 70.09 31.47
6 VGA 640x400 25.18 70.09 31.47
7 VGA 640x480 25.18 59.94 31.47
8 VESA 640x480 31.50 72.81 37.86
9 VESA 640x480 31.50 75.00 37.50
10 VESA 800x600 36.00 56.25 35.16
11 SVGA 800x600 40.00 60.32 37.88
12 VESA 800x600 50.00 72.19 48.08
13 VESA 800x600 49.50 75.00 46.88
14 VGA 720x400 28.32 70.09 31.47
15 XGA 1024x768 65.00 60.00 48.36
16 VESA 1024x768 75.00 70.07 56.48
17 VESA 1024x768 78.75 75.03 60.02
18 VESA 1280X1024 108 60 63.98
19 VESA 1280X1024 135 75 80
*Once a mode is optimized, there is no need to make an further adjustment
as long as the VGA card remains unchanged.
*Specifications are subject to change without notice.