Secure SSP 302 Operating instructions

SSP 302
Socket Energy Monitor
User and Installation
Instructions
BGX501-921-01

out of range
controller cannot
communicate directly
with device
SSP Repeater
Z-Wave
Controller
Lamp Load
Secure SSP 302
Socket Energy Monitor
The Secure SSP 302 forms part of
a Z-Wave Plus™ home automation
network.
SSP 302 is a mains-powered,
plug-in device that supports energy
monitoring. It is suitable for
switching loads up to 3kW at 230V
AC. It can measure voltage,

Button
FLASH
current, power, energy etc. The
SSP 302 acts as a repeater in a
Z-Wave network and helps other
device messages to reach a
destination.
SSP 302 is a fully compliant
Z-Wave Plus™ device that will
work with other manufacturer’s
Z-Wave devices.
Installation
Step 1:
Unpack and
insert the
SSP 302 into
the wall socket.
Ensure that the
red-coloured
network status
3

LED is flashing (once per second).
Note:
If the network status LED is not
flashing check the following.
•Ensure wall socket switch is on.
•Press the top button, the relay
status LED should switch ON
and glow green.
•If the relay status LED does not
glow then the device is not
functioning.
•It is possible that the SSP 302
was part (joined) of another
network previously; if so, exclude
it before including it in this
network. Refer to step-2 for the
exclusion process.

Avoid locations alongside or behind
large metal surfaces that could
interfere with the low power radio
signals between the unit and the
controller.
Step-2: Z-Wave Plus™
commissioning
To include the
SSP 302 onto
a network, put the
controller into
inclusion mode.
Now, press and
hold the button on
SSP 302 for 4 to 7
seconds then
release. The network
FLASH
FLASH
5

status LED will start flashing (twice
per second) on successful start of
inclusion process.
Note: Refer to the controller’s
manual for controller relevant
actions.
On successful inclusion the LED
will turn off.
The total process can take up to 20
seconds (Refer to the “Technical
specifications – Radio” section for
details).
If the device fails to join the
network it will go back to factory
default state and the Network
status LED will start flashing once
per second.

If there is an issue with RF
Communication, then re-locate the
device and repeat the
commissioning process again.
To exclude the SSP 302 from a
network, put the controller into
exclusion mode (refer to controller
instructions) and follow the same
sequence as per the
commissioning process for include
node. After successful exclusion
the network status LED will start
flashing once per second, and the
device will reset to factory default.
If exclusion fails, SSP 302 network
status LED will turn off after about
5 seconds.
7

Note: Exclusion works when the
device is in direct range with the
controller (no repeater allowed).
Associating SSP 302 in a
Z-Wave Network
(follow steps 3 to 5)
Note: Association process works
only after device included onto
network.
Step 3: Put the controller into
Association Mode.
Note: Some controllers can
automatically associate. Always
check with the manufacturer’s
manual.
Step 4: Press and hold the
SSP 302 button for more than 1

second, but less than 4 seconds,
and then release.
Step 5: The controller will confirm
association when the process is
successfully completed.
9

Combined
Button & LEDs
Green LED: ON
power switched to
front socket
Green
LED
*Socket type
will vary with
country
Appliance Socket
Press the SSP 302 button (less
than one second) to supply power
to its socket. By default, the green
LED will be lit when the supply is
On.

The socket type will vary with
country. The figure shows the UK
variant.
Ensure that the appliance plug is
firmly plugged into the appliance
socket.
Over Current Protection
If the current exceeds the limit for
more than 30 seconds the load will
be disconnected. To reconnect, the
user needs to press the button or
send an ON command over the
Z-Wave link. The limit for each
country plug type is shown below:
UK: 13.5A
EU: 16.5A
ANZ: 10.5A 11

Metering
The SSP 302 is a metering device
that provides the following
electrical parameters with an
accuracy of ±2%, or better, from
23W to full load, and less than
0.5W from 1W to 23W:
1. Voltage
2. Current
3. Active power
4. Apparent Power
5. Active Energy
6. Apparent Energy
7. Power Factor

