Seamaid 500699 User manual

You just bought the Lighting kit SeaMAID color from the SeaMAID range. Thank you for your trust.
Follow this guide and the online video for an easy and quick installation.
LIGHTING KIT SEAMAID COLOR
FOR ABOVE GROUND SWIMMING-POOL
500699 & 501498
> Installation guide

This kit is specially designed to be installed in an above ground swimming-pool with a rigid
walll provided with an outlet fitting. It includes a lighting system, a RGB LED lighting system,
a 4 functions radio remote controller, a 6 meters low voltage power supply cable and a
230V/12VAC transformer
Remote
controller Front cover Outlet fitting Support Wall inlet 12 VAC Electric cable 12 VAC Transformer
1 2 3 4 5 6 7
Caution: the minimum distance
between the swimming-pool and the
provided transformer must be 3,50 m
in use

2
1
3
4
5 6 7
> Presentation of the product
Model 500699

> Installation
A step by step assistance
1. Remove the front cover (2) by pressing with
fingers on the clips
2. Unscrew the outlet fitting (3) and remove it from
the wall inlet (5)
3. Instal the back support (4) adjusting the top hole
on the wall inlet (5)
4. Re-screw the outlet fitting (3) and hands tighten
against the pool wall (4). (In certain cases, you can glue
the gasket on the back support (4) to enhance its position)
5. Replace the front cover (1) by adjusting first the
top hook and then press on the clips to guide it
to a correct position against the support.
6. Connect the cable to the provided transformer
(7) by hand gripping the plug (It is recommended
to take off the top rail and place the cable under
it)
7. Connect the transformer (7) to a secure 220/230
VAC outlet and connected to the ground, the
projector illuminates
5. Process to the remote controller pairing for the
model 500699

> Installation
A step by step assistance
Recommendations :
Before any installation, it is important to ensure that the pool is provided with a compatible
outlet fitting. Do not use in flexible PVC walled or freestanding pool.
The 230V/12VAC transformer which feeds the system must be connected to a protected outlet
at a minimum distance of 3.50 meters from the pool, protected against water splash and
connected to the ground.
It is strictly prohibited to touch the transformer with wet hands or any other contact surface.
Ensure that nobody stands in the pool during installation.
After each use, it is recommended to disconnect the transformer from the socket.

> Use
10 programs model with remote controller
> The use of the remote controller requires a positioning face to the lamp at a
maximum distance of 10 meters, unfolded antenna. Metallic part close to the
projector or a too deep immersion may restrict the remote controller use at a very
short distance.
In this case, it is also possible to change programs using the on/off switch of the
electric supply power of the projector. A cut of the current of less than 2 seconds
makes the program change. After a cut of the current for over 10 seconds, switch on
restarts from the last program used.
Manual program including 7 static colours and 3 controlled atmospheres
with the provided remote controller.
Recommandations :
In all cases, refer to the leaflet
provided with the
product.
In case of difficulty during the
installation or use, it is
recommended to watch
the installation video
and to read the FAQ on
our website.

Buttons functions :
O > Off/On
S > Synchronization
C > Colour selection
P > Programs selection
For the first remote controller use, it is necessary to pair
it with the projector
Tip : to make pairing easier, you can connect the
transformer to a multisocket equipped with a on/off
switch and pair it before installing the projector in the
pool
1. Switch on the projector and switch it off more than 20
seconds with the general electric power.
2. Make fast ON/OFF twice, and switch on the projector.
3. Insert the provided battery
4. Press the buttons O et S together on the remote
controller.
5. The projector flashes several times and stays on, the
pairing process is confirmed.
> Remote controller
RGB model 500699

> SeaMAID, proof of quality and reliability
> Quality: SeaMAID products are developed exclusively by our French R&D team then
manufactured in China and marketed after a rigorous quality-control.
SeaMAID products range is certified TÜV Rheinland thus proving the safety and quality of
the proposed products.
> Reliability : Each SeaMAID product is guaranteed 24 months in standard exchange.
Thanks to an exclusive development, the optics brings a confort in the use of the
products; plastic parts are soldered by friction thus ensuring a perfect seal.