Seconique BLACK WOOD GRAIN LISBON User manual

BLACK WOOD GRAIN
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF
SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND
PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE
FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS
PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND
COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME TO TIME. THIS IS
COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET)
DO NOT USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A
PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT MARKING.
FOR DOMESTIC USE ONLY
IMPORTANT
LISBON SHOE CABINET
ASSEMBLY INSTRUCTIONS
Page 01
SEC/SH/01/21/EU2
DO NOT
USE

4
1
3
2
5
PART LIST
Part Number Part Code Part Description Quantity Carton
1
2
3
4
5
6
S100-120-015-EU1-01
Right Side Panel
Left Side Panel
Back Crossbar
Front Crossbar
Top Panel
11/1
1
1
1
1
2
1/1
1/1
1/1
1/1
1/1
S100-120-015-EU1-02
S100-120-015-EU1-03
S100-120-015-EU1-04
S100-120-015-EU1-05
S100-120-015-EU1-06
6
6
8
8
8
7
7
7
7
8Drawer Front
Shelf Panel 12
3
1/1
1/1
S100-120-015-EU1-07
S100-120-015-EU1-08
Back Panel
Page 02
SEC/SH/01/21/EU2

HARDWARE LIST
A
B
C
D
E
F
G
H
I
DOWEL 6 X 30MM
BOLT M7 X 60MM
6 PCS
SCREW M3.5 X 12MM
ALLEN KEY
CAM BOLT+CAM NUT 4 SETS
BOLT M6 X 50MM
PLASTIC FOOT
2 PCS
2 PCS
J
K
L
M
N
O
P
Q
40 PCS
TACK 26 PCS
2 PCS
PLASTIC H STRIP 1 PC
SCREW M4 X 16MM
SHOE TRAY RACK
ANTI-TIP STRAP
SCREW M5.5 X 12MM 6 PCS
PVC AIR HOLE
SCREW M3.5 X 16MM
HANDLE
HANDLE SCREW 19MM
8 PCS
6 PCS
4 PCS
3 PCS
1 PC
6 SETS
2 PCS
2 PCS
K
K
K
TAKE OUT THE THREE PARTS SHOWN
BELOW FROM EACH SHOE RACK (K)
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
THE CAM LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.
Page 03
SEC/SH/01/21/EU2

STEP 1
PARTS REQUIRED
1 - LEFT SIDE PANEL x1
HARDWARE REQUIRED
A
H02
STEP 2
02
PARTS REQUIRED
4 - RIGHT SIDE PANEL x1
H
K
K
K
K
A
H
A
1
K03
K03
TOOLS REQUIRED
HARDWARE REQUIRED
A
H02
02
K03
K03
TOOLS REQUIRED 4
Page 04
SEC/SH/01/21/EU2

STEP 3
PARTS REQUIRED
2 - FRONT CROSSBAR x1
HARDWARE REQUIRED
STEP 4
5 - TOP PANEL x1
5
H
A
A
A
H04
04
3 - BACK CROSSBAR x1
TOOLS REQUIRED
1
2
3
Page 05
SEC/SH/01/21/EU2
2
3
B
D
PARTS REQUIRED
1 - LEFT SIDE PANEL x1
2 - FRONT CROSSBAR x1
3 - BACK CROSSBAR x1
HARDWARE REQUIRED
D01
TOOLS REQUIRED
B01

STEP 6
J
E
Page 06
SEC/SH/01/21/EU2
STEP 5
4
PARTS REQUIRED
HARDWARE REQUIRED
D01
TOOLS REQUIRED
B01
4 - RIGHT SIDE PANEL x1
J04
E04
B
D
PARTS REQUIRED
5 - TOP PANEL x1
HARDWARE REQUIRED
TOOLS REQUIRED
5
H

STEP 7
STEP 8
Page 07
SEC/SH/01/21/EU2
N
M
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
6 - BACK PANEL x2
N01
M02
6
6
PARTS REQUIRED
C
Q
HARDWARE REQUIRED
TOOLS REQUIRED
C06
Q26
6
6

STEP 9
STEP 10
Page 08
SEC/SH/01/21/EU2
K
J
K
7
7
FINISHED
FRONT
EDGE
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
J06
K06
7 - SHELF PANEL x3 X3
X3
FINISHED
FRONT
EDGE
7
J
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
J06
7 - SHELF PANEL x3 X3
X3
X3

STEP 11
STEP 12
Page 09
SEC/SH/01/21/EU2
J
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
12
8 - DRAWER FRONT x3
J
PARTS REQUIRED
X3
8
F
I
X3
X3
HARDWARE REQUIRED
TOOLS REQUIRED
F03
I06
J
X3

STEP 13
STEP 14
Page 10
SEC/SH/01/21/EU2
HARDWARE REQUIRED
TOOLS REQUIRED
K06
L06
K
J
KJ
X3
PARTS REQUIRED
X3
L
L
HARDWARE REQUIRED
TOOLS REQUIRED
J12
PARTS REQUIRED
7 - SHELF PANEL x6
7
7
7
K
K

STEP 15
Page 11
SEC/SH/01/21/EU2
P
02
WARNING
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
PART REQUIRED
HARDWARE REQUIRED
O
02
TOOLS REQUIRED
O
P
TOP
TOP
WALL
WALL
TOP
O