Sealey FH2008 User manual

INSTRUCTIONS FOR:
FAN HEATER 2000W
MODEL: FH2008
Thank you for purchasing a Sealey Fan Heater. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.2. GENERAL SAFETY
 WARNING!Disconnect the heater from the mains power, before servicing or performing any maintenance. Servicing or
maintenance must only be carried out by an authorised service agent.
 Check that the heater is in sound condition and good working order. Take immediate action to repair or replace damaged parts.
 Use recommended parts only. Unapproved parts may be dangerous and will invalidate the warranty.
 WARNING! DO NOT use the heater near flammable material, liquids, solids, gases or compressed gas cylinders and the like.
 DO NOT obstruct the air inlet or outlet on the heater.
 DO NOT cover the heater.
 DO NOT operate the heater when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT touch the heater casing or grill when first switched off as these are hot and will take time to cool.
 DO NOT use the heater for anything other than its intended purpose. It is not suitable for drying clothes or laundry.
 DO NOT place the heater close to a bath, wash basin, shower, swimming pool or any other water-filled area or wet surface.
DO NOT get the heater wet or use in areas of high condensation.
 DO NOT place the heater up against any surface such as a wall, door or furniture etc.
 DO NOT place the heater immediately below any electrical outlet.
 DO NOT allow the power lead to lie in front of the heater outlet.
 DO NOT attempt to repair a damaged heater, contact an authorised service agent.
 DO NOT stand on the heater.
 DO NOT connect the fan heater to a timer device or other equipment that can automatically switch the heater on or off.
 Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
FH2008 ISSUE NO:1 18/07/08
1. SAFETY INSTRUCTIONS
1.1. ELECTRICAL SAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs,
sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the
installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main
distribution board. We also recommend that a Residual Current Device (RCD) is used. It is particularly important to use an
RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult a
qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about
electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before
connecting it to the power supply. See 1.1.1. and 1.1.2. and use a
Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check
all connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to
be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have
any faulty item repaired or replaced by a qualified electrician. When a BS 1363/A
UK 3 pin plug is damaged, cut the cable just above the plug and dispose of the
plug safely.
Fit a new plug according to the following instructions (UK only).
a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable
outer insulation extends beyond the cable restraint and that the restraint is tight. Double insulated products, which are
always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only. To rewire, connect the wires as
indicated above. DO NOT connect either wire to the earth terminal.
1.1.10.Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified
electrician to ensure that a suitably rated supply is available. We recommend that you discuss the installation of
an industrial round pin plug and socket with your electrician.
1.1.11. If an extension reel is used it should be as short as possible and fully unwound before connection. A reel with an RCD
fitted is preferred since any appliance plugged into it will be protected. The cable core section is important and should be
at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may
be used in the other output sockets, we recommend the use of 2.5mm²section cable.
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
FUSE RATING 13 AMP

4. MAINTENANCE
3.1. Position heater where required, either horizontally or
vertically on a level surface ensuring that the air
intake and outlet are not obstructed in any way.
3.2. Plug the heater into the mains supply.
3.3. Set the thermostat knob to the half way position as
shown in fig.1.
3.4. The fan heater will switch on when the selector switch
is set to one of the two power settings (1000W or 2000W).
3.5. Once the room reaches the set temperature the
heater will switch on and off automatically to maintain
that temperature. Adjust the position of the thermostat
knob to obtain a comfortable room temperature.
3.6. If the fan fails to operate when a power setting is
selected the thermostatic temperature control may be
set too low. Turn the knob slowly towards max until
the fan starts.
3.7. For a cooling effect turn the selector switch to the fan
only setting.
2. SPECIFICATIONS
Tough composite case with integral carry handle. Can be seated
in a vertical or horizontal position. Two-position heat settings,
control two 1000Watt heating elements. Full range ambient
room thermostat maintains temperature at pre-set level. Fan
doubles as cool air blower for use in the summer. Full CE
approval. Supplied with 13Amp non-rewirable ASTA approved
plug.
Model .......................................FH2008
Voltage/Frequency:......................... 230V ~50Hz
Power Rating:.............................1000/2000W
Heat Settings:.........................1000W or 2000W
Dimensions: ........................ 238 x 248 x 120mm
Weight: ........................................1.4kg
5. DECLARATION OF CONFORMITY
DECLARATION OF CONFORMITY We, the sole importer into the UK, declare that the product listed below is in conformity with the following
standards and directives
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products
18th July 2008
FAN HEATER
Model: FH2008
CE Marking Directive 93/68/EEC
RoHS Directive 2002/95/EC
WEEE Directive 2002/96/EC
Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC
Signed by Mark Sweetman
The construction file for this product are held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
01284 757500
01284 703534
[e-mail]
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
www.sealey.co.uk
Web
email
WARNING! Before attempting any maintenance ensure the unit is unplugged from the mains power supply and that it
is cool.
4.1. Clean the heater with a soft dry cloth. DO NOT use abrasives or solvents.
4.2. Periodically check the heater grille to ensure it is not blocked.
NOTE: This heater is fitted with a safety device which will cut the power should the heater overheat. If this happens you
should disconnect the heater from the mains supply for a minimum of 3 minutes allowing the heater to cool,
ensure the heater is not covered or anything is obstructing the vents. Plug the heater back into the electrical
socket and switch the heater back on.
No other maintenance is necessary. If you experience a problem with your heater or if the power lead or plug is damaged
contact your local authorised service agent for repair. DO NOT dismantle or tamper with the heater as this may be
dangerous and will invalidate your warranty.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
FH2008 ISSUE NO:1 18/07/08
3. OPERATION
Fig.1
2000W
MIN
MAX
1000W FAN ONLY
LAMP LIGHTS
WHEN HEATER
OPERATING
THERMOSTATIC TEMPERATURE
CONTROL