Sebo ET-1 User manual

SEBO ET-1 Owner's Manual
Technical Details
Brush motor - 175 watts, 1.6 amps
Width: 12 in
Weight: 5.4 lbs
Brush roller: replaceable
Brush drive: toothed belt with electronic overload protection
Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
When using an electrical appliance, basic precautions must always be followed.
To reduce the risk of electric shock, this brush machine has a polarized plug; one blade is wider than the
other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not
change the plug in any way. Connect only to the outlet type specified on the serial number plate
underneath the machine.
SAVE THESE INSTRUCTIONS.
WARNING: To reduce the risk of fire, electric shock, or injury:
1. Do not leave vacuum while plugged in. Unplug from outlet when not in use and before servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not use near small children or pets. Do not allow to be used as a toy. Use of this product by children should always be
supervised by an adult.
4. Use only as described in this manual. Use only manufacturer-recommended attachments.
5. Do not use with a damaged cord or plug. If vacuum is not working as it should, has been dropped, damaged, left outdoors, or
dropped into water, take it to a SEBO service center.
6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not
run vacuum over cord. Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug � not the cord.
8. Do not plug in if switch is in the �I� (ON) position.
9. Do not use outlets above counters to plug in vacuum � damage to items in the surrounding area could occur.
10. Always carry the vacuum over steps and sills.
11. Do not handle plug or vacuum handle with wet hands.
12. Do not put any object into vacuum openings. Do not use machine with any openings blocked. Keep openings free of lint, hair,
and anything that may reduce air flow.
13. Do not re-use filter (dust) bags or wash the filters.
14. Do not remove any screws from vacuum.
15. Do not vacuum up anything that is burning or smoking, such as cigarettes, matches, or hot ashes. 16. Do not use vacuum
without dust bag and/or filters in place.
17. Turn off all machine controls before unplugging.
18. Use extra care when cleaning on stairs.
19. Do not use machine to vacuum up flammable or combustible liquids such as gasoline or use in areas where they may be
present.
20. Machines can cause a fire when operated near flammable vapors or materials. Do not operate this vacuum near flammable
fluids, dust or vapors.
21. Maintenance and repairs must be done by qualified personnel.
22. Use only original SEBO replacement parts.
23. Do not use vacuum as a step.
24. Do not leave machine standing in one place with machine turned on.
25. While the vacuum is in use, the power cord should be unwound from the cable reel at least two thirds of its length. Hold plug
when rewinding onto the cord reel. Do not allow plug to whip while rewinding.
26. Keep hair, loose clothing, fingers, and all parts of body away from vacuum openings and moving parts. Do not place fingers
or other body parts under vacuum unless it is unplugged.
27. Do not place the power head over rug edges or fringe.
28. The vacuum has a manual reset thermal protector. The protector is reset by switching off the vacuum. The thermal protector
needs some time to cool down after switching off! Check the vacuum for air blockages or mechanical failures before switching
on.
29. Store the vacuum in a dry place at room temperature. When the vacuum is not in use, the cord should be wound on the cord

