Sea-doo SEASCOOTER PRO User manual

English Version
CAUTION
ELECTRICALLY OPERATED PRODUCT
Not recommended for children under 16 years of age. As with all
electrical products, precautions should be observed during handling
to reduce the risk of electric shock.
User Manual
SDP15870
Distributors in the United States and Canada provide a standard Limited
Warranty for 6 months from the date of purchase for new products. If
you're not located in the United States or Canada, please contact your
Local Distributor for warranty arrangements in your territory. Please
visit www.seadooseascooter.com for Distributor / Service Center details.
Distributors ONLY warrant Stallion products purchased from an
authorized dealer.
Ask your Local Distributor for the warranty period in your region by calling their
Service Center. Any part of the product supplied by the Distributor and found in the
reasonable judgment of the Distributor to be defective in material or workmanship
will be repaired or replaced by the Distributor without charge for parts or labor. The
product including any defective part must be sent to the Distributor within the
warranty period. The customer will pay for the expense of delivering the product to
the Distributor. The Distributor will pay for the expense of returning the product to
the customer.
ALWAYS ACTIVATE YOUR WARRANTY IMMEDIATELY ON
http://www.seadooseascooter.com/warranty.html
www.seadooseascooter.com
WARRANTY & CUSTOMER SERVICE
INFORMATION
Distributors ONLY warrant products with an active
Warranty Registration
SEE NEXT PAGE
Model no. SD5540
SEA-DOO®SEASCOOTER™ GTI
Model no. SD6545 X
SEA-DOO®SEASCOOTER™ VS SUPERCHARGED X
Model no. SD25001
SEA-DOO®SEASCOOTER™ GTS
Model no. SD75001
SEA-DOO®SEASCOOTER™ PRO
GTI
VS SUPERCHARGED PLUS
PRO
GTS

Contents Introduction
Introduction 1
Parts diagram 2
Warnings 4
Getting started 6
Battery use 11
Charging the battery 15
Care & maintenance 21
Trouble shooting 23
Technical specifications 28
Thank you for having chosen the SEA-DOO®SEASCOOTER™
PRO / GTI / VS SUPERCHARGED PLUS / GTS - with the
SEASCOOTER™swimming, snorkeling and diving is effortless
and fun.(Only use the seascooter for scuba diving if you are
a qualified diver)
Use appropriate equipment such as wetsuit, buoyancy
control device, fins, mask & snorkel, surface signaling
device, regulator(s) approved life jacket etc. when
operating the seascooter.
Only operate the Seascooter in water.
- SEASCOOTER™ PRO -
• Speed up to 2.0 mph / 3.2 km/h
• Run up to 1 hour with normal use
• Rated to 65 ft / 20 m
• Weight just 13 lb / 6 kg including battery
- SEASCOOTER™ GTI -
• Speed up to 2.5 mph / 4 km/h
• Run up to 2 hours with normal use
• Rated to100 ft / 30 m
• Weight just 18 lb / 8.2 kg including battery
- SEASCOOTER™ VS SUPERCHARGED PLUS -
• Speed up to 3 mph / 4.8 km/h
- SEASCOOTER™ GTS -
• Speed up to 2.8 mph / 4.5 km/h
• Run up to 1.5 hours with normal use
• Rated to100 ft / 30 m
• Weight just 18 lb / 8.2 kg including battery
There are many features incorporated in this sophisticated
design, please take time to study the manual to learn about
them all to get the most out of your SEASCOOTER™.
1
Discarded electrical appliances are
recyclable and should not be discarded
in the domestic waste! Please actively
support us in conserving resources and
protecting the environment by returning
this appliance to the collection centers
(if available).
• The seascooter is designed for 1 person use
• The seascooter is not a life saving device. Do not use it as
a buoyancy aid
WARNING
The Seascooter is designed for use in seawater. It will
have less buoyancy in fresh water, lake or pool and
may sink in such waters.

