Schmid RAPID Secure XL User manual

Operation instructions
RAPID®Secure XL (screw-in tool)
www.schrauben.at1|09/22
Technical data:
Power tool adapter Hex type 11,5 (for 13 mm standard-chuck)
Max. lenght (incl. Bit) x diameter 207 mm x 46 mm
Weight 680 g
Bit adapter Hex type 5/16”
Maximum torque 130 Nm
Drive shaft (1)
Holding element (4)
Bit (3)
Front clamping screw (5a)
Adjusting screw - inside (6)
Rear clamping screw (5b)
Protrusion length L
Power tool adapter (2)
Bit: T40 | 50 mm lenght - 5/16” Bit: T 50 | 50 mm lenght - 5/16”
Suitable screws Bit-protrusion length L Suitable screws Bit-protrusion length L
ø 8 mm Rapid®/GPR®washer head 25.5 mm ø 10 mm Rapid®/GPR® countersunk head 28.0 mm
ø 8 mm Rapid® SuperSenkFix 25.5 mm ø 12 mm Rapid®/GPR® countersunk head 28.0 mm
ø 12 mm Rapid® Dual 25.5 mm ø 10 mm Rapid®SuperSenkFix 28.0 mm
ø 12 mm Rapid® T-Lift 25.5 mm
Scope of application:
The RAPID®Secure XL screw in tool was designed for quick, safe and
effortless installation of long timber construction screws with a rotary
drill.
The RAPID®Secure XL screw-in tool allows safe overhead and angled
screwing. The screw’s head is reliably fixed in the screw-in tool and
results in longer life of the bits.
• First familiarize yourself with the operating instructions for RAPID®
Secure XL and the power tools you are using.
• The user alone is liable for damage caused by improper use.
• The generally accepted rules and regulations for the prevention of
accidents must be observed.
Bit setup:
• At first loosen both clamping screws (5) slightly and remove the
inserted bit.
• Clamp the power tool adapter (2) and loosen the axial adjusting
screw (6) using a 3 mm allen key (picture A).
• Adjust the desired protrusion length L and fix the bit with the
clamping screws (5). Start tightening the front clamping screw (5a).
• After fastening the first 100 operations, tighten the clamping screws
(5) again.
A

Operation instructions
RAPID®Secure XL (screw-in tool)
www.schrauben.at2|09/22
Safety instructions
Observe the following to avoid personal injury and property damage:
• Ensure safe footing.
• Only use hand-operated power drills without permanent arrestors
and the matching grip.
• Hold the machine with both hands.
• Wear personal protective equipment (hearing protection, protective
goggles, protective gloves etc.).
• The screw-in tool RAPID®Secure XL is suitable for a maximum
torque of 130 Nm.
• Firmly secure the RAPID®Secure XL screw in tool in the power
drill’s chuck and assure secure locking onto screw head.
Troubleshooting
BCDE
F G H
Work instructions
Put the screw onto the bit, slide the holding element (4) forward, thus
locking the screw head (picture B + C).
The screw should firm fit in the RAPID®Secure XL, that means it do
not tumble or have too much axial play. If this is not the case, look for
the possible cause and its correction under „Troubleshooting“.
Assure the screw head is securely locked. Check the outer sleeve:
it must not protrude beyond the end of the holding element (4), see
picture D + E.
Screw in the screw vertically or at any angle. You don’t need to apply
axial pressure onto the screw once you have locked the screw head.
You only need to maintain the torque.
Once the RAPID®Secure XL screw-in tool contacts the working sur-
face the holding element (4) automatically releases the screw head.
Now it allows a clear view on the screw head location (picture G + H).
After releasing the screw head apply axial pressure onto the screw.
Screw in until the screw head has reached the desired depth.
Care and maintenance
• Once you are done with your work, clean the RAPID®Secure XL
screw in tool without any liquids.
• Store it clean and dry.
• Regularly lubricate moving parts with dry lubricant.
Service
• Repairs may only be performed by professional staff.
• If there are any malfunctions with the RAPID®Secure XL, please
contact your local account manager.
Trouble Possible cause Correction
The RAPID®Secure XL screw in
tool cannot be locked onto the
screw head
Clamping screw (5) is protruding
beyond surface of drive shaft (1) tighten clamping screw (5)
Check screw type Only use the listed screw-types
Check bit type Only use the listed bit-types
The balls do not reach over the screw
head
reduce the bit protrusion L until the balls slide completely over the
screw-head
Bit works its way out of screw
head, despite lock
Screw head has too much play Correct axial position of the bit, increase protrusion L
Check screw type Only use the listed screw-types
Check bit type Only use the listed bit-types
The screw tumbles strongly and
does not guide well
Screw head has too much play Increase the protrusion L until there is little to no more play bet-
ween the screw head and the balls
Check screw type Only use the listed screw-typesn
Check bit type Only use the listed bit-type