Scotsman 300 lb Cube Ice Machine C0322 User manual

Installation Manual
Manuale di installazione
Manual de instalación
Manuel d’installation
Installationsanleitung
C0322
C0522
C0330
C0530
C0630
C0830
C1030

Introduction
The design of this modular cuber is the result of
years of experience and testing. Standard features
include front accessible indicator lights and on-off
switches that provide the user with fast access to
critical information and easy operational control. .
Keep this manual for future reference.
This installation manual is divided into three main
sections: Installation, which provides the trade
person with the information needed to set up and
install this product; Use and Operation, which
provides the user with the information to use the
product; and Maintenance, which provides the user
with the information needed keep it operating
efficiently.
Note any Caution or Warning symbols when they
appear on the product or in this manual. They
indicate potential hazards.
July 2007
Page 1
C0322 through C1030
Air and Water Cooled Installation Manual
Table of Contents
Introduction ........................................... Page 1
Installation: Product Specifications ............................... Page 2
Model Number Description ................................... Page 3
Water .............................................. Page 4
C0322 and C0522 Cabinet Layout ............................... Page 5
C0330, C0530, C0630, C0830 and C1030 Cabinet Layout ................... Page 6
Panel Removal ......................................... Page 7
Plumbing Requirements ..................................... Page 8
Electrical ............................................. Page 9
Initial Start Up .......................................... Page 10
Adjustments ........................................... Page 11
Use and Operation........................................ Page 12
Control Switches......................................... Page 13
Options ............................................. Page 14
Cleaning, Sanitation and Maintenance ............................. Page 15
What to do before calling for service .............................. Page 16

Installation: Product Specifications
Location Limitations:
The product is designed to be installed indoors, in
a controlled environment. Air cooled models
discharge very warm air into the room out the back.
Space must be allowed at the left side and back for
air intake and discharge. Water cooled models
discharge warm water into the building’s drain.
Space needs to be provided on both sides and
above for service access.
Space Limitations
Note: Although the machine will function, ice
capacity of air cooled machines will be significantly
reduced with minimal clearance at the sides, back
and top. Some space is recommended for service
and maintenance purposes on all models.
150mm of space at the sides and back are required
for adequate operation. To get the most capacity,
locate the machine away from heat producing
appliances and heating ducts, and keep the left
side away from any wall, allow 300-450 mm of
space for good air flow
Airflow is in the left side, out the back (as viewed
from the front).
Environmental Limitations
Minimum Maximum
Air
temperature 10oC. 38oC.
Water
temperature 5oC. 38oC.
Water
pressure 1 bar 5 bar
Power supply – acceptable voltage ranges
Minimum Maximum
230 volt model 207 volts 253 volts
Power Cord Reference Table
Rated Current of Model
Nominal
Cross-Sectional Area
(mm2) of Conductors
3,1 through 6 amperes ,75
6,1 through 10 amperes 1,0
10,1 through 16 amperes 1,5
16,1 through 25 amperes 2,5
Warranty Information
The warranty statement for this product is provided
separately from this manual. Refer to it for
applicable coverage. In general warranty covers
defects in material or workmanship. It does not
cover maintenance, corrections to installations, or
situations when the machine is operated in
circumstances that exceed the limitations printed
above.
Product Information
The product is a modular cuber. That type of
machine is designed to be placed on an ice
storage bin or an ice dispenser. Many installations
only require the matching bin, but some also
require an adapter to be placed between the bin
and the cuber or between the dispenser and the
cuber. This product cannot be stacked. See the
chart for application information.
July 2007
Page 2
C0322 through C1030
Air and Water Cooled Installation Manual
Air Flow