Parts Diagram
-SEASCOOTER GTI / VS SUPERCHARGED PLUS / GTS-
1
2a
2b
3
11 10
12
13
14
15
7
6
8
9
5
4
16 17 18
Fig.2
3
Parts Diagram
-SEASCOOTER PRO-
2
1
23
11 10
12
13
14
7
6
8
9
5
4
15 16 17
Fig.1
1 Latch
2a Nose Cone (GTI and
VS SUPERCHARGED PLUS)
2b Nose Cone (GTS)
3 Inner Nose Cone
4 Vent Plug
5 Trigger
6 Handle
7 Nozzle
8 Propeller
9 Protective Grilles
10 Battery Housing
11 Master Switch
1 Latch
2 Nose Cone
3 Inner Nose Cone
4 Vent Plug
5 Trigger
6 Handle
7 Nozzle
8 Propeller
9 Protective Grilles
10 Battery Housing
11 Master Switch
12 Battery
13 Vent Hole
14 Buoyancy Control
Chamber
15 Silicone Ring
16 Pump
17 Lubricant
18 Charger
19 Charger Jack
21
(For VS Supercharged Plus only)
12 Battery Leads
13 Battery
14 Vent Hole
15 Buoyancy Control
Chamber
16 Silicone Ring
17 Pump
18 Lubricant
19 Charger
20 Charger Jack
21 Nose Cone Protector
18
19
19
20

• Never remove the grilles except for maintenance.
•
Always charge battery to its maximum before using the
SEASCOOTER™. After charging is complete the battery
will continue to emit gas. Wait at least 30 minutes after
charging before removing the battery from the charger or
placing the battery into the battery housing. Failure to do
so could result in an explosion.
•
Ensure sufficient battery charge remains for return to
shore or surface.
• The Seascooter™ is not a personal floatation device -
always wear a Approved Personal Flotation Device /
Approved Life-Preserver when using the Seascooter™ for
snorkeling.
•
Be aware of appropriate water levels, tidal changes,
dangerous currents, weather changes and strong offshore
winds. Always scout unfamiliar water.
54
Warnings
14 +
14 +
16 +
•Read the user's manual carefully before use.
•Always follow this age recommendation: a
child under 16 years old should never operate
this SEA-DOO®SEASCOOTER™.
•Crushing / Cutting Hazard
•Be careful when you are transporting the
Seascooter and setting it down to avoid
crushing hazard on hands, foot or toes.
•This is not a life saving device.
•Never stick body parts, clothing or other
objects in the vicinity of the Propeller. Do not
wear loose or flowing clothing or equipment
that could be drawn into the propeller.
•Particular care should be exercised when
using the SEASCOOTER™ near anybody
with long hair. Users with long hair should tie
it up or wear a swimming cap when using the
SEASCOOTER™.
•Always inspect the swimming area to ensure
it is free of hazards or obstacles such as
boats and swimmers before using the
SEASCOOTER™.
• ALWAYS wear a life vest (personal floatation
device - PFD) approved by your local
authorities for Snorkeling: (U.S. Coast Guard
Type III vest in the US or Canadian Coast
Guard approved life vest in Canada or SAI
Approval PFD in Australia or CE / ISO
Approved PFD in Europe).

