secureView SV- 6912.IR User manual
INSTALLATION INSTRUCTIONS:
The SV-6912.IR is a hanging style Rear View Camera with Night Vision. It can be mounted up
high on the back of the vehicle which makes it perfect for bigger vehicles such as Semi Trucks,
Motor Homes, Trailers, and Vans. It can also be mounted down low on the vehicle, either on
the bumper or under a license plate bezel if there is adequate space.
FEATURES:
•Hanging style CCD color camera
•120° Viewing Angle
•Equipped with Infra Red LED for Night Vision
•Can be mounted high or low on the vehicle depending on owner’s preference
•Optional Audio Input. Perfect for hooking up to a DVR system
•Perfect for Semi Trucks, Motor Homes, Buses, or Vans
•Parking assist lines to help driver accurately judge distance behind the vehicle
•Durable Zinc Alloy Die Cast Body
•Reverse Image only
•Provides extra security when backing-up
•Works perfectly with any SecurView™ or aftermarket monitor
•Waterproof Camera Design (IP68)
SV- 6912.IR
Hanging Style Rear View
Camera with Night
Vision
INSTALLATION
INSTALLATION PRECAUTIONS:
1. The Securview™ SV-6912.IR is designed to be mounted up high on the vehicle. Make sure
there will be adequate space to mount the camera.
2. Make sure to double check that the camera will not be blocking any brake lights or turn
signals on the vehicle.
3. Make sure that there is adequate space behind the mounting location so that a hole can be
drilled for routing the camera wire harness into the vehicle.
MOUNTING:
1. Locate a suitable place to mount the camera.
2. Remove the assembly screws from the SV-6912. This will allow the camera and mounting
bracket to be separated.
3. Once you have the Mounting Bracket in a suitable location, Screw it down to the mounting
surface you have chosen. (Make sure to double check behind your drilling location for
clearance)
4. Locate a suitable place to drill a hole to route the camera wiring harness into the vehicle.
5. Route the harness through the hole. Seal the hole the rubber grommet provided on the
camera wiring harness. Squeeze the grommet tightly into the hole so that no water can leak
through.
6. Reassemble the Camera to the Mounting Bracket.
SIDE
VIEW
Mounting
Surface
Mounting
Screw
Rubber Grommet
Cable
SV-6912 Camera
Mounting Bracket
Camera
Mounting
Screw Mounting
Screw
Assembly
Screw
Assembly
Screw
CAMERA:
1. This color CCD camera is maintenance-free, waterproof (IP-68) and vibration resistant.
2. This camera is completely electronic. There are NO manual adjustments for focus, etc.
3. This camera is equipped with Night Vision to give you better lighting at night time. This plus
the vehicle’s reverse light and the ambient lighting in the area should make it perfect for night
time driving.
WIRING:
1. Carefully choose a hidden out-of-sight location for drilling the cable hole. Some vehicles may
have an existing hidden rubber grommet or plug available to avoid having to drill into the
body. Be sure to double-check for any wiring or obstructions behind the surface where you
are going to drill the cable hole. Use the rubber grommet to make a watertight seal for the
cable where it passes into the vehicle.
2. Choose a convenient place to run the camera cable up the left, right or center of the vehicle.
As a rule of thumb, try to avoid main factory harness looms that may contain high levels or RF
noise or interference.
3. You can connect the camera power at the rear of the vehicle behind the reverse lights. You
may also connect power inside the vehicle under the dash or in the trunk. The Red power
wire goes to Reverse Light +12V, and the Black wire to Ground.
4. Run the Yellow RCA video cable to your monitor’s video input or reverse camera input. The
White RCA cable is for audio and can be hooked up to the audio source of your monitor (If
Equipped)
5. The small white plug is for the parking assist lines. Clip on the plastic jumper cap to engage
the parking assist lines or leave it disconnected to turn them off.
Rubber Grommet
Yellow Video RCA
Power
Connector
Black
Red
+12V Reverse
Light wire
Ground
White Audio RCA
Parking Assist
Lines Jumper
MONITOR
SV-6912 CAMERA
DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the SV-6912.IR be held liable for
consequential or incidental damages sustained in connection with the use of the SV-6912.IR Rear Vision
System. The SV-6912.IR is designed as a safety enhancement device and is in no way intended as a
replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. It is the sole responsibility of the vehicle owner to check and verify any and all
State or Federal Motor vehicle codes with regards to modifications of the vehicle.
www.crimestopper.com
email@crimestopper.com
Phone (800) 998-6880
FAX (805) 581-9500
© 2013 Crimestopper Security Products
REV.C
5-2-2013
SPECIFICATIONS:
1/4 Color CMOS Sensor Video Output: 1.0 V P-P composite (75 Ohm load)
Dimension (In.): 2¼"(L) × 2⅛"(W) × 2⅛"(D) Supply Voltage: +12VDC
Power Consumption: 200mA with Night Vision
Weight: 20 Oz. Electronic Shutter: 1/50(1/60) s – 1/100000s
Pixels: NTSC: 648 (H) × 492 (V) White Balance: Automatic
PAL: 648 (H) × 492 (V) Gamma Correction: 0.45
Resolution: > 300,000 pixels S/N Ratio: More than 48dB
More than 420 TV lines Operating Temp: -4° to 158° F (-20° to 70° C)
Minimum Illumination: 0.3 LUX (day) 0 LUX / F 2.0 (night) Gain Control: Automatic
Lens Type: Normal
Horizontal Angle: 130°
Vertical Angle: 90°
Table of contents
Other secureView Dashcam manuals