Model Number Description
Example:
•C0322SA-6A
•C= cuber
•03= nominal ice capacity in 100s of pounds
•22= nominal width of cabinet
•S= Cube size. S=small or half dice cube.
M=medium or full dice cube
•A=Condenser type. A=air cooled. W=water
cooled
•-6=230 50 Hz
•A=Series revision code. A=first series
Note: In some areas of this manual model numbers
may include only the first five characters of the
model number, meaning that the cube size,
condenser type and voltage differences are not
critical to the information listed there.
Options:
There are several field-installed options that can be
installed at initial start up or later. They include:
•Adjustable ice level system.
•Advanced feature board.
Some installations require bin or dispenser
adapters. See the table below.
Standard Bin Applications - Adapter
information.
Model
BH360,
or B222
or B322
B530P,
B330P,
B530S,
HTB555
or
BH550
BH800,
BH801,
B842S
BH900,
B948S
C0322,
C0522 Direct fit KBT27 Not available
Not
available
C0530,
C0630,
C0830,
C1030
Does
not fit Direct fit KBT28 KBT22
Hotel Dispensers
The HD22 and HD30 are compatible with this ice
machine, no adapters are needed.
•HD22 – use with C0322 or C0522
•HD30 – use with C0330 or C0530
Note: All models ship with the On and Off switches
front accessible. If desired, the On and Off
switches can be covered but by changing the bezel
in the front panel’s trim strip. A cover-up bezel
ships loose with the machine.
* Adjustable ice level control option recommended
for these applications.
Other Bins & Applications:
Note the drop zone and ultrasonic sensor locations
in the illustrations on the next pages.
Scotsman ice systems are designed and
manufactured with the highest regard for safety
and performance.
Scotsman assumes no liability of responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any part and/or other components not
specifically approved by Scotsman.
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and design are subject to change
without notice.
July 2007
Page 3
C0322 through C1030
Air and Water Cooled Installation Manual

Water
The quality of the water supplied to the ice machine
will have an impact on the time between cleanings
and ultimately on the life of the product. Water can
contain impurities either in suspension or in
solution. Suspended solids can be filtered out. In
solution or dissolved solids cannot be filtered, they
must be diluted or treated. Water filters are
recommended to remove suspended solids. Some
filters have treatment in them for suspended solids.
Check with a water treatment service for a
recommendation.
RO water. This machine can be supplied with
Reverse Osmosis water, but the water conductivity
must be no less than 10 microSiemens/cm.
Potential for Airborne Contamination
Installing an ice machine near a source of yeast or
similar material can result in the need for more
frequent sanitation cleanings due to the tendency
of these materials to contaminate the machine.
Most water filters remove chlorine from the water
supply to the machine which contributes to this
situation. Testing has shown that using a filter that
does not remove chlorine, such as the Scotsman
Aqua Patrol, will greatly improve this situation,
while the ice making process itself will remove the
chlorine from the ice, resulting in no taste or odor
impact. Additionally, devices intended to enhance
ice machine sanitation, such as the Scotsman
Aqua Bullet, can be placed in the machine to keep
it cleaner between manual cleanings.
Water purge
Cube ice machines use more water than what ends
up in the bin as ice. While most water is used
during ice making, a portion is designed to be
drained out every cycle to reduce the amount of
hard water scale in the machine. That’s known as
water purge, and an effective purge can increase
the time between needed water system cleaning.
In addition, this product has the capability to
automatically vary the amount of water purged
based on the purity of the water supplied to it. The
water purge rate can also be set manually.
Adjustments of purge due to local water conditions
are not covered by warranty.
July 2007
Page 4
C0322 through C1030
Air and Water Cooled Installation Manual

C0322 and C0522 Cabinet Layout
September 2008
Page 5
C0322 through C1030
Air and Water Cooled Instalation Manual
PLAN VIEW
22" PRODIGY
24.00 REF.
61
22.00 REF.
55.9
2.00
5.1
2.00
5.1
19.05
48.4
3.25
8.3
10.25
26
7.00
17.8
ICE DROP OPENING
ULTRASONIC
BIN LEVEL
SENSOR
(OPTIONAL)
Top View
LEFT SIDE VIEW
24.00
61
LOUVER AND
REMOVABLE FILTER
AC UNITS ONLY
C0322, C0522 Air Cooled Side View
AIR COOLED
BACK VIEW 1.43
3.6
1.62
4.1
3.04
7.7
10.79
27.4
14.56
37
1.60
4.1
3/4" FPT
DRAIN
.88" DIA
ELECTRICAL
ACCESS
Water Inlet
3/8” FPT - 60 Hz
3/4 Gas - 50 Hz
C0322, C0522 Air Cooled Back View
Note: Top number is centimeters, bottom number is inches.

