Security Brands Edge E2 User manual

1 of 16
QUICK START GUIDE
Model 27-220 (HID, SK)
1 2
WARNING

CAUTION

3
Unpack box and make sure you have all items shown here.
(Screwdriver not shown.)
Unlock and open front panel of unit for
mounting, wiring, and setup.
AUTOMATIC GATES CAN CAUSE SERIOUS
INJURY OR DEATH!
ALWAYS CHECK THAT THE GATE PATH IS
CLEAR BEFORE OPERATING!
REVERSING OR OTHER SAFETY DEVICES
SHOULD ALWAYS BE USED!
Edge Unit
(HID version shown)
Programming Pad
(35-030)
Key
Carriage Bolt
( 4x )
Hex Nut
( 4x )
12-V AC/DC Adapter
(PS-12DC1)
Mount unit to pedestal using included
mounting hardware.
(This step may be completed later.)
Continued on next page...
Use all four carriage bolts when mounting
the unit to a pedestal.
Leave the antenna in place.
Seal all openings created in the enclosure.
Failure to follow these instructions can
damage the unit and/or cause it not to
function correctly!

© 2021 Security Brands, Inc. All rights reserved.
2 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
What’s what?
All important components labeled
Unit shown with front panel open.
Wiring/cabling not shown for clarity.
Wiegand Terminals
For wiring to Wiegand devices
See Page 6
Reset Button
For performing unit reset
Keypad Connector
For plugging in Programming Pad
when programming at Edge unit
Power, Relay, Event Terminals
For wiring to power, wiring to
gate operator or door opener, and
connecting request-to-exit devices
See Pages 3 and 5
Programming Pad
(35-030)
For programming. See Pages 8–15.
(We recommend unplugging from
circuit board and storing against
right-side wall inside Edge enclosure
when not in use.)
Relay Status LEDs
Relay is active when lit
Digital Input Terminals
For connecting various accessories
See Page 5

3 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
4CAUTION

If the included 12-V AC/DC adapter will not be
used, please go to Page 4 and follow the
procedure, Using a Third-Party Power Source.
Do not exceed 24 VAC/DC! Failure to choose a
compatible power source can damage the unit!
Connect wires.
Feed wires through back of unit,
and connect as shown using
included screwdriver.
Excessive force can damage unit!
RELAY A
J10
RELAY B
J11
12–24 VAC/DC
POWER
J3 J17 J5
EVENT INPUTS
Edge Power, Relay, Event Terminals Gate Operator / Door Opener
POWER (+)
POWER (–)
COM
RADIO
COM
REVERSE LOOP
STOP
CLOSE
The GROUND terminal is optional
unless required by local code(s).
If using, please connect to earth
ground or equivalent. 12-V AC/DC Adapter
(Model PS-12DC1 included)
Relay B can be wired to a second device in the same manner.
FREE EXIT
COM
N/C N/C
COM
N/O
GND
EVNT2
GND
EVNT1
Consult gate/door opener
manual for exact connections.
Terminals vary widely across
manufacturers and models.
If plugging into duplex outlet,
remove screw from outlet plate,
and secure with included screw.
Additional wiring diagrams can
be found on Pages 5 and 6.
+–
Third-Party 12–24-VAC/DC
Power Source
POS. (+)
NEG. (–)
OR
COM
N/O
COM
OPEN

© 2021 Security Brands, Inc. All rights reserved.
4 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
4a
4b
IMPORTANT
rr
CAUTION

STOP

6
7
5
If you would like to use a third-party
power source such as solar, verify that it
conforms to the following specs:
Connect wires to unit as shown in
Step 4.
Connect wires to your power source,
making sure you connect positive to
positive and negative to negative.
Double check that you have wired from
positive on the Edge unit to positive on your
power source and negative on the Edge unit
to negative on your power source.
Reverse polarity can damage the unit!
Input 12–24 VAC/DC
no more than 10% beyond this range
Current Draw less than 111 mA @ 12 VDC
less than 60 mA @ 24 VDC
Using a Third-Party
Power Source (Optional) Before going forward, double check all
wiring and make sure the unit has power!
Wiring diagrams for connecting to accessory
devices can be found on Pages 5 and 6.
For connecting accessories not mentioned,
please contact Technical Support.
Make sure the gate or door path is clear
before completing Step 7!
Add Access Code to Relay A.
(To add multiple codes, enter each of them before pressing pound key.)
Make sure gate or door path is clear;
then enter access code on Pad, and
confirm gate or door opens.
Jump to Page 7 to continue programming and
download the Edge Smart Keypad app.
INSTALLATION COMPLETE!
N
11 12 5 ? ? ? ?
Access Code to Be Added
(4 digits by default; numbers only)
Master Code
(can be changed)
Sub Mode
Grab Programming Pad, making sure it
is connected to circuit board.
NOTE: The green arrow indicates a “good” tone on the Edge unit. By default, the following
codes are reserved and cannot be used: 1251, 1273, 1366, 1381, 1387, 1678, 1752, and 1985.

