Seconique Furniture Winsdor Stowaway Dining Table User manual

WINDSOR STOWAWAY DINING TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF SERVICE IF YOU FOLLOW THE
GUIDELINES FOR ITS SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS PRODUCT. ITS USE WILL
INVALIDATE ANY CLAIM YOU MAY HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE NECESSARY TO TIGHTEN
UP THE FIXINGS FROM TIME TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXINGS.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET). DO NOT USE POLISH, DETERGENT
OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A PLACE MAT UNDER HOT OR
MARKING.
COLD ITEMS TO PREVENT
FOR DOMESTIC USE ONLY
PAGE 1 OF 2
DO NOT
USE
SEC/SH/08/18/PU1

PAGE 2 OF 2
PLEASE CHECK THAT YOU HAVE ALL THE PARTS
LISTED BEFORE YOU START ASSEMBLING. IF YOU
DO FIND THAT SOMETHING IS MISSING, DO NOT
CONTINUE ASSEMBLY. PLEASE CONTACT YOUR
SUPPLIER IMMEDIATELY.
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE ANY CLAIM AND MAY
DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PARTS LIST
PART
1
2
A
B
C
D
QTY
1PCS
4PCS
1
1
BOX
QTY
8PCS
8PCS
8PCS
1PC
DESCRIPTION DESCRIPTIONPART
TABLE TOP
TABLE LEG
JCBC SCREW M6X 60MM (RB)
SPRING WASHER
FLAT WASHER
ALLEN KEY
HARDWARE LIST
STEP 1
Place the table top (1) upside down on a soft, clean surface, then attach the table
legs (2) using JCBC screw (A), Spring Washer (B) & Flat Washer (C). Tighten using
Allen Key (D).
1
2
2
2
2
2
22
2
A
B
D
C
C
1
WINDSOR STOWAWAY DINING TABLE
ASSEMBLY INSTRUCTIONS
SEC/SH/08/18/PU1

IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF SERVICE IF YOU FOLLOW THE
GUIDELINES FOR ITS SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS PRODUCT. ITS USE WILL
INVALIDATE ANY CLAIM YOU MAY HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE NECESSARY TO TIGHTEN
UP THE FIXINGS FROM TIME TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXINGS.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET). DO NOT USE POLISH, DETERGENT
OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A PLACE MAT UNDER HOT OR
MARKING.
COLD ITEMS TO PREVENT
FOR DOMESTIC USE ONLY
PAGE 1 OF 2
DO NOT
USE
WINDSOR STOOLS
ASSEMBLY INSTRUCTIONS
SEC/SH/08/18/PU1

PAGE 2 OF 2
THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE ANY CLAIM AND MAY
DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING. IF YOU DO FIND THAT SOMETHING IS MISSING, DO NOT
CONTINUE ASSEMBLY. PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
STEP 1
STEP 2
22
1
1
2
6
44
44
44
55
333
4
5
5
PARTS LIST (FOR ONE CHAIRS)
NO.
1
2
3
4
5
6
NO.
A
B
C
D
E
QTY
1PC
2PCS
1PCS
1PC
1PC
1PC
QTY
6PCS
6PCS
6PCS
8PCS
1PC
DESCRIPTION DESCRIPTION
CHAIR BACK JCBC SCREW M6 X 50MM
SIDE STRETCHERS SPRING WASHER M6 X 13.5MM
M6 FLAT WASHER
FRONT SECTION
CUSHION SEAT
BOTTOM STRETCHER (LEFT)
BOTTOM STRETCHER (RIGHT)
CB SCREW M4 X 32MM
ALLEN KEY M4 X 30 X 115MM BALL SHAPE
HARDWARE LIST (FOR ONE CHAIRS)
EB
C
2
4 - LEFT
PHILLIPS
SCREWDRIVER
PHILLIPS
SCREWDRIVER
DA
Please lay down the Chair Back (1) on smooth surface. Attach
the Side Stretchers (2) as shown. Use JCBC Screw (A), Spring
Washer (B), Flat Washer (C) and tighten using Allen Key (E).
Please repeat for both sides.
Then attach the Bottom Stretcher - Left (4) to the Chair Back (1) .
Fasten (4) to (1) with screw (D).Use a Phillips screwdriver to
tighten it.
22
1
EA
DD
BC
Attach Front Section (3) to Side Stretchers (2), Bottom
Stretcher (4) and (5). Fasten (3) to (2)with JCBC Screw (A)
and Spring Washer (B) and Flat Washer (C). Use Allen Key (E)
to tighten (A).
Fasten (3) to (4) & (5) with screw (D). Use a Phillips
Screwdriver to tighten it.
Fully tighten all the bolts and screw at this time.
222333
444
STEP 2
3
6
D
D
2
Place the Cushion Seat (6) bottom- side up on an elevated
surface. Position the chair frame assembly with the legs
facing up as shown.
Centre the Chair Frame to the Cushion Seat (6). Use a
Phillips Screwdriver (Not provided) to drive screw(D) to
fasten the seat to the Chair Frame.
444
PHILLIPS
SCREWDRIVER
1
445
STEP 3
WINDSOR STOOLS
ASSEMBLY INSTRUCTIONS
SEC/SH/08/18/PU1
LEFT
RIGHT
RIGHT
LEFT