Getting Started
• Do not use alcohol or drugs prior to using this product.
• ALWAYS keep the SEA-DOO®SEASCOOTER™out of
direct sunlight when not in use. HEAT KILLS BATTERIES
AND IT MAY EXPLODE OR LEAK.
• When using the SEA-DOO®SEASCOOTER™for
SCUBA-DIVING, ascents and descents should be made in
accordance with recognized diving practices.
• The SEA-DOO®SEASCOOTER™should only be used for
SCUBA-DIVING by qualified divers.
• Never open the Cover of the SEA-DOO®SEASCOOTER™
in the water.
• When not in use, always turn the Master Switch to the off
position.
•
Do not use the SEASCOOTER™PRO below the
recommended maximum depth of 20m/65ft.
•
Do not use the SEASCOOTER™GTI / VS SUPERCHARGED
PLUS / GTS
below the recommended maximum depth of
30m/100ft.
• ALWAYS remove the battery from the unit when not in use.
• DO NOT store the battery in the unit
CAUTION:
• In different waters (seawater, lake, pool) and conditions
such as currents, temperature and pressure can affect the
buoyancy of the unit which may cause the unit to sink if
accidentally released.
• DO NOT release or leave the Seascooter in the water.
Always take the unit out of water when not in use.
When you buy the
SEA-DOO®SEASCOOTER™ the battery
is disconnected and needs to be charged. Follow the
Battery Instruction on pages 12 to 15 and charging
instructions on pages 16 to 19.
Using the SEASCOOTER™for swimming and snorkeling.
When swimming or snorkeling the SEA-DOO®
SEASCOOTER™
should be kept positively buoyant - this is
done by simply making sure the Buoyancy Chamber is
empty and fitted inside the Nose Cone.
To use the SEASCOOTER™for swimming or snorkeling
follow these instructions.
1.Charge the battery and install just before use.
2.Make sure that Vent Plug is closed.
3.Replace the Buoyancy Control Chamber.
4.Place the SEA-DOO®SEASCOOTER™ into the water so
the Handle, Outer Nose Cone and Nozzle fill with water.
CRUSHING HAZARD:
The following action during assembly, disassembly, and
transportation of the seascooter may incur crushing hazards
to your fingers or toes:
-Closing the nose cone latches
-Putting on the nose cone housing
-Placing the battery into the seascooter
-Accidental dropping of the seascooter or battery.
6 7

5.When ready to set off, turn the Master Switch to the
On position shown in figure 3.
6. Pull and hold both Triggers to start the Propeller.
(There is a short delay before the Propeller begins
to rotate).
7. To stop the Propeller, simply release the Triggers.
8.Always turn the Master Switch off when out of the water.
9.
Proper posture when using the SEA-DOO®
SEASCOOTER™ is important to achieve the maximum
speed - see figure 4 for the correct position of the
SEA-DOO®SEASCOOTER™when using it.
Fig.3
SEASCOOTER GTI / VS SUPERCHARGED PLUS
Shown in "ON" position
Rotate to turn "OFF"
CAUTION
Do not dive deeper than you would normally when snorkeling,
to ensure you can get back to the surface safely.
Important Notice: This machine is not to use to mix
or to work with sand, concrete and material with
similar physical characteristics. This machine is
only to use for diving in water.
98
SEASCOOTER PRO
Shown in "ON"
position Rotate to turn
"OFF"
Fig.4
PRO
GTI
VS SUPERCHARGED PLUS
GTS

Using the SEA-DOO®SEASCOOTER™
for diving - adjusting the buoyancy.
Your SEASCOOTER™ PRO can be used for diving up to
20m/65ft but will need to be adjusted for neutral buoyancy.
Your SEASCOOTER™ GTI / VS SUPERCHARGED PLUS /
GTS can be used for diving up to 30m/100ft but will need to be
adjusted for neutral buoyancy.
The SEASCOOTER™must never be adjusted for negative
buoyancy to avoid it sinking if accidentally released.
To adjust for neutral buoyancy follow these instructions
1.
Make sure the SEA-DOO®SEASCOOTER™ is in the Off
position.
2. Remove the SEASCOOTER™from the water, give a half
turn to the Latches, remove them (see figure 5) and
remove the Buoyancy Control Chamber.
3. Open the Buoyancy Chamber and add a small amount of
rocks or a lead weight (see figure 6).
4.
Cover the Buoyancy Chamber with the Nose Cone then
secure the latches and place the SEASCOOTER™ in the
water. If the SEASCOOTER™ is neutrally buoyant it will
neither float nor sink.
5. If the SEASCOOTER™ sinks, remove the weight until it is
neutrally buoyant.
If the SEASCOOTER™ is still positively buoyant repeat
step 3, until it is neutrally buoyant.
Rotate 180oand remove to open
Fig.5
1110
Fig.6
CAUTION
If the SEASCOOTER™is later used for swimming or
snorkeling be sure to remove the weight from the
Buoyancy Chamber so the SEA-DOO®SEASCOOTER™
has positive buoyancy.
PRO
GTI
VS SUPERCHARGED PLUS GTS