5 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
BA
J8J9
Edge Digital Input Terminals
#2
GND
#1
GND
Digital Inputs
Wiring to various accessories
DIGITAL INPUTS
Request-to-Exit Device
(58-RTE-P is shown)
Door Switch
Event Inputs
Wiring for accessories such as a request-to-exit device
RELAY A
J10
RELAY B
J11
12–24 VAC/DC
POWER
J3 J9 J5
EVENT INPUTS
Edge Power, Relay, Event Terminals
N/C N/C
COM
N/O
GND
EVNT2
POS. (+)
NEG. (–)
COM
N/O
GND
EVNT1
Alarm Contact
To Alarm
System
Event Input configuration
instructions can be found
on Pages 10 and 11.
Digital Inputs can be
configured using the
Edge Smart Keypad app.

© 2021 Security Brands, Inc. All rights reserved.
6 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
CCAUTION

J6 J7 J4 J5
Edge Wiegand Terminals
UNAVAILABLE
WIEGAND-1
DOOR/READER
WIEGAND-2
Wiegand Device
WIEGAND OUTPUTS
+12V
GND
LED 1 LED 2
DATA 0 DATA 1
Disconnect power to the Edge unit
before connecting Wiegand devices.
Failure to disconnect power can
damage the unit!
Wiegand Device
Wiring for a Wiegand device
Wiegand programming
instructions can be found
starting on Page 12.
GND
LED2 LED1
DAT0 DAT1
+12V
Wiegand 1 Terminals
Connected to Onboard
Proximity Card Reader

7 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
a
b
c
D
NEED HELP

Grab your smartphone or tablet.
(These steps are optional. Unit can be
fully programmed from keypad.)
Navigate to your app store, and search
for “edge smart keypad.”
Find the Edge Smart Keypad app by
Security Brands, Inc. and download it.
Edge Smart Keypad
Security Brands, Inc.
Downloading the Edge Smart
Keypad App for iOS/Android Pairing Edge Unit
Connecting your mobile device to your Edge unit for use with app.
The app is available for administrators who want to use it. Nearly all
programming functionality is available via the Programming Pad.
r
The Edge Smart Keypad app is for
ADMINISTRATOR USE ONLY and is
not intended for users.
You can find plenty of useful resources online
to help you get your new Edge unit up and
running quickly and easily.
Go to securitybrandsinc.com/edge/
If you need further assistance, please call
Technical Support at [phone].
For more information and guidance, please go to securitybrandsinc.com/edge/ or call
Technical Support at [phone] for assistance.
IMPORTANT! Make sure your Edge unit is powered on and that Bluetooth is enabled on
your mobile device or pairing will not work.
Step 1 - Grab your mobile device and open the Edge Smart Keypad app.
If you do not have the app, follow the steps on this page for downloading it.
Step 2 - Fill out your account information and tap the “Sign Up” button.
If you have already created an account, you will log in instead.
Step 3 - On the Paired Keypads screen, tap the “Add Keypad” button.
Step 4 - On the Add Keypad screen, tap the Edge unit you want to pair.
If you do not see any Edge units listed, make sure your Edge unit is powered on and is in
Bluetooth range.
Step 5 - Complete the procedure shown on your mobile device.
These steps will be completed using the PIN pad on your Edge unit.
Step 6 - Enter the Master Code (default is 1251) on your mobile device.
Step 7 - Enter the code shown on your mobile device at the Edge unit.
This step must be completed within the time duration displayed.
Step 8 - Change your Master Code if you like.
This step is recommended, but optional, and can be done at a later time.
Your new Edge unit is now be paired and will appear on the Paired Keypads screen. Tapping on the
Edge unit on this screen will give you access to relay control and full access control management of
the Edge unit from within the app.