reel.
30. Any other servicing should be performed by an authorized service representative.
31. The hose contains electrical wires. Do not use if damaged, cut, or punctured. Avoid picking up sharp objects.
32. Always unplug vacuum before connecting or disconnecting either hose or power head.
33. Use this power head only in combination with a SEBO vacuum cleaner or central vacuum system.
34. Do not connect power head to a malfunctioning or damaged vacuum.
Special Product Features
Your SEBO ET-1 and ET-2 Power Heads are designed for use with the SEBO C3.1 and K3 canister vacuum
cleaners and central vacuum units. The SEBO C3.1 and K3 vacuums equipped with ET-1 or ET-2 Power
Heads are among the most technically advanced canister vacuum cleaner systems in the world. For
example, the ET-1 and ET-2 Power Heads have warning systems and automatic shut-off capabilities that
are designed to alert the user to machine problems that, if ignored, will damage the machine or diminish
performance.
Your SEBO ET-1 and ET-2 Power Heads most unique features are:
1. Deep Cleaning. SEBO power heads offer deep cleaning of your carpets only a thorough brushing
can give.
2. Wider L-shaped Head. The wider head allows for optimal cleaning and maneuverability around
furniture and under cabinets, and the extension side of the head cleans and brushes right to the
edge.
3. Brush On/Off Switch. The green �power� light positioned on top of the power head is also an
on/off switch. By depressing it, you may manually turn on or off the brush on the power head for
cleaning hard floors or carpet. 4. Brush Roller Obstruction � Auto Shut-Off. If the brush roller is
obstructed, the power head will shut off in three seconds, the amber light located on top of the
power head will illuminate, and the brush rollers will stop rotating. The user should turn the power
switch off, unplug the machine, and immediately remove the obstruction. If the user restarts the
machine without removing the obstruction, the power head will again shut off and the amber light
will turn on.
5. Manual Height Adjustment. The ET-1 and ET-2 power head brush height may be adjusted for
high carpet (dial setting 4) and progressively lower to bare floor (dial setting 1). The amber light
located on top of the power head will illuminate if the height setting is too high or if the brush roller
is worn. Dial down to the next number until the amber light turns off.
6. Stationary Use. When the machine has its handle in the upright-locked position, it is designed to
shut off the brush roller. The green light does not illuminate in the upright position. The green light
will illuminate only in the operating position. An operating power head should not stand stationary
on the floor for inappropriate periods of time.
Attaching the Power Head to the Telescopic Tube of Sebo C3.1/K3
1. Find the connection tab (A) at the base of the
telescopic tube (B).
2. Move the connection tab (A) OUT away from the tube (C). See
enlarged detail below. It will only move approximately 1/8-inch.
NOTE: the tab must not be forced beyond the �flush� position of
the collar. Proceed to step 3.
3. Insert the base of the telescopic tube (E) into the power head
swivel neck (3). Make sure that the connection tab (A) is properly
aligned with the connection plug (4) in the swivel neck. Damage to
the connection may occur if the tab and the plug are not properly
aligned.

Operating Instructions
Starting The Machine - Figures 1 & 2
A. Before turning on your canister, make sure that the vacuum handle is in
its upright locked position (figure 1).
1. With the canister main power switch in the OFF position, and the power
control slider on the handle (#11, figure 2) in the OFF position, pull the
power cord out from the base of the canister (see canister owner�s
manual). The power cord should be unwound from the cable reel at least
two thirds of its length.
2. Plug the polarized power cord into a 120 volt outlet located near the
floor.
3. Press the main power switch on the base of the canister gently with your
foot or hand to the ON position.
4. Slide the Power Control Slider (#11, figure 2) to the ON position (the
slider will �click� when it is pushed out of the OFF position). It will then
slide freely between 0 suction and MAX suction. Set the slider to the suction
desired. The green light does not illuminate in the upright position (figure
1). The green light will illuminate only in the operating position.
Operating The Machine - Figure 3
B. When the power head is switched on with the handle in the
upright locked position (see figure 1 above), the brush roller will
not spin. To release the power head from the upright locked
position, press down on the foot pedal (#8, figure 3) and lower
the handle into the normal operating position. The brush roller
will then start spinning and the green light on the power head
will illuminate.
The handle can be lowered to a horizontal position useful for
vacuuming under beds.
You may adjust the suction control with the power control slider
as you vacuum different surfaces or when using the accessory
tools. For optimal cleaning and brushing, operate the machine at
the maximum suction power setting and push the power head slowly over the carpet.
When the canister�s main power switch is in the ON position, you may turn the power head off and on
with the power control slider (#11, figure 2). To turn the power head off using the power control slider,
pull the slider to 0 suction, then continue pulling the slider up until it �clicks� into the OFF position.
The green power head light will then shut off.
Always turn the power off on both the canister and the power head when changing heads or
unplugging the vacuum. Slide the power control slider on the power head to its OFF position, press
the main power switch on the base of the canister gently with your foot or hand, then unplug the
canister to completely shut down the power when changing heads or storing the vacuum. Hold the plug
while rewinding the cord onto the cord reel. Avoid letting the plug whip while rewinding.
WARNING! The quality, condition, coating, texture, age and manufacturing technique of all floor
surfaces vary. Therefore, vacuums with rotating brushes, including your SEBO, may damage some floor
coverings or surfaces. Some types of high-gloss hardwood floors, cushion vinyl, berber carpets, long
shag, and delicate or hand- oven carpets are particularly vulnerable to damage by rotating brushes.
When possible, consult the materials supplied by your flooring manufacturer for information on proper
upkeep and cleaning. To ensure that your new SEBO vacuum cleaner is compatible with your floor,
please test the vacuum cleaner on each type of flooring surface in a small inconspicuous area to
determine if any damage occurs. If damage occurs, stop using the vacuum cleaner immediately!

