Screen Innovations Nano Roll 275 Series User manual

INSTALLERS: Please leave this manual with the owner.
24v DC - RTS
Nano Roll
Installation Instructions
Doc. # 400029

Shades
Wall Brackets (275) + End Caps
Wall Brackets (375 / 475) + End Caps
Screws included (3 per bracket)
PARTS LIST  NANO ROLL  24v DC  RTS
Parts list - Nano Roll - 24v DC - RTS 1
275 Roll
375 Roll
475 Roll
Terminal Blocks
Motor Side
Motor Side
Idler Side
Idler Side
Please note all the Serial No.s on your Shade motors.
See the last page on these instructions.

PARTS LIST  NANO ROLL  24v DC  RTS
Parts list - Nano Roll - 24v DC - RTS 2
Spacer Blocks (optional)
Leveling Shims (optional)

ADDITIONAL ACCESSORIES
Additional Accessories list - Nano Roll - 24v DC - RTS 3
Set Screw Hex Tool (1/16”)5/16” Magnetic Driver
Note: For more information about these tools and their use, please call Tech Support at
512.832.6939 Opt. 1
1/4” Magnetic Driver
Included with 375 / 475 series only
Included with 275 series only

Spacer Blocks and Leveling Shims (Optional) 4
SPACER BLOCKS AND LEVELING SHIMS (OPTIONAL)
Spacer Blocks - used to clear an obstruction in the fabric path.
Leveling Shims - used if the window frame is out of level.
Note: Do not use more than 4 spacer blocks per bracket.
Connect to shade brackets before installation
Note: Do not use more than 2 leveling shims per bracket.
Connect spacer blocks to shade brackets before installation.

1. Terminate pre-wire with terminal block
2. Install wall bracket/end cap assembly with the supplied screws
5
INSTALLATION  24v DC  RTS 275 SERIES
Header
Jamb
+ 24 VDC
- 24 VDC
V+
V-
+
-
G
Installation - Nano Roll - 24v DC - RTS (275)
Before installing the shades, verify whether the shade was ordered as standard roll or reverse roll. Though
illustrations in this manual show standard roll shades, the installation for reverse roll shades is the same.
Not
Used
Use 1/4” magnetic
driver (incl.)
for Ceiling Mount
Motor side Idler side
for Wall
Mount

INSTALLATION  24v DC  RTS 275 SERIES
4. Remove idler end cap with flat screw driver
3. Measure bracket to bracket width and verify it matches the ordered width. Adjust accordingly.
6
Installation - Nano Roll - 24v DC - RTS (275)
Brackets must be level before the
shade is installed!

5. Connect shade and pre-wire connectors, snap into bracket
6. Insert motor side completely. Then, while supporting motor side, put idler end cap over the idler
and snap into place.
7
INSTALLATION  24v DC  RTS 275 SERIES
Installation - Nano Roll - 24v DC - RTS (275)
When installing, the shade should be at the
upper limit.

INSTALLATION  24v DC  RTS 275 SERIES
8
Installation - Nano Roll - 24v DC - RTS (275)
There will be an audible click.

1. Terminate pre-wire with terminal block
2. If mounting to a wall, remove the ceiling flange from motor and idler brackets
9
INSTALLATION  24v DC  RTS 375  475 SERIES
Installation - Nano Roll - 24v DC - RTS (375 / 475)
Header
Jamb
+ 24 VDC
- 24 VDC
V+
V-
+
-
G
Not
Used

3. Measure bracket to bracket width and verify it matches the ordered width. Adjust accordingly.
Brackets must be level before the
shade is installed!
INSTALLATION  24v DC  RTS 375  475 SERIES
2. Install wall bracket/end cap assembly with the supplied screws
for Ceiling Mount
Motor
side Idler
side
for Wall
Mount
Use 5/16” magnetic
driver (incl.)
10
Installation - Nano Roll - 24v DC - RTS (375 / 475)

INSTALLATION  24v DC  RTS 375  475 SERIES
4. Remove both end caps
Motor End cap
1/16” hex tool
Idler End cap
11
Installation - Nano Roll - 24v DC - RTS (375 / 475)

6. Align and insert the motor side.
5. Connect shade and pre-wire, snap connector into spring clip.
12
INSTALLATION  24v DC  RTS 375  475 SERIES
Installation - Nano Roll - 24v DC - RTS (375 / 475)

INSTALLATION  24v DC  RTS 375  475 SERIES
13
Installation - Nano Roll - 24v DC - RTS (375 / 475)
7. Make sure the motor head bracket is fully seated. Secure with cotter pin.