AIR COOLED
BACK VIEW
3.06
7.8
10.81
27.5
14.59
37
1.48
3.7
1.73
4.4
1.70
4.3
3/4" FPT
DRAIN
.88" DIA
ELECTRICAL
ACCESS
Water Inlet
3/8” FPT - 60 Hz
3/4 Gas - 50 Hz
C0330, C0530, C0630 AC Back View
LEFT SIDE VIEW
24.00
61
LOUVER AND
REMOVABLE FILTER
AC UNITS ONLY
C0830, C1030 Air Cooled Side View
C0330, C0530, C0630, C0830 and C1030 Cabinet Layout
September 2008
Page 6
C0322 through C1030
Air and Water Cooled Installation Manual
PLAN VIEW
24.00 REF.
61
30.00 REF.
76.2
2.00
5.1
2.00
5.1
19.05
48.4
3.25
8.3
10.25
26
7.00
17.8
ICE DROP OPENING
ULTRASONIC
BIN LEVEL
SENSOR
(OPTIONAL)
Top View - All
LEFT SIDE VIEW
24.00
61
LOUVER AND
REMOVABLE FILTER
AC UNITS ONLY
C0330, C0530, C0630 Air Cooled Side View
Note: Top number is centimeters, bottom number is inches.

Installation
This manual covers several models. The model
number on the product is located in two places, on
the back dataplate and on the model and serial
number tag, located behind the front panel. See the
illustration for the dataplate and serial tag locations.
Write the model and serial number of this product
here:
________________________________________
Write the day, month and year of initial start up
here:
________________________________________
Switch Bezel
All models ship with the On and Off switches front
accessible. If desired, the On and Off switches can
be covered up to prevent unauthorized use by
changing the bezel in the front panel’s trim strip. A
cover-up bezel ships loose with the machine.
To change bezels: Remove the front panel, and
refer to the instruction label on the inside of the
front panel. Push snaps of standard bezel in and
pull the bezel out of the front panel trim strip.
Locate other bezel. Push into the trim strip from the
front until it snaps into place. Return the front panel
to its original position and secure it to the cabinet.
Uncrate and Set Up
Begin with unpacking the ice storage bin. Remove
the carton, and using part of the carton as a
cushion, tip the bin on its back to remove the skid
and attach the legs or casters.
Return the bin to an upright position. Check the bin
top gasket for gaps and tears, fill any in with food
grade sealant prior to placing the ice machine on
the bin.
Install the bin top adapter or ice dispenser adapter,
if one is required for the application.
If the ice machine has not been unpacked, do so
now. Remove the carton from the skid. Lift the ice
machine off the skid directly onto the bin.
Note: The machine is heavy! Use a mechanical
hoist if necessary.
Secure the ice machine to the bin with the
hardware provided (two metal straps and 4 bolts).
Place the bin and ice machine in the selected
location and level it by adjusting the bin leg
levelers.
Plumbing Requirements
All models require connection to cold, potable
water. A hand actuated valve within site of the
machine is required. Air cooled models have a
single 3/4 gas BSPP inlet water connection.
Water cooled models have the same inlet fitting
plus an additional 3/8” FPT condenser inlet water
connection.
Water Filters
If connecting to water filtration, filter only the water
to the reservoir, not to the condenser. Install a new
cartridge if the filters were used with a prior
machine.
All models require drain tubing to be attached to
them. Air cooled models have a single ¾” FPT
drain fitting in the back of the cabinet. Water cooled
models have the same fitting plus an additional ½”
FPT drain fitting in the back of the cabinet.
Install new tubing when replacing a prior ice
machine, as the tubing will have been sized for the
old model and might not be correct for this one.
1. Connect water supply to water inlet fittings.
3/8" OD tubing is recommended.
2. Connect drain tubing to drain fittings.
3. Route the drain tubing to building drain. Follow
local codes for air gap.
Drain Tubing:
March 2007
Page 7
C0322 through C1030
Air and Water Cooled Installation Manual
Warning: All models require connection to
potable water.