The Brush Height Adjustment Feature -Figure 4
To manually adjust the brush height, rotate the dial (#2) for high carpet (dial setting 4) and
progressively lower to bare floor (dial setting 1). The amber light located on top of the power head (#5)
will illuminate if the height setting is too high. Dial down to the next number until the amber light turns
off. If the amber light does not turn off, the brush roller may be worn.
Indicator Lights - Figures 5, 6 & 7
The use of a power head is recommended for the optimal cleaning of
carpets. The rotating of the swivel neck (#3, figure 5) allows the power
head to move in any direction.
By pushing the foot pedal (#8, figure 6) and lowering the handle, you
activate the power head and the brush begins spinning. Failure to use the
foot pedal will cause lasting damage to the machine. The electronic brush
control constantly monitors the status of the brush, communicating the
status through the lights on top.
Green and Amber Light: The brush is not fully engaged in the (#5 and #6,
figure 7) carpet. The height adjustment should be lowered. If the height
adjustment is at its lowest setting, the brush is worn and needs to be
replaced.
Green Light Only: Brush is working well. We strongly (#6, figure 7)
recommend selecting a brush height that is only one level beneath that at
which both the green and amber lights are on. For maximum cleaning
performance, the brush height adjustment can be lowered to its lowest
setting.
Amber Light Only: The brush is blocked. Turn off the machine, (#5, figure
7) unplug it, and then remove the blockage. To clean delicate or hard floor
surfaces, the power head is equipped with an on/off switch (#6, figure 7).
When this switch is used to turn off the brush roller, the green indicator
light is also turned off.
Maintenance
Always unplug vacuum from outlet before dismantling any part of the machine!
Removing the Brush Roller - Figure 8
To remove the brush roller, press the button marked �PRESS� (#10)
and turn the brush roller end cap downward. Turn the brush (#12)
slightly to the right and pull it out. We recommend regular removal of
threads and hair which have wound around the brush roller.
Cleaning the Brush Roller 12
Unplug the vacuum before attempting to clean the brush. The brush
should be cleaned regularly. Fibers and hair can be pulled out of the
brush while manually rotating the roller, or the roller can be removed
from the power head to clean it.

Clog Removal
Always unplug vacuum from outlet before dismantling any part of the machine!
Clogs in the Airflow Pathway - Figure 9
Many clogs can be removed by accessing the airflow pathway via the
orange colored access door (#13, figure 9) located on the underside of
the power head.
Clogs in the Swivel Neck
Check the swivel neck regularly for blockages. Do not open the machine.
To check for a clog in the swivel neck (#3, page 5), remove the
telescopic tube by pressing the release button (#9, page 5). Pull the
tube out of the swivel neck. Push the obstruction down the neck with a
stick or long screwdriver and remove it through the orange access door (#13, figure 9). For clogs not in
the power head, please refer to your canister vacuum owner�s manual.
Troubleshooting Guide
Always unplug brush machine from outlet before dismantling any part of the machine!
Problem
Reason(s)
Solution
Does not turn
on.
Not plugged into good outlet.
Use another outlet.
Cable worn.
Replace cable
The power control slider switch is set
to the O (off) position.
Slide slider switch to ON position.
The switch on the power head is off
Press the switch
The internal switch in the swivel neck
is off because the machine is in the
upright locked position
Release the foot pedal and lower the
telescopic tube to operating level
Amber and
green lights
are both on
Brush worn
Replace brush
Reduced brush action
Brush is not fully in contact with the
floor
No lights are
illuminated
Machine is in upright locked position
and roller is shut off
Release the foot pedal and lower the
telescopic tube to operating level
The switch on the power head is off
Press the switch
The internal switch in the swivel neck
is off because the machine is in the
upright locked position
Release the foot pedal and lower the
telescopic tube to operating level
Amber light is
on and brush
stops spinning
Jammed brush roller
Remove brush roller obstruction
Clog in airflow pathway or swivel neck
Remove clog
Overload shut down from excessively
deep but loose carpet pile
If carpet pile is too deep and loose,
then use a shag rake attachment
instead of the ET-1 or ET-2

