SCG SKR600 User manual

Before After
Product Overview The picture is for reference only.
Please check the actual model for specific functions.
Exterior plate
(Outside view)
Interior plate
(Inside view)
Setting Button
Up Button：
Use it to add new keycards/
PIN codes
Down Button：
Use it to delete keycards/
PIN codes
Battery Cover
Use the special tool provided
to open
Sensor
Keypad
PIN codes consist of 4~8
digits numbers can be
repeated
Confirm/Exit Button
Select Button
Keyhole Cover
Horizontally position the
key and turn the keyhole
cover 90 clockwise to
remove it then unlock with
the key
--Accessories--
Emergency Override Key
3 keys provided per lock RFID Keycards
Door Lock Status
Type
Administrator
User
Single-Entry User
Volume
Quantity Function No. Instruction
4 sets
94 sets
1 set
1 set
Add/Modify/Delete
Unlock the door
Can be used only
once
Sound volume
Unlocking Keycards or PIN codes.
Keycards or PIN codes be used
only once.
Types of No.
Status
Operation Successful
Operation Failed
Enter/ Exit Setup Mode
Low Battery
Door Opened Indication
Door Closed Indication
Light
Blue
Red
Blue / Red
Red
1 beep
3 beeps
2 beeps
5 continuous beeps
Sounds
1 beep after the right Keycard or PIN code that the lock is open.
After depressing the lever, the door is locked 1.5 seconds after
the lever comes back to the horizontal position.
Unlocking Methods
Notice
．The factory default admin. PIN code is 123456. It is highly recommended to change the
code upon installation of the lock.
．Only one PIN code or one Keycard can be set per No. of location.
．Please turn to the last page to restore to the factory default settings.
．There is no need to reset after battery replacement with the memory function.
•It can’t enter the setup mode during passage mode.
1.Mechanical Key : Horizontally position the key and turn the keyhole cover 90 degrees
clockwise to remove it then unlock with the key.
2.Keycard : Press any button to enter the system, simply place the RFID card to the sensor.
3.PIN Code : Press any button to enter the system, enter assigned PIN code and press
to confirm.
4.Passage Mode : Place the RFID card to the sensor or enter assigned PIN code and press
. Press to lock.
＃
＊＃ ＊
＃
00~03
＊
04~97
＊
98
＊
99
＊
Electronic RFID & Keypad Door Lock
SKR600
Operation Manual
SKR600 Specification
Dimension -- Panels：
290(H) x 70(W) x 72 (D)-(mm)
Approximate Weight：4520 g
Use 4AA Alkaline batteries (1.5V)
(not included)
Others：
RFID Sensor
Digital Pad (Metal & Waterproof)
Door Thickness：
45mm ~ 55mm
56mm ~ 80mm
Standard US Mortise Lockbody
Temperature：-10 C ~ 70 C

Enter the Setup Mode
Enter the
Setup Mode
Administrator Recognition
Administrator
＊
Press the No. 00~ 99
＊
Press
the No.
Enter
Exit Setup Mode
Exit Setup Mode
PIN Code/ RFID Keycard Setup
1. The admin. and user PIN code cannot be 000000/111111/123456.
2. Blue light flashes if the NO. has been setup.
Notice
3. 3 beeps (red light) mean failed operation.
4. The system exit setup mode without any action over 5 seconds, two beeps (blue light).
User Setup
1345
2＃
Press the Up Button on
the back of the lock for 2
seconds until hear two
beeps.
Input admin. PIN code and
then press to confirm or
position the admin. card to
the sensor.
＃04 ~ 97
＊＊
Press the No. Enter the intended PIN
code (consistsof 4-8 digits),
and then press to
confirm or position the card
to the sensor.
＃
Single-Entry User Setup
Other Setup
User Deletion
1 2 3 4
＃
Press the Down
Button on the
back of the lock
for 2 seconds
until hear two
beeps.
Input admin. PIN
code and then
press to confirm
or position the
admin. card to the
sensor.
＃
Enter the No. you
intend to delete
( 01 ~ 97),
and then press
to confirm or
position the card.
＃
＊＊
Volume Setup
1 2 3 4 5
＃
Press the Up
Button on the
back of the lock
for 2 seconds
until hear two
beeps.
Input admin.
PIN code and
then press
to confirm or
position the
admin. card to
the sensor.
＃
Press
the No.
99
＊
Press
00(mute),
01(low),
02(medium) or
03(loud), and
then press
to confirm.
＃
1 2 3 4
All User Deletion
＃
Press the Down
Button on the
back of the lock
for 2 seconds
until hear two
beeps.
Input admin. PIN
code and then
press to confirm
or position the
admin. card to the
sensor.
＃
Press the Down
Button on the back
of the lock for 5
seconds until hear
a continuous beep
and two short beeps
mean successful
reset.
Factory Default Setting
Problem
Continuous beeps after successful
operation
No reaction when entering Keycards/
PIN codes
Light doesn’t go off
Low battery alert. Replace the battery
immediately.
Battery is dead. Please use the key to
unlock.
Consecutive Keycards/PIN codes entry
errors. Pleae try again after 1 minute.
Replace batteries.
Indication
Troubleshooting
Important Notes
1345
2＃
Press the Up Button on
the back of the lock for 2
seconds until hear two
beeps.
Input admin. PIN code and
then press to confirm or
position the admin. card to
the sensor.
＃Press the No. 98
＊
Enter the intended PIN
code (consistsof 4-8 digits),
and then press to
confirm or position the card
to the sensor.
＃
Administrator Setup
- First time setup
1345
2＃
2
Press the Up Button on
the back of the lock for 2
seconds until hear two
beeps.
Input the factory default
admin. PIN code (123456)
and then press to
confirm.
＃
Input admin. PIN code and
then press to confirm or
position the admin. card to
the sensor.
＃
00/ 01
02/ 03
＊＊
＊＊
Press the No. Enter the intended admin.
PIN code (consists of 4-8
digits), and then press
to confirm or position the
admin. card to the sensor.
＃
- Admin. already setup
1. Remove one battery.
2. Next, while continuously pressing the two buttons on the back, reinstall the
battery.
A continuous beeps (red light) and a short beep (blue light) after successful
operation.
1. If the card is losing, please delete right away.
* Notice：The administrator (*00) can’t be deleted individually.
2. Please use alkaline batteries only.
3. To preserve the cleanliness of the product, wipe it down using a clean cloth.
Do not use alcohol or other chemical agents.
4. Please handle the lock carefully to ensure normal operation.
5. If you encounter any problem, please refer to the user manual first. If you still
have questions, please feel free to contact us or email us.
Enter the Intended PIN
Code or Card
Recognition
Enter the
Setup Mode
Administrator Enter Exit
Setup Mode
Recognition