Use rigid drain tubes and route them separately –
do not Tee into the bin’s drain and, if water cooled,
do not Tee the condenser drain into the reservoir
or bin drain.
Vent the reservoir drain. A vertical vent at the back
of the drain, extended about 200-250 mm will allow
the gravity drain to empty and also keep any
surges during draining from discharging water out
the vent..
Horizontal runs of drain tubing need a 20 mm fall
per meter of run for proper draining.
Follow all applicable codes.
Electrical
The machine is not supplied with a power cord, one
must be field installed. Select the power cord
based on the power draw requirements of the
model being installed.
The dataplate on the back of the cabinet details the
power requirements, including voltage, phase, and
maximum fuse size. Extension cords are not
permitted. Use of a licensed electrician is
recommended.
Electrical connections are made inside the junction
box in the back panel of the ice machine.
Power Cord Installation:
1. Select and obtain the proper power cord of type
H03RT-F, H05RR-F, H03VV-F, H03VVH2-F or
heavier. Ground wire must be green/yellow color.
Only one cord per plug. See Power Cord
Reference Table for suggested cord sizing.
2. Electrical supply circuit must be dedicated to this
machine. Do not connect to a circuit powering any
other device. Product should only have one supply
means.
3. Remove the junction box cover.
4. Install a field supplied, non-detachable,
non-metalic strain relief per code. Strain relief must
be properly sized for the OD of the power cord and
the ID of the routing hole.
5. Route the power cord through the access hole /
strain relief and properly attach the power supply
wires. Do not tin the leads. Strip 6 mm of power
cord lead insulation and properly attach power cord
wires to the lead wires in the junction box.
6. Connect an electrical plug of the proper type for
the application and country of use.
Note: The plug will be the disconnect means for
this machine.
7. Attach a ground wire to the ground connection in
the junction box. Note: Ground wire must be longer
than power lead wires.
8. Check voltage when complete.
9. Return the junction box cover to its original
position and secure with the original screws.
March 2007
Page 8
C0322 through C1030
Air and Water Cooled Installation Manual
Plumbing Connections
Floor Drain
Water
Supply Water Cooled Supply
Water Cooled Shown, Air Cooled Similar
Water
Cooled
Drain
Bin Drain
Connection
Reservoir
Drain
Connection
Drain Vent
Potable
Water
Connection

The electrical disconnect switch with fuse
protection must be a two pole type with a minimum
of 3 mm between open contacts.
Follow all applicable local, state and national
codes.
Power Cord Replacement:
Notice: In case the power cable is damaged, it
must be replaced ONLY by QUALIFIED
TECHNICIANS to prevent any possible risks.
1. Disconnect electrical power to machine.
2. Remove junction box cover.
3. Disconnect and remove existing power cord.
4. Select and obtain the proper power cord of type
H03RT-F, H05RR-F, H03VV-F, H03VVH2-F or
heavier. Ground wire must be green/yellow color.
Only one cord per plug. See Power Cord
Reference Table for suggested cord sizing.
5. Install a field supplied, non-metalic,
non-detachable strain relief per code.
6. Route the power cord through the access hole /
strain relief and properly attach the power supply
wires. Do not tin the leads. Strip 6 mm of power
cord lead insulation and properly attach power cord
wires to the lead wires in the junction box.
7. Connect an electrical plug of the proper type for
the application and country of use.
8. Attach a ground wire to the ground connection in
the junction box. Note: Ground wire must be longer
than power lead wires.
9. Reconnect power supply. Check voltage when
complete.
10. Return the junction box cover to its original
position and secure with the original screws.
Final Check List
After connections,
1. Wash out the bin. If desired, the interior of the
bin could be sanitized.
2. Locate the ice scoop (if supplied) and have it
available for use when needed.
Final Check List:
1. Is the unit located indoors in a controlled
environment?
2. Is the unit located where it can receive
adequate cooling air?
3. Has the correct electrical power been supplied
to the machine?
4. Have all the water supply connections been
made?
5. Have all the drain connections been made?
6. Has the unit been leveled?
7. Have all unpacking materials and tape been
removed?
8. Is the correct switch bezel installed in the trim
strip?
9. Is the water pressure adequate?
10. Have the drain connections been checked for
leaks?
11. Has the bin interior been wiped clean or
sanitized?
12. Have any water filter cartridges been replaced?
13. Have all required kits and adapters been
properly installed?
March 2007
Page 9
C0322 through C1030
Air and Water Cooled Installation Manual
Ground Wire
Connection
Install
Strain
Relief
Power
Supply
Wires
Junction
Box
Cover
Electrical Connections, Back of Unit

