Sauder New Grange 420021 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-24
Français p 25-28
Español p 29-32
Lot # 391194 06/07/16
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
4-Drawer Chest
New Grane Collection | Model 420021
WARNING
CHOKING HAZARD - Small Parts
Not for children under 3 years.
Adult assembly required.

Table of Contents Assembly Tools Required
3
4-5
6-24
25-28
29-32
33-34
35
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
420021 www.sauder.com/servicesPae 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
D30 DRAWER RIGHT SIDE (4)
D31 DRAWER LEFT SIDE (4)
D183 DRAWER BACK (4)
D988 DRAWER BOTTOM (4)
E SIDE SKIRT (2)
F BRACE (1)
G TOP FRONT MOLDING (1)
H TOP LEFT MOLDING (1)
I TOP RIGHT MOLDING (1)
J BACK (1)
K BOTTOM FRONT MOLDING (1)
L BOTTOM LEFT MOLDING (1)
M BOTTOM RIGHT MOLDING (1)
M67 DRAWER BRACE (4)
N LARGE BACK (1)
O DRAWER FRONT (4)
P LEFT PLINTH (1)
Q RIGHT PLINTH (1)
Now you know
our ABCs.
420021www.sauder.com/services Pae 3
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
E
D30
M67
D31
D988
D183

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
5L WARNING LABEL - 1
(Refer to the last step for proper
location and application)
WA RNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
•Place heaviest items in the lowest drawers.
• Unless specifically desined to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or han on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
31G CORNER BRACKET - 4
SAFETY STRAP - 1
Locate this nylon SAFETY
STRAP (60M) to be used
later in assembly. Do not
accidentally throw away.
60M
SAFETY DRYWALL
ANCHOR - 1
61M
35AA UNIVERSAL CABINET RAIL - 8 35AC DRAWER RIGHT - 4 35AD DRAWER LEFT - 4
HIDDEN CAM - 12
1F CAM DOWEL - 10 2F CAM SCREW - 2 8F MOLDING
CONNECTOR - 2
17F
METAL BRACKET - 4
4G 127K KNOB SET - 8
WASHER - 1
13M
NAIL - 26
1N METAL PIN - 2 1R
420021 www.sauder.com/servicesPae 4

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 9/16" LARGE HEAD SCREW - 31
1S 3S GOLD 5/16" FLAT HEAD SCREW - 32
12S BROWN 1" FLAT HEAD SCREW - 3 BROWN 1-1/2" FLAT HEAD SCREW - 7 14S
BLACK 2-1/4" FLAT HEAD SCREW - 4
26S 30S BLACK 1-9/16" FLAT HEAD SCREW - 20
SILVER 1/2" MACHINE SCREW - 8
38S
420021www.sauder.com/services Pae 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å Push ten HIDDEN CAMS (1F) into the ENDS (A and B),
BRACE (F), and DRAWER BRACES (M67). Then, insert the
metal end of a CAM DOWEL (2F) into each HIDDEN CAM.
420021 www.sauder.com/servicesPae 6
A
B
F
M67
M67M67
M67
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
(10 used)
Arrow
1F
2F
Do not tihten the HIDDEN CAMS in this step.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1801
to watch a video on how to assemble your unit.

StepStep 2
å Push two HIDDEN CAMS (1F) into the BACK (J) with the
arrows in the HIDDEN CAMS pointin toward the edes
of the BACK.
å Turn two CAM SCREWS (8F) into the exact holes shown
in the ENDS (A and B).
420021www.sauder.com/services Pae 7
A
B
J
Arrow
1F
8F
1F
Arrow
Some assembly
(and snacks) required.

Step
å Fasten the UNIVERSAL CABINET RAILS* (35AA) to
the ENDS (A and B). Use sixteen GOLD 5/16" FLAT
HEAD SCREWS (3S) throuh holes #1 and #3.
å *patent pendin lide system
Step 3
420021 www.sauder.com/servicesPae 8
GOLD 5/16" FLAT HEAD SCREW
(16 used in this step)
3S
3
2
1
1
2
3
VIEW THE DRAWER GLIDE VIDEO
3
2
13
2
13
2
1
1
2
31
2
31
2
3
Glide end
Glide end
A
B

StepStep 4
å Fasten two METAL BRACKETS (4G) to the BACK (J). Use
two BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the METAL BRACKETS are even with the
edes of the BACK.
å Fasten the BACK (J) to the LEFT END (B). Tihten one
HIDDEN CAM and use one BLACK 9/16" LARGE HEAD
SCREW (1S) throuh the METAL BRACKET and into the
LEFT END.
420021www.sauder.com/services Pae 9
BLACK 9/16" LARGE HEAD SCREW
(3 used in this step)
1S
4G
4G
1
2
B
J
J
Surface with HIDDEN CAMS
Surface
with
HIDDEN
CAMS
Surface with HIDDEN CAMS
Ede with
CAM DOWELS

Step
å Insert two METAL PINS (1R) into the exact holes shown in
the ENDS (A and B).
å Fasten the BRACE (F) to the LEFT END (B). Tihten one
HIDDEN CAM.
å NOTE: Be sure the METAL PIN in the LEFT END inserts
into the BRACE.
Step 5
420021 www.sauder.com/servicesPae 10
B
A
F
Surface with HIDDEN CAMS
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
1R
1R
Do not stand the unit upriht
without the LARGE BACK
fastened. The unit may collapse.
Caution

