Schlage LINK FE599 User manual

Package Contents
Pin Wrench
AA Batteries (4)
Alternate Faceplate
Cover
Cover
Screws (2)
Lever
Strike
Latch
Keypad
Baseplate
Key
Latch/Strike Screws (4)
Keypad Lock
Installation Instructions
Model FE599
P516-405
Important Information
You will need
this code
information to
perform certain
functions using
the lock keypad.
These are the
factory default
lock code
settings (see
Step 1).
Lock Programming Code
six (6) digits
User Code A
four (4) digits
User Code B
four (4) digits
Tools Needed
Phillips
OR
Web Support:
http://monitoringcontrol.verizon.com
1 Locate Programming Code and Preset User Codes
The programming code and the preset
user codes are printed on the yellow
stickers located on the back of the keypad
and/or on the installation sheet that came
in the box. Write these codes in the space
provided on the first page.
Please go to http://monitoringcontrol.
verizon.com and follow the simple steps
provided in the online setup wizard.
This will enable you to add your Door
Lock device to the Home Monitoring and
Control Network.
Programming Code XXXXXX
User Code A xxxx
User Code B xxxx
S/N x-xxxxxxxx
Model FE599
ProgrammingCode XXXXXX
UserCode A xxxx
UserCode B xxxx
S/Nx-xxxxxxxx
ModelFE599
2 Check Door Dimensions
If your door does not match the dimensions shown, go to
http://verizon.schlage.com for instructions on how to prepare
your door.
2¹⁄₈” (53 mm)
Hole
2³⁄₈” (60 mm)
O
2³⁄₄” (70 mm)
3 Install Strike Into Frame
(2)
Strike Screws
4 If Necessary, Change Latch Faceplate
Check edge of door to determine the type of faceplate required.
OR
5
5
5 Install Latch
Latch must be flipped so that bevel faces toward door jamb.
OR
Jamb Jamb
(2)
Latch Screws
Bevel
6 Remove Sticker from back of Lock
P515-804 Rev.08/07
¹⁄₈"¹⁄₄"
0
¹⁄₈"–¹⁄₄"
(3–6mm)
7 Install the Keypad
Feed the cable under latch assembly as shown below. Then
slide the tailpiece through the hole as shown below.
Tailpiece

©2011 Ingersoll Rand
Printed in U.S.A.
P516-405 Rev. 09/11-b
8Adjust Hands-free Post
The hands-free post is the threaded stud on back of lock. It’s
purpose (in step 10) is to attach the lock and baseplate together
so that the lock will hold itself on the door.
Hands-free post may need to be adjusted with a screwdriver to
the dimensions shown below.
¹⁄₈"− ¹₄"
(3 mm - 6 mm)
Hold keypad
against door
Adjust with
screwdriver
so screw
extends
beyond door
edge.
Hands-free
post
9 Feed Cable through Baseplate
Feed the cable through the hole as shown below. DO NOT
connect the cable at this point.
10 Slide Baseplate onto Door over Hands-free post
Hands-free post should lock plate against door surface. If
hands-free post does not lock plate onto door, see step 8 for
adjustment.
Hands-free post
11 Connect the Cable
Snap the connectors together.
12 Install Batteries and Battery Cover
13 Install Cover and Lever
If the lever does not snap into place easily, you may have to tap
the lever with a hammer using a piece of wood to cushion it. Be
careful not to damage the finish of the lever. See step 14 on the
next page to verify that the lever is handed correctly to match
your door.
(2)
!
Tuck wires into open space
on baseplate. Be careful not
to pinch any wires between
cover and baseplate.
Cover Screws
14 Check Handing of Lever
a
d
c
b
Incorrect
See steps below
to change lever
handing
Correct
Go to step 15
15 Test Locking and Unlocking from Inside
Test with
door open!
To lock, press button.
Press
Red = locked
To unlock, press button.
Press
Green= unlocked
16 Test outside entry (when door is locked)
Test with
door open!
Unlock Did latch retract and
then extend?
Yes. Lock is installed
correctly.
No. Latch retracted but
did not extend (latch
bound). Check step 7.
No. Nothing happened.
Check steps 11 and 12.
1. Find User Code A (written on
the first page, see step 1).
2. Enter User
Code A (four
digits) into
the keypad.
3. Rotate and
then release
lever.
17 Configure your system
After you finish the door lock installation, please go back to
the setup wizard at http://monitoringcontrol.verizon.com to
complete the configuration process.
If Lock Removal is Required
Hands free post must be disengaged to prevent damage to lock.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications to this equipment not expressly approved
by Schlage could void the user’s authority to operate the equipment.
FCC ID: P2GFE599 IC: 7954A-FE599