Scientific Industries MULTIPLATE GENIE SI-4100 User manual

MULTIPLATE GENIE is a trademark of Scientific Industries
© Scientific Industries Inc. 2022
LTP0093 Rev-
SI-4100
SI-4101
SI-4102
SI-4103
North American
(Type B)
No Plug
(C14 Socket)
Euro
(Type F)
UK
(Type G)
Supplied 4 microplates
Speed Approx. 750-3200 RPM (60Hz), 750-2700 RPM (50Hz)
Maximum Load 0.5 Kg (1.1 lbs)
Pulse ON/OFF 1 sec - 99 minutes or continuous
Timer - Hands Free 1 sec - 99 minutes or continuous
Dimensions (D x W x H) 383 x 261 x 152mm (15.1 x 10.3 x 6.0 in)
Weight 5.9 Kg (13.0 lb)
Environmental 0°C - 38°C (32°F-100°F), 95% Humidity max
Electrical 120-240V, 1.5 Amps, 47-63 HZ
SPECIFICATIONS
SI-4104
SI-4105
SI-4106
Swiss
(Type N)
Japan
(Type B)
Australia
(Type I)
Markings/Warranty CE / 2 Years
If this equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Caution
Unplug from power before cleaning. Do not immerse.
Do not position the equipment so that it is difficult to disconnect the power cord.
Care and Handling
Specifications
Your MULTIPLATE GENIE should be given the care normally required for any electrical
appliance. Unplug unit and wipe housing with damp cloth and detergent. Blot any spills
immediately.
The MULTIPLATE GENIE is classified as “Installation Category 2”, “Overvoltage Category
2” and “Pollution Degree 2”. Indoor use only in elevation up to 2000m of altitude.
TM
TM
TM
1.0 mm (.039 in) diameterVortexing Orbit

scientificindustries.com
TM
MULTIPLATE GENIE
TIMED MICROPLATE MIXER
OPERATING INSTRUCTIONS
®
Models SI-4100 through SI-4106

(min) (rpm)
ON
OFF START
STOP
PULSE
(min) (rpm)
PULSE
Set Time
Up/Down
Press to enter
PULSE settings
Pulse
Settings
Set Speed
Up/Down
Press
START/STOP
to Begin
2.3
2.1
1.0
Timed Operation
(Time until stop)
Power On
(min) (rpm) (min) (rpm)
Set Time
Up/Down
Press to enter
PULSE settings
Set Speed
Up/Down
Press
START/STOP
to Begin
2.2
Continuous
Operation
(Non-Timed)
(min) (rpm) (min) (rpm)
2.5
Error
Fault Detected
When Displayed
Unplug to Clear Error
Plug In to Restart
1
2
(min) (rpm) (min) (rpm)
2.4
Sleep
(After 10 min
of inactivity) Press Any Key
to Wake
(min) (rpm) (min) (rpm)
Set Pulse
ON time
Press PULSE
Again to Set
-or-
START/STOP
to Begin
Set Pulse
OFF time
4
2 3
Press to enter
PULSE settings
1
(min)
(min)
(min)
1/10th sec.
1 sec.
1 min.
(min) (rpm) (min) (rpm)
Set Time
Up/Down
Set Speed
Up/Down
Press
START/STOP
to Begin
5 6
7
ON
OFF START
STOP
PULSE
PULSE
ON
OFF START
STOP
PULSE
PULSE
ON
OFF START
STOP
PULSE
PULSE
ON
OFF START
STOP
PULSE
PULSE
ON
OFF START
STOP
PULSE
PULSE
ON
OFF START
STOP
PULSE
PULSE

Install
Microplates
and optional
Microplate
Tray Support
3.0
1
2
3A
3B
3C
4
5
6
7
8
Parts List
4.0
EL-4100-575
EBP0002
0K-0400A-905
0K-0401A-905
0K-0405A-905
0K-4100-100
PP-4000-401
HWP0045
0M-4000-201
ESP0011
Digital Overlay
Digital Timer Board
Motor 120V Assembly, Digital
Motor 230V Assembly, Digital
Motor 100V Assembly, Digital
Housing w/ screws, kit
Rubber Feet
Bumpers
Mat
Optical Sensor
PART No. DESCRIPTIONITEM No.
4
6
7
8
9
(A - G)
2
3
(A - C)
4
5
1
9A
9B
9C
9D
9E
9F
9G
10
318-0510-02
0K-0246-901
0K-0256-901
0K-0266-901
0K-0276-901
0K-0286-901
ECP0021
Not Supplied with Unit
PP-4000-400
120V Line Cord
230V Line Cord, without Plug
230V line cord, European Plug
230V Line cord, British Plug
230V Line cord, Swiss Plug
100V Line cord
Australian Plug (only)
4 Tray Support (add on part)
PART No. DESCRIPTIONITEM No.
12
2
1