Seconique 400-401-173 User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped o ffimmediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
CARE AND MAINTENANCE
Page 01
SALVADOR 1+4 TILE TOP
FOR DOMESTIC USE ONLY
SEC/SW/07/21/KK1
DINING TABLE
GREY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
PARTS LIST
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
S400-401-173-KK1-01T Table Top 12/2
Table Leg (Blue)
Table Leg (Yellow)
Long Frame Side
Short Frame Side (Smaller)
S400-401-173-KK1-02T
S400-401-173-KK1-03T
S400-401-173-KK1-04T
S400-401-173-KK1-05T
2
2
2
2
1/2
1/2
2/2
2/2
Page 02
SEC/SW/07/21/KK1
BLUE
RED
BLUE
YELLOW
YELLOW
1
2
2
5
5
3
3
4
4

3,5 x 35
Ø7 x 100
10 x 40
FITTINGS
TOOLS REQUIRED
Page 03
SEC/SW/07/21/KK1
10
04
04
08
01
01
D
E
F
A
B
C
GLUE
Ø7 x 70

STEP 1
STEP 2
SEC/SW/07/21/KK1
Page 04
4 - x2
LONG FRAME SIDE
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
F08
2 - x2
TABLE LEG(BLUE)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A04
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
F
Glue must be added to
the dowel holes on
parts 4 and 5.
3 - x2
TABLE LEG(YELLOW)
4 - x2
LONG FRAME SIDE
5 - x2
SHORT FRAME SIDE
F
F
x2
5
D01
GLUE
Glue must be added to
the dowel holes on
parts 2 and 3.
x2
BLUE
YELLOW
2
3
4
ADD GLUE
A+E
A+E
10 x 40
Ø 7 x 70
Ø 7 x 100
Ø7 x 100
F
F
x2
4

STEP 3
STEP 4
SEC/SW/07/21/KK1
Page 05
5 - x2
LONG FRAME SIDE
PARTS REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Glue must be added to
the dowel holes on
parts 2 and 3.
Glue must be added to
the dowel holes on
parts 2 and 3.
ADD GLUE
YELLOW
BLUE
B+E
5
B+E
5
TOOLS REQUIRED
HARDWARE REQUIRED
B02
D01
GLUE
Ø7 x 70
Ø 7 x 70
Ø 7 x 100
B02
D01
GLUE
Ø7 x 70
B+E
YELLOW
BLUE
B+E
BLUE
Ø 7 x 70
Ø 7 x 100
BLUE

STEP 5
STEP 6
SEC/SW/07/21/KK1
Page 06
1 - x1
TABLE TOP
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
C10
3,5 x 35
C
C
C
C
CC
C
C
C

ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped o ffimmediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
CARE AND MAINTENANCE
Page 01
SALVADOR 1+4 DINING CHAIR
FOR DOMESTIC USE ONLY
SEC/SH/08/21/KK1
GREY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
PARTS LIST
Part Code
Part Number Part Description Quantity Carton
01
02
03
04
05
06
S400-401-173-KK1-01C Front Leg 21/1
Back/Front Rail
Stretcher
Side Seat Rail
Back Leg
Seat Pad
S400-401-173-KK1-02C
S400-401-173-KK1-03C
S400-401-173-KK1-04C
S400-401-173-KK1-05C
S400-401-173-KK1-06C
2
2
2
2
1
1/1
1/1
1/1
1/1
1/1
Page 02
07 Back Rail
S400-401-173-KK1-07C 11/1
01
01
02
03
03
04
04
02
07
06
05
05
SEC/SH/08/21/KK1

Ø 7 x 80
FITTINGS
TOOLS REQUIRED
Page 03
08
04
01
04
08
01
E
F
G
A
B
C
Ø 7 x 60
GLUE
3,5 x 35
04
D
4,0 x 40
SEC/SH/08/21/KK1
10,0 x 40

STEP 1
STEP 2
Page 04
03 - x2
STRETCHER
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A01
1 - x2
FRONT LEG
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
Glue must be added to
the dowel holes on
parts 03 and 04.
3 - x2
STRETCHER
4 - x2
SIDE SEAT RAIL
F08
AF
04 - x2
SIDE SEAT RAIL
GLUE
A01
G
Ø 7 x 80
Ø 7 x 60
03
04
01
03
04
05
5 - x2
BACK LEG
B
B
B04
Ø 7 x 80
G04
4,0 x 40
GLUE
A
SEC/SH/08/21/KK1
10,0 x 40

Ø7 x 60
C04
STEP 3
STEP 4
Page 05
2 - x2
BACK/FRONT RAIL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
C04
Ø 7 x 90
7 - x1
BACK RAIL
Ø 7 x 80
Ø 7 x 60
07
02
02
C
C
C
C
C
CC
C
Ø 7 x 80
Ø 7 x 60
SEC/SH/08/21/KK1

STEP 5
STEP 6
Page 06
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
D04
06
D
D
DD
3,5 x 35
SEC/SH/08/21/KK1