Battery UseBattery Use
1312
RE-CHARGE THE BATTERY
3
3
AT LEAST
MONTHS
EVERY
MONTHS
WARNING
BATTERY SAFETY
• Must remove and store the
battery separately from the unit
when not in use!
• Must re-charge the battery after
use WITHIN 24 HOURS.
• Must re-charge the battery at
least EVERY THREE MONTHS
when not in use.
User Manual must be read and
understood before use.
Please read and follow the
Battery Safety Instruction.
Incorrect battery maintenance
may reduce the battery life and
influence its function.
www.seadooseascooter.com
CAUTION
• Your SEA-DOO®SEASCOOTER™is supplied with a
battery that needs to be treated carefully as it will
release potentially explosive gases during its normal
cycle of use (off-gassing). Failure to do so can result
in an explosion occurring. Please read the entire
manual thoroughly and follow all instructions.
• Always remove the battery from your SEA-DOO®
SEASCOOTER™when it is not in use. Store
separately in a well ventilated area where it is out of
the reach of children and away from heat and ignition
sources.
• Do not attach the battery in your SEA-DOO®
SEASCOOTER™ until prior to using it.
• Before disconnecting/connecting any cables, open the
nose cone and allow two minutes for any explosive
gases to dissipate.
• Do not use/store/charge the battery in temperatures
above 40ºC (104ºF) as excessive off-gassing may
occur. Keep the battery and SEA-DOO®
SEASCOOTER™in the shade when not in use.
• Always ensure the unit is dried thoroughly before
opening the Nose Cone.
• Only use the charger supplied with the SEA-DOO®
SEASCOOTER™.

Battery UseBattery Use
1514
CAUTION
• The battery supplied with your SEA-DOO®
SEASCOOTER™releases a potentially explosive gas
during charging. Charging should only take place in a
well ventilated area, away from children and open
flames or other ignition sources (cigarettes, sparks).
Never charge the battery while still in the SEA-DOO®
SEASCOOTER™.
• Charge the battery as soon as possible after use within
24 hours.
• Always charge the battery to the fullest before using
the SEA-DOO®SEASCOOTER™.
• Always remove the battery from the battery housing
before charging.
• Always connect charger jack to the battery first and
then plug charger into the electrical socket/plug.
• After charging, disconnect from the electrical
socket/plug first and then disconnect the battery from
the charger.
• After charging is complete the battery will continue to
emit gas. Wait at least 30 minutes after charging before
removing the battery from the charger or placing the
battery into the battery housing. Failure to do so could
result in an explosion.
•
Remove battery from charger once fully charged.
CAUTION
• Never charge the battery in sealed container.
• Never charge the battery near water.
• Never short circuit the battery or battery connectors.
• Always ensure the charger is dry before use.
• The charger gets quite warm in use - this is normal.
• If in doubt of the state of the battery, recharge it until
the indicator on the battery charger indicates a full charge.
• If the battery is not to be used for an extended period,
store it in a well ventilated area away from children,
heat, and ignition sources. Recharge it every three
months to maintain charge and avoid excess
off-gassing. DO NOT store the battery inside the
SEA-DOO®SEASCOOTER™.
• If the battery appears damaged or will not fully charge,
the battery must be replaced. If battery life is noticeably
reduced, the battery should be replaced.
• The battery supplied with your SEA-DOO®
SEASCOOTER™ should last about 200 cycles or two
years before it should be replaced. Please contact your
local customer service center/distributors. Using a
battery in excess of these recommendations can result
in excessive off-gassing of explosive gases.

