Scotsman CU0415 User manual

User Manual for Models CU0415, CU0715 and CU0920
July 2013
Page 12
Maintenance
Regularly vacuum the right side of the air cooled
condenser with a brush to remove all loose dust and
dirt. Be careful not to damage the ns.
Cubed ice machines of this type make ice that is
more pure than the water supplied to it. Since the ice
has fewer impurities, the water that remains in the
reservoir has more. The water system dilutes that
concentration but eventually it does build up and need
to be removed. Over the years it has been determined
that the typical scale removal frequency is about 2
times per year.
To remove scale from the water system.
Materials needed:
Food grade, nickel safe scale remover for ice
machines, also known as ice machine cleaner.
• Sanitizer
• Hand tools.
• Clean bucket
• Clean cloths
• Rubber or plastic gloves
1. Remove front panel.
2. Move master switch to Off, wait a minute and then
move it to On.
3. When the freeze cycle begins (blue light on),
switch the machine to Off.
4. Remove and discard the ice.
5. Drain reservoir by pulling drain plug and return
drain plug to its original position.
6. Mix a solution of 5 oz or 150 cc of Scotsman Clear
1 Scale Remover and 2.5 quarts or 2.4 liters of
clean, warm (95oF/35oC to 115oF./46oC) water.
7. Pour the solution into the reservoir by carefully
adding it at the reservoir’s front lip.
8. Move the master switch to the Wash position.
9. Wait 10 minutes.
10. Move the master switch to the Off position.
11. Drain the reservoir by removing drain plug and
draining the solution into the bin. Return the drain
plug to its normal position.
12. Remove spray platform by removing cube chute
and lifting spray platform up and off its connection.
If needed open platform and conrm all jets are
open. Rinse out any debris, reclose and return it
and the cube chute to the unit. Be sure gasket is
positioned correctly - narrow side faces up toward
jets.
13. Pour 2.5 quarts or 2.4 liters of warm (95oF/35oC to
115oF./46oC) water into the reservoir by adding it
at the reservoirs’ front lip.
14. Switch the master switch to Wash for 1 minute,
then switch it to Off.
15. Repeat step 11. Go to the next process to sanitize
the machine.
Sanitize Water System – after completing prior scale
removal and stopping at the end of its steps.
1. Mix a 1 gallon or 4 liter solution of locally
approved sanitizer and clean, warm (95oF/35oC
to 115oF./46oC) water. Use an EPA approved
food equipment sanitizer at the solution mix
recommended by the sanitizer manufacturer.
2. Pour about half of the sanitizer mix into the
reservoir.
3. Remove the cube chute and spray platforms and
wash them with the sanitizer, then return them to
the ice machine.
4. Move the master switch to the Wash position.
5. Circulate the sanitizer for 2 minutes.
6. Move the master switch to Off.
Ice machine scale remover
contains acids. Acids can
cause burns.
If concentrated cleaner comes
in contact with skin, ush with
water. If swallowed, do NOT
induce vomiting. Give large
amounts of water or milk. Call
Physician immediately. Keep
out of the reach of children.

July 2013
Page 13
User Manual for Models CU0415, CU0715 and CU0920
7. Drain the reservoir into the storage bin by
removing the drain plug. Return the drain plug to
its normal position.
8. Wash all interior surfaces of the ice machine
storage bin, reservoir surface and inside of the
door with the remaining sanitizer solution.
9. Pour any excess sanitizer down the ice machine
bin drain.
10. Pour 2.5 quarts or 2.4 liters of warm (95oF/35oC to
115oF./46oC) water into the reservoir by adding it
at the reservoirs’ front lip.
11. Move the master switch to the Wash position for 1
minute, then switch it to Off.
12. Drain the reservoir by removing the drain plug and
draining the solution into the bin. Return the drain
plug to its normal position.
13. Move switch to the On position. The machine will
resume normal ice making.
14. Return the front panel to its original position and
secure it with the original screws.
Cleaning the Condenser
1. Remove the front panel.
2. Switch the machine to OFF.
3. Vacuum the surface of the condenser ns,
carefully brush off any loose dirt. If grease is
imbedded use coil cleaner to wash it out.
4. Switch the machine to ICE.
5. Return the front panel to its original position.