Energy Save Mode
If the current is less than the
standby current for 30 seconds, the
load will be disconnected to save
energy (refer to the configuration
parameter 16 of Configuration
parameters table for how to
configure standby current).
13

Button Actions
Press time Operation
LED
status
Less than 1
second Toggles supply to socket outlet
Toggles
green
LED
1-4 seconds
Association
NA
4-7 seconds Inclusion/
exclusion
Red LED
flashes
twice per
second
7-11
Seconds
Resets device data NA
11-15
seconds
SSP 302 resets to
factory default
(only
available for up to
60 seconds from
power up
Red LED
flashes
once per
second

Z-Wave Plus command
classes
Z-Wave Plus
Device
Classes
Implemented Device
Class
Generic
Binary Switch
Specific
Not used
Basic
Routing Slave
Supported Command class
Command Class
Commands
Supported
Basic CC (V1)
Get
Set
Report
Basic CC is mapped to binary switch CC
Binary switch (V1)
Get
Set
Report
Manufacturer
Specific (V2)
Get
Report
15

Manufacturer ID =
0x0059
Product Type ID =
0x0011
Product ID = 0x0001
(UK & EU)
Product ID = 0x0002
(ANZ)
Version (V2)
Get
Report
Version Command
Class Get
Version Command
Class Report
Association (V2)
Set
Get
Report
Remove
Supported Groupings
Get
Supported Groupings
Report
Specific Group Get
Command
Specific Group Report

Command
Product supports five association groups and
group 1 to 4 are having maximum of 4 nodes
and group 5 is having one association node.
Configuration (V1)
Set
Get
Report
See Configuration Parameters for details
Device Locally
Reset (V1)
Report
Power cycle the device and press and hold the
button for more than 11 seconds and less than
15 seconds within the 60 seconds of power
cycle to put the device in factory default, that
include setting all the configuration, Association
to factory default and removing the device from
Z-Wave network.
Association Group
Info (V1)
Group Name Get
Group Name Report
Group Info get
Group Info Report
Group Command List
Get
Group Command List
17

Report
Association group Name:
Group1 : Lifeline
Group2: Power
Group3: Electrical Parameter
Group4: Relay Status
Group5: Time
Profile MSB:
ASSOCIATION_GROUP_INFO_REPORT_P
ROFILE_GENERAL
Profile LSB:
Group1: 0x01
Group2: 0x02
Group3: 0x03
Group4: 0x04
Group5: 0x05
Supported Command class and command :
Group 1: to Group3:
CC: COMMAND_CLASS_METER_V3
Command: METER_REPORT
Group4:
CC:
COMMAND_CLASS_SWITCH_BINARY
Command : SWITCH_BINARY_REPORT
Group5:
CC: COMMAND_CLASS_TIME

Command: TIME_GET, DATE_GET
Z-Wave Plus Info
(V2)
Get
Report
Role Type:
ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_
ALWAYS_ON
Node Type:
ZWAVEPLUS_INFO_REPORT_NODE_TYPE_ZWAVE
PLUS_NODE
Installer Icon:
ICON_TYPE_GENERIC_ON_OFF_POWER_SWITCH
User Icon-
ICON_TYPE_GENERIC_ON_OFF_POWER_SWITCH
Power Level
(V1)
Power Level Set
Power Level Get
Power Level Report
Power Level Test Node
Set
Power Level Test Node
Get
Power Level Test Node
Report
19

Meter (V3)
Get
Report
Supported Get
Supported Report
Meter Reset
Meter table
Monitor (V1)
ID Get
ID Report
Capability Get
Capability Report
Current Data Get
Current Data Report
Meter Table
Configuration
(V1)
Meter Table Point Adm
Number Set Command
CRC-16
Encapsulation
(V1)
CRC-16 Encapsulated
Command