© 2021 Security Brands, Inc. All rights reserved.
Model 27-220 (HID, SK)
8 of 16
QSG-27220-EN Rev. B (2/2021)
QUICK START GUIDE
E1 Direct Programming / Unit Configuration
The Star Key (*)
If a mistake is made, pressing the star key
deletes your entry. Two beeps will sound.
The Pound Key (#)
The pound key is good for one thing and one
thing only: exiting programming mode.
Things to Know
Sub Mode
3 1 12 5 ? ? ? ?
New Master Code
(4 digits; numbers only)
Current Master Code
(1251 is default)
Sub
Mode A
Sub
Mode B
441 12 5 ? ? ? ?
Sleep Code
(4 digits; numbers only)
Master Code
(1251 is default)
Change Sleep Code
Change Master Code
(Highly recommended for security purposes)
Programming Sub Modes
1 Add Access Code(s) to Relay A
2 Delete Code (Non-Wiegand)
3 Change Master Code
4 - 3 Add Latch Code to Relay B
4 - 4 Change Sleep Code
4 - 5 Change Code Length (Non-Wiegand)
4 - 6 Change Relay Trigger Time
4 - 7 Enable/Disable Timers and Schedules
4 - 8 Enable/Disable “3 Strikes, You’re Out”
4 - 9 Configure Event Input 1
5 Add Latch Code to Relay A
6 Configure Wiegand Inputs
7 Add Access Code(s) to Relay B
8 Add Limited-Use Code
0 Delete All Codes and Timers
Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
By default, these codes are unavailable for use:
1251, 1273, 1366, 1381, 1387, 1678, 1752, 1985.
FIND MORE

For all programming not shown here,
as well as reset procedures and the Edge
Smart Keypad app user guide, please visit
our Edge start page:
securitybrandsinc.com/edge/

9 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
E2 Direct Programming / Unit Configuration Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
Current State
(On: 1 beep;
Off: 2 beeps)
1 12 5
Master Code
(1251 is default)
Sub
Mode A
Sub
Mode B
84 #
Configure
(1 for no change;
2 to change state)
?
Enable/Disable “3 Strikes, You’re Out”
(When enabled, the unit will sound an alarm and go into a 90-second lockdown for 90 seconds when an incorrect code is entered three times.
Change Relay Trigger Time
Sub
Mode A
Sub
Mode B
641 12 5 ? ?
Master Code
(1251 is default)
? ? ?
Trigger Time in Seconds
(001–999)
Relay
(1 for A; 2 for B)
Configure Wiegand Input
(Allows enabling or disabling of a Wiegand input and configuration of the Wiegand device type. For the tag reader type, use the Edge Smart Keypad app.)
Sub
Mode A
Wiegand Input
(1 for 1; 2 for 2)
? 61
Configuration
(0 for disabled; 1 for keypad;
2 for card reader; 3 for remote)
? # 1 2 5
Master Code
(1251 is default)
05 0
Sub Mode B
Sub
Mode A
6 1 12 5 1
Master Code
(1251 is default)
Change Default Facility Code
60
Sub Mode B
?? ?
Facility Code
(000–255)

© 2021 Security Brands, Inc. All rights reserved.
10 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
E3 Direct Programming / Unit Configuration Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
Current State
(Unit beeps mode
number or good tone
when disabled)
1 12 5
Master Code
(1251 is default)
Sub
Mode A
Sub
Mode B
94
Event Mode
(1, 3, 4)
?#
?
Relay
(1 for A; 2 for B)
Modes 1, 3, and 4
Configure Event Input 1
(Allows an external device to affect keypad operation or trigger a relay. To configure additional inputs, use the Edge Smart Keypad app.)
Mode 1 - Remote Open Mode
Triggers either Relay A or Relay B when event input state changes
from normally open (N/O) to normally closed (N/C).
Mode 2 - Log Mode
Makes log entry of event input state when event input state changes
from normally open (N/O) to normally closed (N/C).
Mode 3 - Remote Open and Log Mode
Combines Modes 1 and 2.
Mode 4 - Arming Circuit Mode
Enables either Relay A or Relay B when event input state changes from
normally open (N/O) to normally closed (N/C). Otherwise, selected relay
is disabled.
Mode 5 - Remote Operation Mode
Triggers or latches either Relay A or Relay B when event input state
changes from normally closed (N/C) to normally open (N/O).
Mode 0 - Event Input 1 Disabled
Sub
Mode A
6 1 12 5 3 ?
Master Code
(1251 is default)
Toggle Silent Mode
(Toggles Silent Mode, which mutes all audible-tone feedback on unit)
90
Sub Mode B
? ? ?
Master Code Again
(1251 is default)

11 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
E4
Current State
(Unit beeps mode
number or good tone
when disabled)
1 12 5
Master Code
(1251 is default)
Sub
Mode A
Sub
Mode B
94
Event Mode
5
?
Setting
(1 for Relay; 2 for
Relay Operation)
#
?
Relay
(0 for A; 1 for B)
#
?
Relay Operation
(0 for trigger; 1 for latch)
Current State
(Unit beeps mode
number or good tone
when disabled)
1 12 5
Master Code
(1251 is default)
Sub
Mode A
Sub
Mode B
94 #
Event Mode
0
Current State
(Unit beeps mode
number or good tone
when disabled)
1 12 5
Master Code
(1251 is default)
Sub
Mode A
Sub
Mode B
94 #
Event Mode
2
Mode 5
Mode 2
Disable Event/Digital Inputs (Mode 0)
Configure Event Input 1 (continued)
(Allows an external device to affect keypad operation or trigger a relay. To configure additional inputs, use the Edge Smart Keypad app.)
Direct Programming / Unit Configuration Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.

