Secure TRACKSO ELITE 103-2 User manual

TRACKSO INSTALLATION GUIDE FOR SECURE METER ELITE 103 -2,ELITE 303-2,ELITE 307-2
Brand: Secure
Type: METER
Models: ELITE 103-2, ELITE 303-2, ELITE 307-2
CONNECTION DIAGRAM
On the rear panel, Secure Elite Elite 103-2, ELite 303-2,Elite 307-2 has an RS-485 communication socket as shown in the following
figure.
Figure S1 –Rear view of Secure Elite 103-2,ELite 303-2,Elite 307-2
1. Please unscrew the RS485 terminal as shown in Figure S1.
2. Connect the cables to the RS485 bus terminal blocks.
3. Please make the connections from Terminal Block chip to TrackSo IoT
Gateway as mentioned in the Table –ST1.
Table ST1 –Secure RS485 chip connections
with TrackSo IoT Gateway
Secure Pin No. &
Assignment
TrackSo Pin No. &
Assignment
1
A
3
D+
2
B
4
D-
3
SG
-
-
DEFAULT CONFIGURATION IN TRACKSO IOT GATEWAY
Inverter ID: 1 (Range: 1 to 247)
Baud Rate: 9600 (Default) (Values: 9600, 19200, 38400)
Data Bits: 8
Stop Bit: 1
Parity: N/A (None)
CONFIGURATION AT THE METER END
The Setup Mode can be used to configure the meter with the help of push buttons: The Setup Mode is password protected which
can be accessed only by users authorized to change the configurations
Password Entry
The following steps will guide you to access the Setup Menu:

From the default display mode, simply press & button once to access the
following Setup Mode page.
In the above display page, when the selection bar ‘ -→’ is on the ‘Set Up’ option, press
button to confirm the selection of Setup Menu. This will give access to the
following password entry prompt screen:
(i) Display after correct password entry
At the password prompt enter the 4-digit password (default password is ‘0000’) using
and buttons. After completing the entry, press button to confirm. Correct
password gives access to the 1st page of configuration mode, see figure (i). An
incorrect password will display ‘Incorrect’ message as shown in figure (ii).
(ii) Display after incorrect password entry
In case you have entered incorrect password, the display will automatically return to
the Setup Mode page (as shown in step 1) in 5 seconds or alternatively, press
button to return to Setup Mode immediately

SETTING BAUD RATE
This is the 4th option on the 1st page of Setup Menu. The ‘Communication’ option can be used to configure the baud rate and the
MODBUS identification number. To select it, move selection bar to ‘COMM’ option and then press . The page shown in the
following figure will appear:
Baud Rate
This is the 1st option on ‘Communication’ page. When the selection arrow is on ‘BD
RATE’, press to access the next page for entering the baud rate
To exit the ‘COMM’ page and return to the Setup menu, move the selection bar over the
‘Quit’ option and then press button.
With the help of left/right button select the baud rate from the below specified range and
then press to confirm the selection.
Configurable baud rates: 1200, 2400, 4800, 9600, 19200, 38400 bps
SETTING DEVICE ID
MODBUS ID
This is the 2nd option on ‘Communication’ page. To select it, move the selection arrow
on ‘MODBUS ID’ option and then press . The display page shown on the left appears.

Enter the desired ID from the following permissible range and then press to confirm
and save the selection.
Configurable MODBUS ID range is 1 to 247.
At the end of configuration updates, select the ‘Save’ option to activate the above new
configurations in the meter. To return to the previous page, press or wait for 5
seconds.
CONNECTING MULTIPLE METER

INSTALLATION VIDEO
Scan the QR code to view
the video
Video Link: https://www.youtube.com/watch?v=fenEDMIrACM