Screen Innovations Nano Box WireFree RTS User manual

INSTALLERS: Please leave this manual with the owner.
WireFree RTS
Nano Box
Installation Instructions
Doc. # 400023

Shades
Shade Charger
Leveling Shims
(4 per shade)
Installation Remotes
(1 per RTS shade)
Wall Brackets (2)
Screws Included
(3 per Bracket)
Longer Screws Included
275 Box
375 Box
Spacer Blocks
(optional - 4 per shade)
mymy
PARTS LIST - NANO BOX - WIREFREE
Parts list - Nano Box - Wirefree 1
OR
Please note all the Serial No.s on your Shade motors.
See the last page on these instructions.

Spacer blocks and Leveling Shims 2
Spacer Blocks - used to clear an obstruction in the fabric path.
Leveling Shims - used if the window frame is out of level.
Connect to shade brackets before installation
Note: Do not use more than 2 leveling shims per bracket.
Note: Do not use more than 4 spacer blocks per bracket.
Connect spacer blocks to shade brackets before installation.
SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL)

2. Make sure the wall bracket lever is down (may already be down).
INSTALLATION - NANO BOX - WIREFREE
3. Hang shade onto wall brackets and center in opening
Installation - Nano Box - Wirefree 3
Proper position for
installing Box
1. Install the wall brackets 4 - 6 inches in from the end of the shade with the supplied screws.
(The closer to the end of the cassette, the better.)
4” - 6” 4” - 6”

INSTALLATION - NANO BOX - WIREFREE
4. Use thumb to lock shade in place
Installation - Nano Box - Wirefree 4

Programming - RTS 5
PROGRAMMING - RTS
Each RTS Nano shade includes an installation remote that is used to adjust limits and program
group controls. These installation remotes are uniquely numbered to the shade they are paired
with. The lower limit of every shade is preprogrammed to ½” from the bottom of the window.
After installing each shade, follow these steps to adjust the lower limit:
STEP 2 - Assign shades to groups :
Next, program group controls. To pair with a permanent transmitter
such as a multichannel Telis or DecoFlex, follow these steps.
1. Press and hold the program button on the back of the installation
remote until the shade jogs.
2. Select the channel where you want to create a group, then bump
(do not hold down) the program button on the back of the remote -
the shade will jog.
3. Both remotes now control the shade.
4. Continue doing this with each shade until all shades are
programmed in the desired groups.
NOTE: Each RTS motor can be paired with 12 unique transmitters.
PROGRAMMING STEPS (must follow in order)
Step 1: Fine tune lower limit
Step 2: Assign shades to groups
Step 3: Pair groups to control system (Mylink, LinkPro)
1. Beginning with the rst shade, pull plastic tab from remote and press allowing shade to run
to lower limit set at the factory.
2. When shade has stopped, adjust the lower limit by holding and simultaneously until the
shade jogs.
3. Use or to move the shade to the desired lower limit.
4. Hold the “My” button until the shade jogs again.
5. Repeat this procedure at each window until all shades have lower limits set to desired positions.
1. Download the myLink app.
2. Pair the grouped shades with LinkPro or MyLink according to the instructions in the myLink app.
STEP 1 - Fine tuning lower limit :
STEP 3 - Pair Groups to control system (LinkPro, myLink) :
Warning: Do not
attempt to use any
installation remote until all
the shades are installed.
hold the button
until the shade jogs
(light on the motor
turns green).
Installation
Remote
Permanent
Remote
Bump
(do not hold)

TROUBLESHOOTING - RTS
For RTS
Problem Possible Cause Action to Take
Shade won’t operate. Motor is not powered.
When the battery of a wire free motor is low the user
is notied by a series of red led flashes visible on
the left end cap. These flashes will only occur after a
command has been given. If the motor is low or dead,
the charging cord can be plugged in and the shade
will operate while charging.
Remote button presses
are too short.
When operating an RTS remote hold the buttons
down for at least 2 seconds.
The remote is being
used out of range.
Move within 30ft. of the shade. If the issue persists,
adjust the antenna to a new position, and make sure
the antenna does not touch metal.
The remote battery is
out of place or drained.
Check that the red LED on the remote flashes when
buttons are pressed. On the installation remote, pry
off the back by hand and ensure the battery is fully
seated in the battery tray. If the remote remains
unresponsive, replace the battery with a CR2430 3V
lithium cell.
Green LED light is
flashing - shade is not
operating properly
(WireFree only).
The motor is in
programming mode.
Briefly click the program button on the back of the
installation remote. The green light will turn off and
the shade will return to user mode.
Move the shade to the lower limit by holding the up
or down button. Hold the “My” button untill the screen
jogs - the green LED will stop flashing.
Troubleshooting - RTS 6
OR
Tech Support: 512.832.6939
Technical Support: 512.832.6939 screeninnovations.com
Hours of Support: 7:30am - 5pm CST [email protected]
Please use this QR Code
to access the updated
installation instructions
and related documents.

NOTES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
7
Notes

MOTOR SERIAL NO.S
Motor Serial No.s
Please keep a note of all the Serial No.s on your shade motors. OR for larger shade orders,
refer to your Sales Order document for the list.
Room
Room
Shade 1
Shade 1
Shade 3
Shade 3
Shade 5
Shade 2
Shade 2
Shade 4
Shade 4
Shade 6

Screen Innovations
9715-B Burnet Rd, Suite 400 Austin, TX 78758
512.832.6939
www.screeninnovations.com
400023 v. 1.3 13 November 2019