Seconique Furniture Corona User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped o ffimmediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
CARE AND MAINTENANCE
Page 01
CORONA 5' TABLE
FOR DOMESTIC USE ONLY
SEC/SH/01/22/KK1

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
PARTS LIST
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
S400-403-007-KK1-01 Table Top 11/2
Table Leg (Blue Marking)
Table leg (Yellow Marking)
Short Frame Side
Long Frame Side
S400-403-007-KK1-02
S400-403-007-KK1-03
S400-403-007-KK1-04
S400-403-007-KK1-05
2
2
2
2
2/2
2/2
2/2
2/2
Page 02
1
5
4
5
2
3
4
2
3
SEC/SH/01/22/KK1

4,0 x 40
Ø1/4" x 120
10 x 40
1/4"
FITTINGS
TOOLS REQUIRED
Page 03
12
01
08
01
08
08
D
E
F
A
B
C
GLUE
SEC/SH/01/22/KK1

Ø1/4" x 120
Ø10 x 40mm
STEP 1
STEP 2
Page 04
4 - x2
SHORT FRAME SIDE
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
D08
2 - x2
TABLE LEG(BLUE MARKING)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A04
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
D
Glue must be added to
the dowel holes on
parts 4 and 5.
3 - x2
TABLE LEG(YELLOW MARKING)
5 - x2
LONG FRAME SIDE
5 - x2
LONG FRAME SIDE
D
D
D
D
x2
x2
5
4
YELLOW
A
YELLOW
3
E04
F01
1/4"
GLUE
Glue must be added to
the dowel holes on
parts 2 and 3.
E
A
E
BLUE
ADD GLUE
x2
5
2
SEC/SH/01/22/KK1

Ø1/4" x 120
STEP 3
STEP 4
Page 05
4 - x2
SHORT FRAME SIDE
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A02
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Glue must be added to
the dowel holes on
parts 2 and 3.
E02
F01
1/4"
GLUE
Glue must be added to
the dowel holes on
parts 2 and 3.
A
ADD GLUE
A
YELLOW
YELLOW
BLUE
BLUE
E
4
E
4
ADD GLUE
A
A
E
E
ADD GLUE
Ø1/4" x 120
A02
E02
F01
1/4"
GLUE
YELLOW
YELLOW
BLUE
SEC/SH/01/22/KK1

STEP 5
STEP 6
Page 06
1 - x1
TABLE TOP
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
ADD GLUE
C12
4,0 x 40
FOR YOUR FUTURE
REFERENCE
ORDER NUMBER
SHOULD BE HERE
XXXXX
CENTRALIZE
C
C
CC
C
C
C
C
C
C
C
C
SEC/SH/01/22/KK1
C