Warranty Information
Three Year Non-Wear Parts - Five Year Motor - One Year Labor
1. Your authorized SEBO dealer or SEBO will provide the original product purchaser with replacement of
Non- Wear Parts which fail due to a material or workmanship defect for a period of three (3) years from
the original date of purchase of new product. SEBO America will provide a five (5) year warranty on
suction motors and brush drive motors.
2. Your authorized SEBO dealer or SEBO will repair (or SEBO will cover labor charges associated with
repair) a defective SEBO power head at no cost to the original purchaser, within one (1) year of original
purchase of new product.
3. SEBO America, Floor Care Equipment, Ltd., or an authorized SEBO dealer must complete all warranty
repairs.
4. To locate an authorized SEBO dealer in your area, or to register a warranty claim in the United
States of America, please call SEBO America at (303) 792-9181.
5. To locate an authorized SEBO dealer in your area, or to register a warranty claim in Canada, please
call Floor Care Equipment, Ltd. at (403) 250-5005
6. The warranties provided for above apply exclusively to SEBO power heads which are used
residentially. No warranty is provided for SEBO power heads used commercially.
7. The Wear Parts excluded from warranty coverage include the brush rollers, the front bottom plate
and the rear bottom plate.
8. This warranty applies only while your SEBO power head is physically located within the United States
of America and its territories or Canada.
9. The purchase receipt showing the date, price, and item of purchase is the initial document of proof of
purchase and determines the validity of warranty. To be certain that your warranty claim can be
processed as quickly and efficiently as possible, please retain your original purchase receipt and mail in
the warranty card provided with your new SEBO power head or vacuum cleaner.
10. This warranty gives you specific legal rights. You may also have other legal rights, which vary from
state/province to state/province.
11. SEBO America will not process nor will it accept responsibility for warranty claims for machines
purchased from dealers located in Canada. Floor Care Equipment, Ltd. will not process nor will it accept
responsibility for warranty claims for machines purchased from dealers located in the United States.
EXCLUSIVE REMEDY: The remedies provided under the terms of this warranty are the purchaser's
exclusive remedies and are in lieu or any other remedies otherwise available.
THE WARRANTY DOES NOT COVER:
- Used or secondhand products.
- Products outside of the warranty period.
- Items not manufactured by Sebo.
- Normal maintenance service.
- Equipment damaged by improper use, accident, other casualty or negligence.
- Machines equipped with non-authorized attachments or modifications.
- Machines on which the serial number has been altered or removed.
Limitations and exclusions:
Sebo makes no other representations or warranties, expressed or implied and specifically excluded the
implied warranties of merchantability and fitness for a particular purpose.

Sebo will not be liable for incidental or consequential damages of any kind or nature.
This disclaimer of implied warranties shall not apply to the extent said disclaimer is not allowed by
applicable state/provincial law.
To contact Sebo in the United States:
Sebo America, LLC
Telephone: 303-792-9181
Fax: 303-792-9196
Website: www.sebo.us
� Copyright Sebo America, LLC - All Rights Reserved
Other manuals for ET-1
5
Table of contents
Other Sebo Vacuum Cleaner manuals

Sebo
Sebo Airbelt K3 User manual

Sebo
Sebo Airbelt K3 User manual

Sebo
Sebo Airbelt D User manual

Sebo
Sebo AIRBELT E1 BOOST User manual

Sebo
Sebo 370 comfort User manual

Sebo
Sebo Automatic X4 User manual

Sebo
Sebo Professional D User manual

Sebo
Sebo *# User manual

Sebo
Sebo FELIX User manual

Sebo
Sebo ESSENTIAL G User manual

Sebo
Sebo BS 36 Comfort Quick guide

Sebo
Sebo AIRBELT K User manual

Sebo
Sebo 370 comfort User manual

Sebo
Sebo 370 comfort User manual

Sebo
Sebo Essential G4 User manual

Sebo
Sebo Professional G1 User manual

Sebo
Sebo DART 3 User manual

Sebo
Sebo Felix Premium User manual

Sebo
Sebo 370 comfort User manual

Sebo
Sebo Felix Premium User manual