INSTALLATION  24v DC RTS 375  475 SERIES
Installation - Nano Roll - 24v DC - RTS (375 / 475) 14
8. Put idler end cap over idler and snap into place.
There will be an audible click.

INSTALLATION  24v DC  RTS 375  475 SERIES
9. Replace and fasten motor end cap
15
Installation - Nano Roll - 24v DC - RTS (375 / 475)
1/16” Hex tool

Programming - RTS 16
PROGRAMMING  RTS
Each RTS Nano shade includes an installation remote that is used to adjust limits and program
group controls. These installation remotes are uniquely numbered to the shade they are paired
with. The lower limit of every shade is preprogrammed to ½” from the bottom of the window.
After installing each shade, follow these steps to adjust the lower limit:
STEP 2 - Assign shades to groups :
Next, program group controls. To pair with a permanent transmitter
such as a multichannel Telis or DecoFlex, follow these steps.
1. Press and hold the program button on the back of the installation
remote until the shade jogs.
2. Select the channel where you want to create a group, then bump
(do not hold down) the program button on the back of the remote -
the shade will jog.
3. Both remotes now control the shade.
4. Continue doing this with each shade until all shades are
programmed in the desired groups.
NOTE: Each RTS motor can be paired with 12 unique transmitters.
PROGRAMMING STEPS (must follow in order)
Step 1: Fine tune lower limit
Step 2: Assign shades to groups
Step 3: Pair groups to control system (Mylink, LinkPro)
1. Beginning with the rst shade, pull plastic tab from remote and press allowing shade to run
to lower limit set at the factory.
2. When shade has stopped, adjust the lower limit by holding and simultaneously until the
shade jogs.
3. Use or to move the shade to the desired lower limit.
4. Hold the “My” button until the shade jogs again.
5. Repeat this procedure at each window until all shades have lower limits set to desired positions.
1. Download the MyLink app.
2. Pair the grouped shades with LinkPro or MyLink according to the instructions in the MyLink app.
STEP 1 - Fine tuning lower limit :
STEP 3 - Pair Groups to control system (LinkPro, MyLink) :
Warning: Do not
attempt to use any
installation remote until all
the shades are installed.
hold the button
until the shade jogs
(light on the motor
turns green).
Installation
Remote
Permanent
Remote
Bump
(do not hold)

Tech Support: 512.832.6939
TROUBLESHOOTINGTROUBLESHOOTING  RTS
Troubleshooting - RTS 17
Problem Possible Cause Action to Take
Shade won’t operate. Motor is not powered.
When the battery of a wire free motor is low the user
is notied by a series of red led flashes visible on
the left end cap. These flashes will only occur after
a command has been given. If the motor is low or
dead, the charging cord can be plugged in and the
shade will operate while charging.
Remote button presses
are too short.
When operating an RTS remote hold the buttons
down for at least 2 seconds.
The remote is being
used out of range.
Move within 30ft. of the shade. If the issue persists,
adjust the antenna to a new position, and make sure
the antenna does not touch metal.
The remote battery is
out of place or drained.
Check that the red LED on the remote flashes when
buttons are pressed. On the installation remote, pry
off the back by hand and ensure the battery is fully
seated in the battery tray. If the remote remains
unresponsive, replace the battery with a CR2430 3V
lithium cell.
Green LED light is
flashing - shade is not
operating properly
(WireFree only).
The motor is in
programming mode.
Briefly click the program button on the back of the
installation remote. The green light will turn off and
the shade will return to user mode.
Move the shade to the lower limit by holding the up
or down button. Hold the “My” button untill the screen
jogs - the green LED will stop flashing.
For RTS
OR
Technical Support: 512.832.6939 screeninnovations.com
Hours of Support: 7:30am - 5pm CST [email protected]
Please use this QR Code
to access the updated
installation instructions
and related documents.

MOTOR SERIAL NO.S
Motor Serial No.s
Please keep a note of all the Serial No.s on your shade motors. OR for larger shade orders,
refer to your Sales Order document for the list.
Room
Room
Shade 1
Shade 1
Shade 3
Shade 3
Shade 5
Shade 2
Shade 2
Shade 4
Shade 4
Shade 6

Screen Innovations
9715-B Burnet Rd, Suite 400 Austin, TX 78758
512.832.6939
www.screeninnovations.com
®
400029 v. 1.2 15 October 2019