Charging the battery
For battery charging follow these instructions.
1. Always ensure that the Master Switch is Off -
see figure 3.
2. Always ensure that the SEA-DOO®SEASCOOTER™
is out of the water, dry and placed in a dry area.
3. Give a half turn to the Latches and remove them from
the Nose Cone as shown in figure 5.
4. Remove the Outer Nose Cone and Buoyancy Control
Chamber.
5. Open the Vent by unscrewing the Vent Plug.
6. Remove the Inner Nose Cone. To do this, first feed the
silicone ring (provided with this manual) through the
latch holes in the Inner Nose Cone and pull over the
hooks on the Battery Housing (see figure 7). Then
screw the Pump Nozzle onto the Vent Hole and pump
air into the Battery Chamber until the Inner Nose Cone
pops off and then remove the silicone ring.
7. Allow two minutes for any gases to dissipate.
8. Disconnect the battery cable from the housing cable (if
not already disconnected - the cable will be
disconnected when you buy your SEASCOOTER™) by
pressing the locking feature, as shown in figure 8.
9. Remove the battery and place on a level surface.
10.Connect the battery cable to the charger cable.
11. Plug charger into mains, and turn on the supply.
12.SEASCOOTER PRO - Charging will take 4 to 6 hours
for a fully discharged battery.
SEASCOOTER GTI / VS SUPERCHARGED PLUS /
GTS - Charging will take 6 to 8 hours for a fully
discharged battery.
When the battery is charging the red LED is lit, when
the battery is charged the green LED is lit.
13.Disconnect the charger from the electrical plug/socket.
14.Allow battery to stand for 30 minutes before using it.
Important Notice: Keep the silicone ring permanently (Refer
to Page 2 and 3, Parts Diagram).Removing the inner nose
cone without the silicone ring is dangerous
1716
Fig.7
Press here to release and pull to disconnect
Fig.8
Warning!
Replace the battery immediately if it is damaged.

15.Unplug the battery cable from the Charger cable.
16.When ready for use, install the battery and reconnect to
the housing cable.
20.Screw in the Vent Plug to seal the vent.
21.Replace the Buoyancy Control Chamber.
22.Replace the Outer Nose Cone making sure the key is
aligned correctly and insert the Latches and lock the
Nose Cone by giving them a half turn. See fig.12.
17.
Make sure the seals and sealing surfaces are clean and fully
lubricated with the supplied grease EVERYTIME
(you can
also buy this at your local hardware store)
before
replacing the Inner Nose Cone. See fig. 9.
18.Replace the Inner Nose Cone making sure the key is
aligned correctly. See fig. 10.
19.Ensure the Vent O Ring is fitted correctly and fully
lubricated with the supplied grease
EVERYTIME (you
can also buy this at your local hardware store).
See fig. 11.
1918
Fig.10
O-Ring correctly fitted into
groove and lubricated
Fig.11
Rotate 180oto close
Fig.12
Close up view
PRO
GTI
VS SUPERCHARGED PLUS GTS
Fig.9
Ensure sealing surface is clean and fully lubricated
Ensure the seals are clean and fully lubricated
GTS
Seals Seals
Close up view
of seals
PRO
GTI
VS SUPERCHARGED PLUS
Silicone
Grease
Silicone Grease

To replace a flat battery with a fully charged battery.
1. Follow the steps 1 to 7 on page 16, to open the
SEASCOOTER™.
2. Unplug the battery at the socket by pressing the locking
feature shown in figure 8.
3. Remove the flat battery.
4. Install and connect the charged battery in the correct
position - the leads of the battery must be oriented,
see figure 13.
5. Follow steps 17 to 22 on page 18 and 19, to close the
SEASCOOTER™.
20 21
Standard battery
Standard battery
PRO
Fig.13
GTI
VS SUPERCHARGED PLUS
GTS
-SEASCOOTER PRO-
Using the Optional Extended Life Battery.
An optional extended life battery is available through your
your local customer service center/distributor. This battery
fits into the Battery Housing in a slightly different position
to the normal battery, the leads of the battery must be
oriented, see figure 14.
The extended battery can be charged in the same way as
a standard battery.
Buying batteries
Additional standard or extended batteries can be
purchased separately. Contact your local customer service
center/distributor to purchase them.
CAUTION
Because this battery is heavier than a standard battery
the Buoyancy Chamber must be added and empty to
ensure the SEASCOOTER™floats.
Extended life battery
Fig.14
SEASCOOTER PRO