Initial Start Up
1. Remove front panel. Check machine for any
packing or wires rubbing moving parts. Note
location of control board in upper left corner of
the machine’s front.
2. Remove tape securing curtain to evaporator.
3. Switch on the electrical power to the machine.
Observe that some of the control’s indicator
lights glow and its display shows O.
4. Open the water supply valve.
5. Push and release the ON button. The code
display will begin to blink F.
The purge valve opens, the water pump starts and
the inlet water valve opens to add water to the
reservoir. In a few seconds the purge valve closes
and the water pump stops. Water will flow into the
machine until the reservoir is full. The hot gas valve
and harvest assist device will activate, then the
compressor and water pump will start. If it’s an air
cooled model the fan(s) motors will begin to turn a
few moments after the compressor starts. The
display will show a continuous F. Five seconds later
the hot gas valve will close and the harvest assist
device will return to its standby position. Warm air
will be discharged from air cooled models.
6. Observe the Ready for Harvest indicator light.
It may blink early in the cycle, that is normal.
The control will ignore that signal for the first 6
minutes of freeze.
7. During the Freeze cycle move the curtain and
observe that the SW1 or SW2 light on the
control board blinks Off when the curtain
moves away from the evaporator and On when
returned to its normal position.
Note: Moving the curtain during the Freeze cycle
has no affect on control function, but will cause
water to flow into the cube chute.
8. When enough ice has frozen, the Ready for
Harvest indicator light will be on steady. After
it’s been on steady for a few seconds Harvest
will begin.
The display shows an H. The hot gas valve opens,
the air cooled fan motor(s) shut off and the harvest
assist mechanism is activated. The purge valve
opens to drain some water, when it does the inlet
water valve opens to refill the reservoir. After a few
seconds the purge valve closes but the inlet water
valve continues to fill the reservoir. Harvest
continues until the ice is released as a unit and
forces the curtain to open. When the curtain opens
it signals the controller which returns the unit to a
freeze cycle.
9. Check the ice harvested for proper bridge
thickness. The ice bridge is factory set at 1/8
inch. If needed, adjust bridge thickness. Do
NOT make it too thin.
10. Return the front panel to its normal position
and secure it to the machine.
11. Instruct the user in the operation of the
machine and its maintenance requirements.
12. Fill out and mail the warranty registration form.
Typical Ice Making Cycle Times (minutes).
Listed times are for clean machines in proper
installations. Cycle length at startup will be longer
until the system stabilizes.
Model 21oC air /
10oC. water
32oC. air /
21oC. water
C0322A 10-12 14-16
C0322W 9-11 10-12
C0522A 11-13 16-18
C0522W 13-15 13-15
C0330A 9-11 12-14
C0330W 8-10 9-11
C0530A 12-14 16-18
C0530W 10-12 11-13
C0630A 9-11 11-13
C0630W 7-9 10-12
C0830A 10-12 13-15
C0830W 11-13 12-14
C1030A 9-11 11-13
C1030W 9-11 10-12
July 2007
Page 10
C0322 through C1030
Air and Water Cooled Installation Manual

Adjustments
Bridge Thickness - For the Service Tech Only
1. Push and hold Off till the machine stops.
2. Remove evaporator cover.
3. Remove curtain.
4. Use a hex wrench and rotate the bridge
thickness adjustment screw in 1/8 turn
increments CW to increase bridge thickness.
Rotate CCW to decrease bridge thickness.
Caution: Do not make the bridge too thin or the
machine will not harvest properly. Bridge thickness
adjustments are not covered by warranty.
5. Return curtain and evaporator cover to their
normal positions.
6. Push and release the On button. Check next
harvest of ice. Repeat steps 1-6 if needed.
Water Purge Setting
The water purge is factory set to the automatic
position, suitable for most water conditions. The
setting can be changed to one of 5 manual settings
or left on automatic.
Purge
setting 1 - Minimum 2- Moderate
3-
Standard 4 - Heavy 5 - Maximum A - Automatic
Water
Type
RO water or
equivalent
Low TDS
non-RO
water
Use for
typical
water
High TDS
water
Very High
TDS water
Any with
conductivity not
less than 10
microSiemens/cm
To set:
1. Switch the machine OFF by holding the Off
button in until a number or the letter Ashows
on the display.
2. Press and release the On button repeatedly
until the number on the display corresponds to
the desired setting.
3. Press and release the Off switch again to
return to the normal control state.
July 2007
Page 11
C0322 through C1030
Air and Water Cooled Installation Manual
Bridge Thickness Adjustment Mechanism
Ice Bridge Thickness Measurement
1/8-3/16"
bridge
Adjustment
Screw
Note: Indentations may be deeper on C0322 and C0330
1/8" indentation
Too Big Too Small
Just Right
Note: Water cooled models, the refrigeration
system discharge pressure is factory set at 245
PSIG, which should yield a freeze cycle discharge
water temperature of about 40-43 degrees C.
Adjust if necessary.