StepStep 6
å Fasten the RIGHT END (A) to the BRACE (F) and BACK (J).
Tihten two HIDDEN CAMS and use one BLACK 9/16" LARGE
HEAD SCREW (1S) throuh the METAL BRACKET and into the
RIGHT END.
å NOTE: Be sure the METAL PIN in the RIGHT END inserts into
the BRACE.
420021www.sauder.com/services Pae 11
J
F
A
Arrow
Minimum
190 derees
Maximum
210 derees
Surface
without
HIDDEN
CAMS
Ede with
CAM DOWELS
BLACK 9/16" LARGE HEAD SCREW
(1 used for the METAL BRACKET)
1S

Step
å Tap two MOLDING CONNECTORS (17F) into the notches
in the TOP MOLDINGS (G, H, and I).
Step 7
420021 www.sauder.com/servicesPae 12
Flat end
Flat end
Use your hammer to tap the MOLDING CONNECTORS (17F) into the notches in the TOP MOLDINGS.
H17F
17F
I
G
Flat surface
Flat surface
Flat surface
Don't worry. It isn't
Rome. This can be built
in a day.

StepStep 8
å Carefully flip the TOP MOLDINGS (G, H, and I) over.
å Fasten the TOP MOLDINGS (G, H, and I) to the TOP (C). Use
seven BROWN 1-1/2" FLAT HEAD SCREWS (14S).
å NOTE: Do not overtihten the SCREWS into the TOP.
å Fasten one end of the SAFETY STRAP (60M) to the TOP (C).
Use one BLACK 9/16" LARGE HEAD SCREW (1S).
420021www.sauder.com/services Pae 13
BLACK 9/16" LARGE HEAD SCREW
(1 used for the SAFETY STRAP)
1S
60M
BROWN 1-1/2" FLAT HEAD SCREW
(7 used in this step)
14S
I
H
GC
Surface
with holes

Step
å Fasten the ENDS (A and B) to the TOP MOLDINGS (H
and I). Tihten four HIDDEN CAMS.
Step 9
420021 www.sauder.com/servicesPae 14
I
HG
B
A
Arrow
Minimum
190 derees
Maximum
210 derees

å Fasten the BOTTOM (D) and BOTTOM MOLDINGS (L
and M) to the ENDS (A and B). Use four BLACK 2-1/4"
FLAT HEAD SCREWS (26S).
å NOTE: The BOTTOM MOLDINGS will wrap around the
bottom of the unit.
StepStep 10
420021www.sauder.com/services Pae 15
B
A
L
M
D
Surface with
more holes
These holes must be here.
Flat surface
Anled ede
BLACK 2-1/4" FLAT HEAD SCREW
(4 used in this step)
26S
Anled ede
26S
26S
Flat surface

Step
å Fasten the BOTTOM FRONT MOLDING (K) to the BOTTOM (D).
Use three BROWN 1" FLAT HEAD SCREWS (12S).
Step 11
420021 www.sauder.com/servicesPae 16
D
K
Anled ede
Flat surface
Anled ede
BROWN 1" FLAT HEAD SCREW
(3 used in this step)
12S

å Fasten two METAL BRACKETS (4G) to the PLINTHS (P and Q) in the
exact holes shown. Use two BLACK 9/16" LARGE HEAD SCREWS (1S).
å NOTE: Be sure the METAL BRACKETS are even with the edes of
the PLINTHS.
å Fasten four CORNER BRACKETS (31G) to the SIDE SKIRTS (E) exactly
as shown. Use eiht BLACK 9/16" LARGE HEAD SCREWS (1S).
StepStep 12
420021www.sauder.com/services Pae 17
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
1S
4G
P
Q
E
E
31G
31G
Curved ede

Step
å Fasten the SIDE SKIRTS (E) to the PLINTHS (P and Q)
exactly as shown. Use four BLACK 9/16" LARGE
HEAD SCREWS (1S).
Step 13
420021 www.sauder.com/servicesPae 18
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
P
Q
E
E
Curved ede
If you're doin this to
help a friend, don't
leave without a bite.

å Fasten the SIDE SKIRTS (E) and PLINTHS (P and Q)
to the BOTTOM MOLDINGS (K, L, and M). Use eiht
BLACK 9/16" LARGE HEAD SCREWS (1S) throuh the
BRACKETS and into the BOTTOM MOLDINGS.
StepStep 14
420021www.sauder.com/services Pae 19
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S
P
Q
E
EM
L
K
This hole will
not be used.

StepStep 15
420021 www.sauder.com/servicesPae 20
å Carefully turn your unit over onto its front edes. Unfold the LARGE
BACK (N) and lay it over your unit.
å Make equal marins alon all four edes of the LARGE BACK (N). Push on
opposite corners of your unit if needed to make it "square".
å Fasten the LARGE BACK (N) to the BACK (J) usin four BLACK 9/16"
LARGE HEAD SCREWS (1S). Turn the SCREWS a few turns but do not
completely tihten them.
å Push the LARGE BACK down slihtly toward the bottom of the unit and
fasten the upper and side edes of the LARGE BACK (N) to your unit usin
the NAILS (1N).
å Now, completely tihten the four SCREWS (1S) alon the bottom ede of
the LARGE BACK (N).
Finished surface
NAIL
(26 used in this step)
1N
Do not stand the unit upriht
without the LARGE BACK
fastened. The unit may collapse.
Caution
N
J
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
1S
This hole must be here.
Printed
information
must be
facin up.