Care And Maintenance
Battery Care
• Please read and understand important Battery Use
safety information on pages 12 to 15.
• The battery supplied with your SEASCOOTER
™
should
last about 200 cycles or two years before it should be
replaced. Please contact your local customer service
centre/distributor. Using a battery in excess of these
recommendations can result in excessive off-gassing of
hazardous gases.
• ALWAYS remove the battery from the SEASCOOTER
™
immediately after use.
• DO NOT STORE BATTERY IN SEASCOOTER
™
Care after using the SEASCOOTER™
• DO NOT leave the Seascooter in the water. Always take
the unit out of water when not in use.
• Always rinse the SEASCOOTER™in fresh water and
allow it to dry before storage immediately after use.
• To clean the SEASCOOTER™do not use detergents,
only use a damp cloth to wipe the unit clean.
• The Battery Housing interior should be kept dry at
all times.
• If the Battery Housing interior ever gets wet,
see page 28, Accidental Flooding for procedure.
• When storing the SEASCOOTER™for extended periods
of time, open the Vent Plug in the Inner Nose Cone.
• ALWAYS store your SEASCOOTER™vertically when not
in use to prevent deformation of the Propeller Nozzle.
22 23

Trouble Shooting
1. Remove the SEASCOOTER™from the water.
2. Make sure the master switch is off.
3. Remove the battery - see page 16, step 1-9.
Removing rear grille and Propeller to remove obstruction
Unit does not function
If the motor does not start when both triggers are pressed,
make sure
1. The battery is properly connected
2. The battery is fully charged
(see page 16, charging the battery)
3. The master switch is in the "On" position
(see fig 3, page 8)
4. There is no water in the battery compartment
(see page 27, accidental flooding)
Blocked Propeller
If the Propeller becomes blocked first try and remove the
obstruction by removing the front grille. If this is not
possible the back grille and Propeller can be removed.
Under normal use the grilles must not be removed.
Removing the front grille to remove an obstruction.
1. Remove the SEASCOOTER™from the water.
2. Make sure the master switch is in the Off position.
3. Insert a screw driver as shown in figure 15 (page 25) to
remove the two grille pins.
4. Unclip grille as shown in figure 16 (page 25) .
5. Remove obstruction.
6. Reassemble grille and insert clips.
2524
Fig.16
Fig.15
Warning!
Crushing / Cutting Hazard
Before opening the grille for maintenance purpose, make
sure the master switch is in off position, and the battery is
disconnected.
12

9. Replace the washer(s) and nut and tighten with the
socket whileholding the Propeller making sure it is
securely fastened (See figure 20).
10. Replace the grille.
11. Replace the battery.
Sand or Grit on Seals
Ensure that sand/grit does not get on the seals as correct
maintenance and care is essential. To remove sand or grit
from the seals, rinse the seals in fresh water and apply
fresh lubricant. If there is sand inside the Battery Housing,
gently brush the sand from the unit taking care not to
scratch the sealing surfaces.
6. Slide the Propeller off the shaft, taking care not to loose
the drive pin or washers.
7. Remove the blockage from the Propeller.
8. Replace the drive pin (if removed), see figure 19, and
Propeller. Turn the Propeller slowly until you locate the
pin and push the Propeller fully on.
2726
Fig.17
Fig.18
Drive Pin In Position
Fig.19
Nut
Washers
Drive pin
Propeller hub
Fig.20
4. Unscrew the six rear grille screws as shown in figure 17.
5. Whileholding the Propeller, use an M6 socket to remove
the nut from the Propeller shaft (See figure 18).