Use and Operation
Once started, the ice machine will automatically
make ice until the bin or dispenser is full of ice.
When ice level drops, the ice machine will resume
making ice.
Caution: Do not place anything on top of the ice
machine, including the ice scoop. Debris and
moisture from objects on top of the machine can
work their way into the cabinet and cause serious
damage. Damage caused by foreign material is not
covered by warranty.
There are four indicator lights at the front of the
machine that provide information on the condition
of the machine.
Indicator Lights:
•Power
•Status
•Water
•De-scale & Sanitize
Indicator Lights & Their Meanings
Power Status Water De-Scale & Sanitize
Steady Green Normal Normal – bin full or making ice - -
Blinking Green Self Test
Failure Switching on or off - -
Blinking Red - Diagnostic shutdown or, if making
ice, temperature sensor failure
Lack of
water -
Yellow - - - Time to de-scale and
sanitize
Blinking
Yellow - - - In Cleaning mode
Light off No power Switched off Normal Normal
All Blinking Unit remotely locked out – check with leasing company
If the Water light is on, the machine has sensed a
lack of water. Check the water supply to the
machine. The water could have been shut off or the
water filter cartridges might need to be changed.
If the De-Scale light is on, the machine has
determined that it needs to be cleaned. Contact an
authorized Scotsman service agent and have the
machine cleaned, de-scaled and sanitized.
July 2007
Page 12
C0322 through C1030
Air and Water Cooled Installation Manual
Note: A Component Indicator Light switches ON to
indicate that the component is operating.
Note: There are two Curtain Switch lights, SW1 and
SW2. These single plate models have one curtain
switch light on all the time, as a curtain switch light
is ON when a curtain is either open or not present.

Control Switches
There is front access to two switches – On and Off.
To switch the machine OFF, push and release the
Off button. The machine will shut off at the end of
the next cycle. To shut the machine off
immediately, push and hold the Off button for 3
seconds.
To switch the machine ON, push and release the
On button. The machine will go through a start up
process and then resume ice making.
Control Options
There are three optional, field installed controls
that can be added to this machine.
•VariSmart™ adjustable ice level control
•SmartBoard™ advanced control board and
data logger
Adjustable ice level control,kit # KVS
When this option is present there is an adjustment
post and an additional indicator light to the right of
the four indicator lights mentioned above. The
ultrasonic ice level control allows the user to control
the point that the ice machine will stop making ice
before the bin or dispenser is full. Reasons for this
include:
•Seasonal changes in ice used
•Planning to sanitize the bin
•Faster turnover for fresher ice
•Certain dispenser applications where
maximum ice level is not desired
Use of control
There are several positions the ice level can be set
to, including Off (knob and label indicators lined
up), where it fills the bin until the standard bin
control shuts the machine off. See the kit’s
instructions for complete details.
Rotate the adjustment post to the desired ice level.
The machine will fill up to that level and when it
shuts off the indicator light next to the adjustment
post will be On.
Note: Ice will build up in the bin or dispenser at an
angle, the distance set will be from the sensor to
the top of the ice. The sensor position is shown in
the cabinet layout diagrams.
The actual distance between the highest point of
the ice may be closer or further away than the
distance set, depending upon the angle of the ice.
July 2007
Page 13
C0322 through C1030
Air and Water Cooled Installation Manual
Power Water On
Status De-Scale Off
02-4294-01 Rev. A.
Adjust Ice Level
L
o
w
e
r
Bin
Full
VariSmart Control Area

Options
Advanced Feature Board, kit #KSB
When this option is present there is an additional
display panel in the area below the main control
board. It is not visible when the front panel is on.
The Smart-Board’s features include:
•Seven day programmable ice level setting
when used with the optional Ultrasonic ice
level control
•Recording of machine operation, including
cycle time.
•Calculation of average cycle time
•Recall of malfunctions with the time they
occurred.
Ice
The cuber drops ice in large sections. That ice will
break up into random parts as it falls into the bin,
but some large sections may remain on top of the
ice in the bin. When removing ice, tap the groups of
ice with an ice scoop to separate them into smaller
units. In a dispenser, this ice will break up into
mostly individual cubes as the dispense
mechanism moves the ice.
The ice in the bin will slope down from the right to
the left. This is normal.
Heat
Air cooled models will generate heat when in
operation. That heat is discharged out the back of
the cabinet.
Noise
The ice machine will make noise when it is in ice
making mode. The compressor, fan motor(s) if air
cooled and water pump all produce some sound. It
is also normal to hear some cracking just before
the harvest cycle begins. In addition, during the
harvest cycle the harvest assist solenoid will click
twice as it pushes the ice out and returns to its
normal position. The ice harvests as a unit or slab,
which makes some noise when it impacts the bin or
dispenser. These noises are all normal for this
machine.
July 2007
Page 14
C0322 through C1030
Air and Water Cooled Installation Manual
SmartBoard Advanced Feature Control™
See Instructions for Available Features
34 SEL
02-4293-01 Rev A.
ENTER
ESC

