Seville Classics airLIFT OFF65944B/48B User manual

1
airLIFT® 2-Button Electric Height Adjustable
Standing Desk
Please contact Seville Classics for help with assembly and
to report any damaged or missing components.
Phone: [phone]
Email: [e-mail]
Homepage: www.SevilleClassics.com
Model #: OFF65944B/48B
013021

1
Safety Instructions
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND
OPERATING INSTRUCTIONS AND WARNINGS REGARDING THE USE OF THIS PRODUCT MAY
RESULT IN SERIOUS BODILY INJURY
 Read and understand this manual before attempting to install or
 Assure that everyone who uses this product is informed of the contents of this manual.
This is the responsibility of the Purchaser.
 Not intended for use by young children or for those persons who require supervision.
 Do not open any of the components – legs, control box, or controller. There is a risk of electric shock.
 Assemble desk on a at and level surface.
Use & Liability
Safe use of this product is possible only when the operating instructions are read completely and the instructions con-
tained are strictly observed. Persons who do not have the necessary experience or knowledge of this product must
not use the product. Persons with reduced physical or mental abilities should not use this product, unless they are
under supervision or they have been thoroughly instructed in the use of the apparatus by a person who is responsi-
ble for the safety of these persons. Children should be closely supervised to ensure that they do not play with this
product.
Before You Begin
Layout all components and hardware. Visually examine and make sure components are free of damage. If there is
visual damage to any component, it must not be installed.
Two people are needed to turn or move the desk and some of it’s components. When moving or turning the assem-
bled desk, grab the legs, not the desk top.
Make sure to assemble on a soft and non-abrasive surface to avoid scratches.
Check all connections and cables. Make sure control box is connected to a power outlet.
If the control box makes unusual noises or emits an odor, switch power o immediately.
The desk MUST be INITIALIZED before rst use.
Read the INITIALIZATION chapter prior to operation.

2
Quick Setup!
Only takes 15 minutes to complete. Phillips screwdriver required.
Keep the top in the box during assembly to protect it from scratches.
Legs
Feet
Top
Controller Box
Motor

3
Parts List
A. Top (1)
B. Legs (1)
C. Feet (2)
D. Controller (1)
Please make sure you have all the parts on this list.
Leave the TOP (A) in the box during assembly.
If you’re missing parts, contact us for replacements at [phone] or send an email
to [email protected]
Tools & Hardware List
E. M6x12 Screw (4)
F. ST 4.8x13 Screw (4)
G. M8x30 Screw (8)
H. 4 mm Hex Key (1)
I. 5 mm Hex Key (1)
J. Zip Tie (1)
K. Pre-Installed Fastener (2)

4
STEP 1. Lower LEGS (B) onto the back of the TOP (A). Make sure the motor is on
the same side as the control box.
Control Box
Motor
STEP 2. Align the holes on the legs with the brackets and attach with M6x12
SCREWS (E) using 4 mm HEX KEY (H).

5
STEP 3. Align holes on crossbar with holes on back of TOP (A).
Attach with two ST4.8x13 SCREWS (F) using Phillips screwdriver.
STEP 4. Align holes on CONTROLLER (D) with holes on edge of TOP (A).
Attach with two ST4.8x13 SCREWS (F) using Phillips screwdriver.
Organize cables with ZIP-TIE (J) and FASTENERS (K).

6
STEP 5. Connect cables from the motor to the CONTROLLER (D).
Connect cables from motor to control box.
STEP 6. Attach FEET (C) to the bottom of table legs with four M8x30 BOLTS (F) using
5 mm HEX KEY (I).

7
Take this time to make sure all screws, bolts, and cables
have been secured tightly.
STEP 7. Plug the power cable into the control box. Make sure the cables from the
controller to the motor to the control box are securely attached.
Power cable

8
WARNING: TWO PEOPLE ARE NECESSARY TO TURN TABLE.
DESK IS HEAVY. LIFT WITH EXTREME CAUTION.
STEP 8. Turn the desk onto its feet.
DO NOT put weight on desk yet.
Lift with 2 people
TIP: Screw the leveling feet in and out as necessary to
ensure the desk stands level.

9
Use Instructions
DESK MUST BE INITIALIZED BEFORE FIRST USE
Initialize & Reset
Press and hold the Down Arrow until the desk reaches its lowest point.
Initialization is complete when the desk emits a chime sound and rebounds.
When RST appears on the display, follow the above instructions to reset.
Adjust Height
Press and hold the Up Arrow to lift.
Press and hold the Down Arrow to lower.
Up Arrow Down Arrow

10
Troubleshooting
Problem Acon
Desk does not go up or down and the controller
does not illuminate when any button is
pressed.
Check all connections. Make sure power cord is plugged into the control box
and a power outlet. Press any button on the controller and make sure it illumi-
nates. Reset the desk.
Desk does not go up or down and the
controller illuminates when any
button is pressed.
Unplug the power cord and re-plug after 10 seconds.
Reset the desk. If the problem persists, switch motor cables from one port to
another at control box and reset again.
Desk wobbles excessively. It is normal that desk moves slightly at standing height when in use. Retighten
all screws and bolts, and adjust leveling feet to make sure table stands level.
Desk legs are noisy. It is normal that desk makes noise when the stages move past each other.
Apply silicon-based lubricant if it is unusually noisy.
Please contact customer service for additional support.
Phone: [phone] | Email: [e-mail]

11
Warranty Information
7-Year Non-Electronic Component Warranty
Seville Classics, Inc. warrants to the original retail purchaser that if this product proves to be defective in
material or workmanship, we will replace the aected non-electronic part(s) for a period of seven years
on Seville Classics airLIFT® Electric Height-Adjustable Standing Desks from the date of
original purchase.
2-Year Electronic Component Warranty
Seville Classics, Inc. warrants to the original retail purchaser that if this product proves to be defective in
material or workmanship we will replace the aected electronic part(s) for a period of two years on
Seville Classics airLIFT® Electric Height Adjustable Standing Desks from the date of original purchase.
Except for the express warranty set forth above and except to the extent prohibited by applicable law,
Seville Classics grants no other express or implied warranties with respect to the product, its tness for
any purpose, its quality, or its merchantability. The liability of Seville Classics under the warranty shall be
limited to the amount paid by the customer for the product. Seville Classics shall not be liable for any loss
of use of the product, or other incidental or consequential costs, expenses or damages incurred by the
customer or other user.
This warranty covers only the airLIFT® Electric Height Adjustable Standing Desks sold in the United States
of America and Canada. Some states do not allow the exclusion or limitations of implied warranties or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives
you specic legal rights, and you may also have other rights that vary from state to state.
During the applicable warranty period, Seville Classics, at its option, will either refund the original pur-
chase price or replace the aected part(s) with comparable part(s) when the aected part(s) are
returned, postage prepaid, to the address below:
Seville Classics Inc.
19401 South Harborgate Way
Torrance, CA 90501 – 1322 U.S.A.
To obtain service under this warranty, you must:
1. Register your product at www.SevilleClassics.com/warranty
2. Contact our customer service at [phone] or email [e-mail];
3. Return the aected part(s) postage prepaid to Seville Classics pursuant to our customer service
representative; and
4. Include in the package:
A. A copy of the original bill of sale, your charge or credit receipt, or other satisfactory proof of
the date of the original purchase date of the product, and the price paid; and
B. A short detailed description of the problem, the name and phone number of the contact
person.

12
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced Radio/TV technician for help
MADE IN CHINA
Seville Classics, Inc. / 19401 Harborgate Way Torrance, CA 90501 / USA