Technical Specifications
SEASCOOTER™ cuts out
To protect the electronic circuit of your SEASCOOTER™
from damage a safety mechanism has been built in that
cuts the power if a wall or rock or other immovable object
is hit. If this occurs simply wait for a short period to allow
the SEASCOOTER™to reset itself and resume use.
Accidental Flooding
It is important that the seal is kept sand and grit free to
ensure they keep water out and to close the vent plug after
accessing the battery chamber. However, should the seals
not be clean or the vent plug left open and water enters
the battery chamber, your Seascooter will not be damaged
as it is designed for protection against accidental flooding.
If water enters the battery chamber :
1. Remove the SEASCOOTER™from the water if it is safe
to do so. Always observe safe diving practice.
2. Remove nose cone and tip out excess water.
3. Wait two minutes for any gases to dissipate, then
remove the battery.
4. If salt water has entered, rinse battery and battery
housing with fresh water.
5. Dry housing and battery thoroughly.
28 29
24 inches x 15.2 inches x 12.3 inches
(612 x 385 x 312 mm)
Unit Dimensions
-SEASCOOTER PRO-
Unit Weight 13 lb (6 kg) (with rechargeable battery)
Battery Type 1 x 12V / 7.5Ah rechargeable battery
Depth rating 20 m / 65 ft
Speed Up to 2.0 mph (3.2 km/h)
Battery Life /
Fully Charged
* Run up to 1 hour with normal use
∆
Continuous use up to 40 minutes
24 inches x 15.2 inches x 12.3 inches
(612 x 385 x 312 mm)
Unit Dimensions
-SEASCOOTER VS SUPERCHARGED PLUS-
Unit Weight 18 lb (8.2 kg) (with rechargeable battery)
Battery Type 1 x 12V / 12Ah rechargeable battery
Depth rating 30 m / 100 ft
Speed Up to 3.0 mph (4.8 km/h)
Battery Life /
Fully Charged
* Run up to 1.5 hours with normal use
∆
Continuous use up to 30 minutes (high Speed)
24 inches x 15.2 inches x 12.3 inches
(612 x 385 x 312 mm)
Unit Dimensions
-SEASCOOTER GTI-
Unit Weight 18 lb (8.2 kg) (with rechargeable battery)
Battery Type 1 x 12V / 12Ah rechargeable battery
Depth rating 30 m / 100 ft
Speed Up to 2.5 mph (4 km/h)
Battery Life /
Fully Charged
* Run up to 2 hours with normal use
∆
Continuous use up to 45 minutes

30
*Normal Use
The definition of normal use is based on the average general time
of use the user activates the seascooter in the water.
∆
Continuous Use
The definition of continuous use is based on a fully charged battery
whereby the seascooter is used continuously in the water without
stopping.
25.1 inches x 15 inches x 12.6 inches
(631 x 385 x 322 mm)
Unit Dimensions
-SEASCOOTER GTS-
Unit Weight 18 lb (8.2 kg) (with rechargeable battery)
Battery Type 1 x 12V / 12Ah rechargeable battery
Depth rating 30 m / 100 ft
Speed Up to 2.8 mph (4.5 km/h)
Battery Life /
Fully Charged
* Run up to 1.5 hours with normal use
∆
Continuous use up to 30 minutes
For more information on
Sea-Doo®Seascooter™Products
(Warranty, Customer Care / Maintenance,
Parts & Battery Purchase)
PLEASE VISIT
www.seadooseascooter.com
SEA-DOO®and the BRP logo are trademarks
of Bombardier Recreational Products Inc. or its affiliates,
used under licence by Stallion sport Ltd.
For more information on SEA-DOO®products visit www.sea-doo.com
Designed and manufactured by
Please visit our website at www.seadooseascooter.com to find out your local distributor.
All corresponding specification appear in this manual are correct at the time of printing.
For the latest updates and further information on the complete range of the Seascooter™,
PLEASE VISIT www.seadooseascooter.com