Cleaning, Sanitation and Maintenance
This ice system requires three types of
maintenance:
•Remove the build up of mineral scale from
the ice machine’s water system and sensors.
•Sanitize the ice machine’s water system and
the ice storage bin or dispenser.
•Clean or replace the air filter and clean the
air cooled condenser (air cooled models
only).
It is the User’s responsibility to keep the ice
machine and ice storage bin in a sanitary condition.
Sanitize the ice storage bin as frequently as local
health codes require, and every time the ice
machine is cleaned and sanitized.
The ice machine’s water system should be
cleaned and sanitized a minimum of twice per
year. This is critical to the proper operation of
the ice machine. Contact you local authorized
service agent for water system cleaning.
.Air cooled condenser filter
1. Pull air filter(s) forward from side panel.
2. Wash the dust and grease off the filter.
3. Return it to its original position.
Do not operate the machine without the filter in
place except during cleaning.
Air cooled condenser
If the machine has been operated without a filter
the air cooled condenser fins will need to be
cleaned.
They are located under the fan blades. The
services of a refrigeration technician will be
required to clean the condenser.
Exterior Panels
The front and side panels are durable stainless
steel. Fingerprints, dust and grease will require
cleaning with a good quality stainless steel cleaner.
Water filters
If the machine has been connected to water filters,
check the cartridges for the date they were
replaced or for the pressure on the gauge. Change
cartridges if they’ve been installed more than 6
months or if the pressure drops too much when the
ice machine fills with water.
July 2007
Page 15
C0322 through C1030
Air and Water Cooled Installation Manual
Air Filter

What to do before calling for service
Reasons the machine might shut itself off:
•Lack of water.
•Freeze cycle takes too long.
•Harvest cycle takes too long.
•High discharge temperature.
•Controller self test failure.
Check the following:
1. Has the water supply to the ice machine or
building been shut off? If yes, the ice machine will
automatically restart within 25 minutes after water
begins to flow to it.
2. Has power been shut off to the ice machine? If
yes, the ice machine will automatically restart when
power is restored.
3. Has someone shut the water off to a water
cooled unit? If yes, after the water supply has been
restored the ice machine may need to be manually
reset.
4. Is the curtain open because some ice is stuck
under it? If so, remove the ice and the machine
should start in a few minutes.
Note: Curtain can be removed & replaced anytime
the machine is in a standby mode or when it is in a
freeze cycle. However, removal of the curtain
during freeze will result in water flowing into the
bin. Removal of the curtain during harvest
terminates harvest at that point and, if left off, will
result in the machine shutting off.
To Manually Reset the machine.
•Push and release the Off button.
•Push and release the On button.
To Shut the Machine Off:
1. Push and hold the Off button for 3 seconds or
until the machine stops.
July 2007
Page 16
C0322 through C1030
Air and Water Cooled Installation Manual
Reset or Switch Off
Clear ice From Beneath Curtain
Clear Ice
From Here
Curtain

Introduzione
Il design di questo fabbricatore modulare di ghiaccio
a cubetti è il risultato di anni di esperienza e collaudi.
Le caratteristiche standard includono spie indicatrici e
interruttori di accensione e spegnimento accessibili dal
lato anteriore, che consento un rapido accesso ai dati
fondamentali e semplificano il controllo operativo.
Conservare il presente manuale come riferimento futuro.
Questo manuale dell’utente e di installazione è suddiviso
in tre sezioni principali: Installazione, che fornisce al
rappresentante di vendita le informazioni necessarie
per posizionare e installare questo prodotto; Uso e
Funzionamento, che fornisce all’utente le informazioni
necessarie per utilizzare il prodotto; e Manutenzione,
che fornisce all’utente le informazioni necessarie per
preservare il corretto funzionamento dell’apparecchio.
Osservare scrupolosamente le informazioni contraddistinte
dai simboli di attenzione o avvertenza riportate sul prodotto
o in questo manuale. Tali informazioni indicano potenziali
pericoli.
Luglio 2006
Pagina 1
C0322 a C1030
Manuale di installazione del refrigeratore aria e acqua
Sommario
Introduzione ................................................... Pagina 1
Installazione: Specifiche tecniche ........................................ Pagina 2
Descrizione del codice modello ......................................... Pagina 3
Acqua ...................................................... Pagina 4
Struttura dell’apparecchio C0322 e C0522 ................................... Pagina 5
Struttura dell’apparecchio C0330, C0530, C0630, C0830 e C1030....................... Pagina 6
Rimozione dei pannelli.............................................. Pagina 7
Requisiti idraulici................................................. Pagina 8
Collegamenti elettrici .............................................. Pagina 9
Accensione iniziale ............................................... Pagina 10
Regolazioni ................................................... Pagina 11
Uso e Funzionamento .............................................. Pagina 12
Interruttori di controllo .............................................. Pagina 13
Componenti opzionali .............................................. Pagina 14
Pulizia, igienizzazione e manutenzione ..................................... Pagina 15
Operazioni da svolgere prima di rivolgersi all’assistenza ............................ Pagina 16