© 2021 Security Brands, Inc. All rights reserved.
12 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
F1 Direct Programming / Wiegand Card Reader Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
? ? ?
Sub
Mode A
Wiegand Input
(1 for 1; 2 for 2;
skip for both)
?61
Sub
Mode B
2
?
1 2 5
? ? ? ?
Code(s) to Be Added
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
Add Wiegand Card/Remote/Vehicle Tag Access Code(s)
(To add multiple codes, enter each of them before pressing pound key)
Facility Code
?? ?
Relay
(100 for A; 104 for B)
? ? ? ?? ?
Sub
Mode A
?61
Sub
Mode B
3
?
1 2 5
? ? ? ?
Starting Code
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
?????
Ending Code
(5 digits; 00000 to 65535)
Bulk Add Wiegand Card/Remote/Vehicle Tag Access Code(s)
Relay
(100 for A; 104 for B)
Facility CodeWiegand Input
(1 for 1; 2 for 2;
skip for both)

13 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
F2 Direct Programming / Wiegand Card Reader Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
? ? ?
Sub
Mode A
Wiegand Input
(1 for 1; 2 for 2;
skip for both)
?61
Sub
Mode B
2
?
1 2 5
? ? ? ?
Code(s) to Be Added
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
Add Wiegand Card/Remote/Vehicle Tag Latch Code(s)
(To add multiple codes, enter each of them before pressing pound key)
Facility Code
?? ?
Relay
(103 for A; 105 for B)
? ? ? ?? ?
Sub
Mode A
?61
Sub
Mode B
3
?
1 2 5
? ? ? ?
Starting Code
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
?????
Ending Code
(5 digits; 00000 to 65535)
Bulk Add Wiegand Card/Remote/Vehicle Tag Latch Code(s)
Relay
(103 for A; 105 for B)
Facility CodeWiegand Input
(1 for 1; 2 for 2;
skip for both)

© 2021 Security Brands, Inc. All rights reserved.
14 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
F3 Direct Programming / Wiegand Card Reader Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
? ? ?
Sub
Mode A
Wiegand Input
(1 for 1; 2 for 2;
skip for both)
?61
Sub
Mode C
2
?
1 2 5
? ? ? ?
Code(s) to Be Added
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
Add Wiegand Card/Remote/Vehicle Tag Manager Access Code(s)
(To add multiple codes, enter each of them before pressing pound key)
Facility Code
11 0
Sub
Mode B
? ? ? 11 0
Sub
Mode A
?61
Sub
Mode C
3
?
1 2 5
? ? ? ?
Starting Code
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
?????
Ending Code
(5 digits; 00000 to 65535)
Bulk Add Wiegand Card/Remote/Vehicle Tag Manager Access Code(s)
Sub
Mode B
Facility CodeWiegand Input
(1 for 1; 2 for 2;
skip for both)

15 of 16
Model 27-220 (HID, SK)
QUICK START GUIDE
F4 Direct Programming / Wiegand Card Reader Green arrow indicates “good” tone on unit.
Always wait for good tone before moving on.
? ? ?
Sub
Mode A
Wiegand Input
(1 for 1; 2 for 2;
skip for both)
?61
Sub
Mode C
2
?
1 2 5
? ? ? ?
Code(s) to Be Deleted
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
Delete Wiegand Card/Remote/Vehicle Tag Manager Code(s)
(To add multiple codes, enter each of them before pressing pound key)
Facility Code
02 0
Sub
Mode B
? ? ? 02 0
Sub
Mode A
?61
Sub
Mode C
3
?
1 2 5
? ? ? ?
Starting Code
(5 digits; 00000 to 65535)
Master Code
(1251 is default)
?????
Ending Code
(5 digits; 00000 to 65535)
Bulk Delete Wiegand Card/Remote/Vehicle Tag Code(s)
Sub
Mode B
Facility CodeWiegand Input
(1 for 1; 2 for 2;
skip for both)

© 2021 Security Brands, Inc. All rights reserved.
16 of 16
QSG-27220-EN Rev. B (2/2021)
Model 27-220 (HID, SK)
QUICK START GUIDE
Call [phone]
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
Edge E2
27-220HID
Notes