For any questions or queries you may have regarding your
SEA-DOO®SEASCOOTER™, please follow the below steps for
easy and fast resolution:
- STEP 1-
Please read your User Manual. For a copy of the User Manuals, please visit
www.seadooseascooter.com
- STEP 2-
Go to www.seadooseascooter.com and see our FAQ section to find instant
answers.
- STEP 3-
Contact one of our Customer Service representatives at the Customer Service
Center in your region.
RETURN / REPAIR PROCEDURE
1. Call the Customer Service Center for your Return / Repair Authorization
Number.
2. Make a copy of your Proof of Purchase (receipt).
3. Pack the defective unit in its original packaging including the polystyrene
foam and include the unit and all defective parts.
4. Attach the copy of your Proof of Purchase (receipt) to the outside of the box
(clearly visible), together with the Return / Repair Authorization Number.
5. Ship the package to the Service Center.
PLEASE NOTE: Deliveries that do not have the Proof of Purchase (receipt)
and Return / Repair Authorization Number attached clearly to the outside of
the box, will not be accepted by the Service Center.
UNITED STATES WEST, MEXICO & PUERTO RICO
SEA-DOO®SEASCOOTER™ CUSTOMER SERVICE CENTRE
Phone No.: [phone] Email: [e-mail]
UNITED STATES EAST SEA-DOO®SEASCOOTER™ CUSTOMER SERVICE CENTRE
Phone No.: [phone] Email: [e-mail]
CANADA SEA-DOO®SEASCOOTER™ CUSTOMER SERVICE CENTRE
Phone No.: [phone] Email: [e-mail]
HONG KONG SEA-DOO®SEASCOOTER™ CUSTOMER SERVICE CENTRE
Phone No.: [phone] Email: [email protected]
EMEA SEA-DOO®SEASCOOTER™ CUSTOMER SERVICE CENTRE
Please visit our website www.seadooseascooter.com for a listing of distributor
contacts in Europe, Middle East and Africa
(For other territories, please visit www.seadooseascooter.com
and contact your Local Distributor)
This warranty does not cover any product that has been subject to misuse
negligence or accident, or that has been operated in any way contrary to the
operating instructions as specified in the User Manual. Any flood, loss or
damage, for any reason, that is caused by accidental release and sinking of
the unit, or from flooding an o-ring sealed or water tight area will not be
covered under warranty. This warranty does not apply to any damage to the
product that is the result of improper maintenance or to any product that has
been altered or modified so as to change its intended use. This warranty does
not extend to repairs made necessary by normal wear or by the use of parts
or accessories which are either incompatible with the product or adversely
affects its operation, performance or durability.
In addition, this warranty does not cover items that
experience normal wear and tear.
ALL IMPLIED WARRANTIES ARE LIMITED IN THE DURATION TO THE
WARRANTY PERIOD. AND SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
OTHERWISE, ARE DISCLAIMED IN THEIR ENTIRETY AFTER THE
EXPIRATION OF THE APPROPRIATE WARRANTY PERIOD. THE
DISTRIBUTOR’S OBLIGATION UNDER THE WARRANTY IS STRICTLY
AND EXCLUSIVELY LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS AND RETURN OF THE PRODUCT TO THE
CUSTOMER. THE DISTRIBUTOR DOES NOT ASSUME OR AUTHORIZE
ANYONE TO ASSUME FOR THEM ANY OTHER OBLIGATION.
THE DISTRIBUTOR ASSUMES NO RESPONSIBILITY FOR INCIDENTAL,
CONSEQUENTIAL OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED
TO EXPENSE OF RETURNING THE PRODUCT TO THE DISTRIBUTOR,
LOSS OF USE OF PRODUCT AND LOSS OF TIME OR INCONVENIENCE.
EXCLUSIONS
BATTERY. This warranty does not include the battery.
CUSTOMER ENQUIRIES
If your unit is not operating, please refer to your User Manual before
contacting our Customer Service Center. For any damage or repair work
required, please do not return your product to the store where it was
purchased.
RETURN / REPAIR POLICY
Customers must call our Customer Service Center and ask for a Return /
Repair Authorization Number before sending the product to the Service
Center. Returned products must be shipped with original packaging including
the polystyrene packing material and all defective parts. Please contact our
Customer Service Center for assistance in handling your case.