Installazione: Specifiche tecniche
Limitazioni per il posizionamento:
Il prodotto è concepito per essere installato in ambienti interni
e controllati. I modelli raffreddati ad aria scaricano dal lato
posteriore aria estremamente calda nell’ambiente di
installazione. È necessario lasciare un adeguato spazio sui
lati sinistro e posteriore per consentire la circolazione dell’aria.
I modelli raffreddati ad acqua scaricano acqua calda nelle
condotte di scarico dell’edificio. È necessario lasciare un
adeguato spazio sui due lati e superiormente per consentire
l’accesso di servizio.
Limitazioni di spazio
Nota: se la distanza dalle pareti laterali, posteriore e superiore
è minimo, la macchina continuerà a funzionare, tuttavia
la capacità delle macchine raffreddate ad aria risulterà
sensibilmente ridotta. Inoltre, per tutti i modelli, si consiglia
di lasciare uno spazio adeguato per gli interventi di
servizio e manutenzione.
Per un funzionamento adeguato, si consiglia di lasciare 150
mm di spazio dalle pareti laterali e posteriore. Per ottenere
la capacità produttiva massima, posizionare la macchina
distante da apparecchi che generano calore e dai condotti
di riscaldamento, mantenere il lato sinistro lontano dai muri
e osservare una distanza di 300-450 mm per consentire
un buon flusso di aria.
Il flusso di aria è in entrata dal lato sinistro (rispetto a chi
guarda la macchina) e in uscita dal lato posteriore.
Limitazioni ambientali
Minima Massima
Temperatura
dell’aria 10oC.38oC.
Temperatura
dell’acqua 5oC.38oC.
Pressione
dell’acqua 1 bar 5 bar
Alimentazione – intervalli di tensione consentiti
Minima Massima
Modello a 230 volt 207 volts 253 volts
Tabella di riferimento dei cavi di alimentazione
Corrente nominale del
modello
Sezione nominale (mm2)
dei fili
da 3,1 a 6 A ,75
da 6,1 a 10 A 1,0
da 10,1 a 16 A 1,5
da 16,1 a 25 A 2,5
Informazioni sulla garanzia
Il certificato di garanzia per questo prodotto viene fornito
separatamente dal presente manuale. Fare riferimento al
certificato di garanzia per informazioni sulla copertura
applicabile. In generale, la garanzia copre difetti di materiali
o lavorazione. La garanzia non copre la manutenzione, le
correzioni all’installazione o le situazioni in cui la macchina
viene utilizzata in circostanze che eccedono le limitazioni
precedentemente indicate.
Informazioni sul prodotto
Questo apparecchio è un fabbricatore modulare di ghiaccio
a cubetti. Questo tipo di macchina è concepito per essere
posizionato al di sopra di un contenitore o un distributore
di ghiaccio. Per molte installazioni è necessario
esclusivamente il contenitore corrispondente, tuttavia, per
alcune installazioni è necessario un adattatore da installare
tra il fabbricatore di ghiaccio a cubetti e il contenitore o tra
il fabbricatore di ghiaccio a cubetti e il distributore. Questo
apparecchio non può essere installato sovrapposto.
Vedere la tabella riportata di seguito per informazioni
sull’applicazione dei contenitori.
Luglio 2006
Pagina 2
C0322 a C1030
Manuale di installazione del refrigeratore aria e acqua
Flusso dell’aria