Sealey CP20VOP User manual

Ø125MM CORDLESS ORBITAL POLISHER 20V
- BODY ONLY
MODEL NO: CP20VOP
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure that Health & Safety, local authority and general workshop practice regulations are adhered to when using this
polisher.
9Familiarise yourself with the application, limitations and potential hazards of the polisher.
WARNING! Disconnect from the mains power and ensure that the pad is at a complete standstill before changing accessories,
servicing or performing any maintenance.
9Maintain the polisher in good condition (use an authorised service agent).
9Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
WARNING! Keep all guards and holding screws in place, tight and in good working order.
9Check regularly for damaged parts. A guard or any other part that is damaged must be repaired/replaced before the polisher is next
used.
9Use the polisher in a suitable work area and keep the area clean and tidy and free from unrelated materials. Ensure that there is
adequate lighting.
9Keep the polisher clean for best and safest performance.
9Before each use check all attachments for condition. If worn or damaged replace immediately.
9 Ensurethattherearenoammablematerialsneartheworkarea.
WARNING! Wear approved safety eye protection, ear defenders and, if dust is generated, respiratory protection.
9 Maintaincorrectbalanceandfooting.Ensurethattheoorisnotslipperyandwearnon-slipshoes.
9 Removeillttingclothing.Removeties,watches,ringsandotherloosejewelleryandcontainand/ortiebacklonghair.
9Keep children and unauthorised persons away from the work area.
9Avoid unintentional starting.
8DO NOT use the polisher for any purpose other than that for which it is designed.
8DO NOToperatethepolisherifanypartsaredamagedormissingasthismaycausefailureand/orpersonalinjury.
8DO NOTswitchthepolisheronuntiltheheadisincontactwiththepanelandswitchtheunito󰀨beforeremovingtheheadfromthe
panel.
8DO NOT use the polisher with abrasive cleaners or rubbing compounds as excessive paint removal may result.
8DO NOT get the polisher wet or use in damp or wet locations or areas where there is condensation.
8DO NOT allow untrained persons to operate the polisher.
8DO NOToperatethepolisherwhenyouaretiredorundertheinuenceofalcohol,drugsorintoxicatingmedication.
8DO NOTusethepolisherwherethereareammableliquids,solidsorgasessuchaspaintsolvents,etc.
8DO NOT leave the polisher operating unattended.
8DO NOTcarrythepolisherwithyourngeronthepowerswitch.
8DO NOT pull the cord from the power supply.
9 Useaqualiedpersontomaintainthepolisher.
9When not in use, unplug from the mains power supply and store in a safe, dry, childproof area.
2. INTRODUCTION
Digitaldisplayandvariablespeedcontrolfrom2100-5000rpm.15mmOrbitforgreaterpolishinge󰀩ciency.Featuresaslidebuttonon/o󰀨
switchallowingforasmoothcomfortablemainhandlegrip.Spindlelockforfastandeasypadchanges.Doubleinjectioncompositehousing
with rubber grip for added comfort. Requires Model No’s CP20VBP, CP20VBP2 or CP20VBP4 20V Battery and Model No. CP20VMC Mains
Charger.SuppliedwithØ125mmbackingpad.
3. SPECIFICATION
Model No:..............................................................CP20VOP
Battery: ................................................. 20V2Ah-6AhLi-ion
Free Speed: ....................................................2100-5000rpm
Noise Power/Pressure: ........................................ 86/75dB(A)
Pad Size: ................................................................ Ø125mm
Vibration/Uncertainty:......................................... 4.56/1.5m/s²
CP20VOPIssue106/05/20
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear protective
clothing
Wear a mask

4. OPERATION
WARNING! DO NOT immerse the polisher in water.
WARNING! Ensure that you read, understand and apply the safety
instructions in Section 1.
WARNING! Excess pressure can cause damage to paintwork and will put
the polisher motor under strain. Polishers with burnt out motors will be
 rejectedasawarrantyclaim.Normallytheweightofthepolisherissu󰀩cient.
WARNING! Ensure you read, understand and apply the safety instructions
in Section 1.
4.1. Ensure the power control switch is NOT switched to the on position before
 ttingthebattery.
4.2.  Holdthepolisherrmlywithonehandonthegripandkeeptheotherhand
on the end handle.
4.3. To select the required speed press the positive speed selector switch to the
appropriate speed.
4.4. Contact your Sealey stockist for details of compound heads and polishing
mop bonnets.
4.5. BACKING PAD EXCHANGE (FIG.2)
WARNING: Removebatterybeforetting/removingpadsormaintenanceis
carried out.
4.5.1. First detach the removable handle by removing the two plastic screws on
either side of the handle.
4.5.2. To remove the backing pad, press down chuck locking button under the
removable handle and manually unscrew the pad clockwise (when viewed
from above).
5. MAINTENANCE
WARNING! Before attempting any maintenance ensure the battery is
removed from the unit.
5.1. Keep the machine clean and dry. DO NOT use abrasives to clean the unit.
Ensure all external head screws are tight.
5.2.  Cleanregularlybyblowingajetofcompressedairthroughsideventsto
ensure motor ventilation is kept clear.
WARNING! Wear approved safety eye protection and, if necessary, respiratory
protection.
NOTE: Thefollowingmaintenancemustonlybecarriedoutbyatechnicallyqualied
person or an authorised Sealey service agent.
g.1
g.2
CP20VOPIssue106/05/20
Original Language Version
© Jack Sealey Limited

WARNING! – Risk of Hand Arm Vibration Injury.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
ThistoolissubjecttothevibrationtestingsectionoftheMachineryDirective2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measuredvibrationemissionvalue(a)............................4.56m/s²
Uncertaintyvalue(k):......................................................1.5m/s²
Pleasenotethattheapplicationofthetooltoasolespecialisttaskmayproduceadi󰀨erentaveragevibrationemission.Werecommendthata
specicevaluationofthevibrationemissionisconductedpriortocommencingwithaspecialisttask.
Ahealth and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for each tool.
NB:StatedVibrationEmissionvaluesaretype-testvaluesandareintendedtobetypical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB:ensurethatthelengthofleaderhosesissu󰀩cienttoallowunrestricteduse,asthisalsohelpstoreducevibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand Arm Vibration
Syndrome.
Health surveillance.
Werecommendaprogrammeofhealthsurveillancetodetectearlysymptomsofvibrationinjurysothatmanagementprocedurescanbe
modiedaccordingly.
Personal protective equipment.
Wearenotawareofanypersonalprotectiveequipment(PPE)thatprovidesprotectionagainstvibrationinjurythatmayresultfromthe
uncontrolleduseofthistool.Werecommendasu󰀩cientsupplyofclothing(includinggloves)toenabletheoperatortoremainwarmanddryand
maintaingoodbloodcirculationinngersetc.Pleasenotethatthemoste󰀨ectiveprotectionisprevention,pleaserefertothe
Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be found on the
HSCwebsitewww.hse.gov.uk-Hand-ArmVibrationatWork.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
BATTERY REMOVAL
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
SealeyLtdBatteriesProducerRegistrationNumber(BPRN)isBPRN00705.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty:Guaranteeis36monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
CP20VOPIssue106/05/20
Original Language Version
© Jack Sealey Limited