Seconique CORONA NEST OF TABLES User manual

CORONA NEST OF TABLES
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
FOR DOMESTIC USE ONLY
SEC/SW/05/21/MY1
Page 01

Part Code
Part Number Part Description Quantity Carton
01
02
03
04
05
06
07
08
09
10
11
S300-303-010-MY1-01 Top Panel (Large) 11/1
Front/Rear Panel (Large) (560mm)
Side Panel (Large) (325mm)
Leg Natural (Large)
Leg Green (Large)
Top Panel (Medium)
Front/Rear Panel (Medium) (420mm)
Side Panel (Medium) (270mm)
Leg Natural (Medium)
Top Panel (Small)
S300-303-010-MY1-02
S300-303-010-MY1-03
S300-303-010-MY1-04
S300-303-010-MY1-05
S300-303-010-MY1-06
S300-303-010-MY1-07
S300-303-010-MY1-08
S300-303-010-MY1-09
S300-303-010-MY1-10
S300-303-010-MY1-11
2
2
2
2
1
2
2
2
2
1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
Leg Green (Medium)
PARTS LIST
SEC/SW/05/21/MY1
Page 02
12
13
14
15
Front/Rear Panel (Small) (280mm)
Side Panel (Small) (215mm)
Leg Green (Small)
S300-303-010-MY1-12
S300-303-010-MY1-13
S300-303-010-MY1-14
S300-303-010-MY1-15
2
2
2
2
1/1
1/1
1/1
1/1
Leg Natural (Small)
01
01
202
202 03
03
04
04
05
05
06
07
07
08
08
09 09
10
10
11
13
13
12
12
14
14
15
15
avoid damage.
during assembly.
* Please check carton contents and read the
instructions before commencing assembly.
* Please take care to avoid damaging panels
enclosed instructions carefully.
* Assemble this product following the
* Use of power tools to assemble this product
will invalidate any claim and damage this
* Please assemble on a clean soft surface to
product making it unsafe !!!

Ø 8 x 30mm E02
FITTINGS
TOOLS REQUIRED
Page 03
FITTINGS
SEC/SW/05/21/MY1
Ø 3,5 x 35mm
C
B
A
24
36
16 Ø 5 x 90mm
D24
GLUE

STEP 1
STEP 2
SEC/SW/05/21/MY1
Page 04
02- x2
FRONT/REAR PANEL (LARGE)(560mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
07- x2
FRONT/REAR PANEL (MEDIUM)(420mm)
03 - x2
SIDE PANEL (LARGE)(325mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
08 - x2
SIDE PANEL (MEDIUM)(270mm)
B
E
Please assemble on
a clean soft surface
to avoid damage.
202
07
12
B
B
B
B
B
B
03
08
13
BB
B
B
B
B
B
B
B
B
B
B
B
E
Please assemble on
a clean soft surface
to avoid damage.
13 - x2
SIDE PANEL (SMALL)(215mm)
12- x2
FRONT/REAR PANEL (SMALL)(280mm)
B24
Ø 8 x 30mm
E01
GLUE
B12
Ø 8 x 30mm
E01
GLUE
Glue must be added to the
dowel holes on part
02, 07, 12.
Glue must be added to the
dowel holes on part
03, 08, 13.

STEP 3
STEP 4
SEC/SW/05/21/MY1
Page 05
02- x2
FRONT/REAR PANEL (LARGE)(560mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
04- x2
LEG NATURAL (LARGE)
03 - x2
SIDE PANEL (LARGE)(325mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
05- x2
LEG GREEN (LARGE)
E
Glue must be added to the
dowel holes on part
04 and 05.
04
202
05
D
D
2x
D04
E01
GLUE
Ø 5 x 90mm
GREEN
Please assemble on
a clean soft surface
to avoid damage.
E
Glue must be added to the
dowel holes on part
04 and 05.
03
03
D
D
D
D
D04
E01
GLUE
Ø 5 x 90mm
2x

STEP 5
STEP 6
SEC/SW/05/21/MY1
Page 06
01 - x1
TOP PANEL (LARGE)
PARTS REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
E
Glue must be added to the
dowel holes on part
01.
Please assemble on
a clean soft surface
to avoid damage.
C08
01
01
A
A
A
A
TOOLS REQUIRED
HARDWARE REQUIRED
A06
E01
GLUE
Ø 3,5 x 35mm
CC
C
C
C
C
C
C
C
C

STEP 7
STEP 8
Page 07
07- x2
FRONT/REAR PANEL (MEDIUM)(420mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
09- x2
LEG NATURAL (MEDIUM)
08 - x2
SIDE PANEL (MEDIUM)(270mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
10- x2
LEG GREEN (MEDIUM)
E
Glue must be added to the
dowel holes on part
09 and 10.
D
D
2x
D04
E01
GLUE
Ø 5 x 90mm
GREEN
Please assemble on
a clean soft surface
to avoid damage.
E
Glue must be added to the
dowel holes on part
09 and 10.
08
08
D
D
D
D
D04
E01
GLUE
Ø 5 x 90mm
2x
09
10
07
420mm
270mm
270mm
SEC/SW/05/21/MY1

STEP 9
STEP 10
Page 08
06 - x1
TOP PANEL (MEDIUM)
PARTS REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
E
Glue must be added to the
dowel holes on part
06.
Please assemble on
a clean soft surface
to avoid damage.
C08
01
06
A
A
A
A
TOOLS REQUIRED
HARDWARE REQUIRED
A06
E01
GLUE
Ø 3,5 x 35mm
CC
C
C
C
C
C
C
C
C
SEC/SW/05/21/MY1

STEP 11
STEP 12
Page 09
12- x2
FRONT/REAR PANEL (SMALL)(280mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
14- x2
LEG NATURAL (SMALL)
13 - x2
SIDE PANEL (SMALL)(215mm)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
15- x2
LEG GREEN (SMALL)
E
Glue must be added to the
dowel holes on part
14 and 15.
D
D
2x
D04
E01
GLUE
Ø 5 x 90mm
GREEN
Please assemble on
a clean soft surface
to avoid damage.
E
Glue must be added to the
dowel holes on part
14 and 15.
13
13
D
D
D
D
D04
E01
GLUE
Ø 5 x 90mm
2x
14
15
12
280mm
215mm
215mm
SEC/SW/05/21/MY1
GREEN

STEP 13
STEP 14
Page 10
11 - x1
TOP PANEL (SMALL)
PARTS REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
E
Glue must be added to the
dowel holes on part
11.
Please assemble on
a clean soft surface
to avoid damage.
C08
01
11
A
A
A
A
TOOLS REQUIRED
HARDWARE REQUIRED
A06
E01
GLUE
Ø 3,5 x 35mm
CC
C
C
C
C
C
C
C
C
SEC/SW/05/21/MY1