Security Brands ADVANTAGE DKLP Economy 19-100E User manual

QUICK START GUIDE ADVANTAGE DKLP Economy
1 of 4
Model 19-100E
2Make sure you have everything shown here. 3Unlock and remove front panel
of keypad unit; then using
carriage bolts and hex nuts,
attach unit to pedestal as shown.
4For ease of wiring, insert front
panel into enclosure as shown.
START HERE
Keypad Unit Key Carriage Bolt
( 4x )
Hex Nut
( 4x )
Reset Button
For performing reset procedures
Power and Relay Terminals
For wiring to gate operator or
door opener and power
POWER MUST BE 7–14 VDC!
CAUTION!

Double check your wires! You must wire from
positive on keypad unit to positive on your
power source and negative on keypad unit to
negative on your power source.
Reverse polarity can damage keypad unit!
What’s what?
Important components labeled
Keypad Unit Front Panel
Shown as it would appear with front panel inserted
into enclosure as in Step 4.
WARNING!
AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
ALWAYS CHECK that the GATE PATH IS
CLEAR BEFORE OPERATING!
REVERSING or other SAFETY DEVICES
SHOULD ALWAYS BE USED!

1Carefully unpack box.

QSG-19100E-EN Rev. C (9/2021)
© 2021 Security Brands, Inc. All rights reserved.
QUICK START GUIDE ADVANTAGE DKLP Economy Model 19-100E
7–14 VDC ONLY
POWER
7–14 VDC ONLY
POWER RELAY
Gate Operator / Door Opener
Advantage DKLP
Power and Relay Terminals
5a Make the connections
Wiring for Gate Operator or Door Opener
POS. (+)
NEG. (–)
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
FREE EXIT
COM COM
RADIO
COM
POS. (+)
NEG. (–)
N/C
N/O
Advantage DKLP
5b Make the connections
Wiring for Electric Door Strike
Power Source
(7–14 VDC ONLY)
Electric Strike
Advantage DKLP
5c Make the connections
Wiring for Mag Lock
Mag Lock
(57-1200MAG is shown)
Power Source
(7–14 VDC ONLY)
Earth ground is
optional unless
required by
local code. This wire is not
part of the unit’s
wire harness and
must be supplied.
This wire is not
part of the unit’s
wire harness and
must be supplied.
+–
+–
Earth ground is
optional unless
required by
local code.

QUICK START GUIDE ADVANTAGE DKLP Economy
3 of 4
Model 19-100E
A1 Additional Programming
6Add Access Code(s).
(To add multiple codes, enter each of them before pressing pound key)
11 12 5 _ _ _ _
Access Code(s)
(4 digits; numbers only)
Master Code
(1251 is default)
Sub Mode
Sub Mode
Sub Mode
Sub Mode
21 12 5 _ _ _ _
Code(s) to Be Deleted
(4 digits; numbers only)
Master Code
(1251 is default)
51 12 5 _ _ _ _
Latch Code
(4 digits; numbers only)
Master Code
(1251 is default)
Set Latch Code
Your system is ready to use.
INSTALLATION COMPLETE!
N
Programming Sub Modes
1Add Access Code(s)
0Delete All Codes
2Delete Code(s)
3Change Master Code
5Set Latch Code
4Set Relay Output Time
NOTE: The Master Code is for programming only and will not trigger the relay. The green
arrow indicates a “good” tone on the keypad. An incorrect entry will sound a “bad” tone.
Delete Code(s)
(To delete multiple codes, enter each of them before pressing pound key)
31 12 5 _ _ _ _
New Master Code
(4 digits; numbers only)
Current Master Code
(1251 is default)
Change Master Code
NOTE: Green arrow indicates “good” tone on keypad.
Always wait for good tone before moving on.
The Star Key (*)
The star key deletes your current entry.
If you happen to make a mistake keying in a
code, simply press the star key to delete the
entire entry and start over.
The Pound Key (#)
The pound key is good for one thing and
one thing only: exiting Programming Mode.
Whenever you’re in Programming Mode,
simply press the pound key to get out.
Master Reset Procedure
If for some reason the Master Code and/or
Latch Code is forgotten, a reset procedure is
available to remedy the situation.
This procedure can be found on Page 4 of
this guide.
Things to Know
7Make sure gate path is clear; then
enter access code on keypad and
confirm gate opens.

QUICK START GUIDE ADVANTAGE DKLP Economy
4 of 4
Model 19-100E
QSG-19100E-EN Rev. C (9/2021)
© 2021 Security Brands, Inc. All rights reserved.
NEED HELP Call [phone]
Email [email protected]
We are available Mon–Fri / 8am–5pm Central
A2 Additional Programming (continued) BMaster Reset Procedure
Sub Mode
Sub Mode
01 12 5 1 2 5 1
Master Code AgainMaster Code
(1251 is default)
Keypad will sound
“good” tone when
complete.
Delete All Codes (Cannot Be Undone)
41 12 5 _
Seconds
(0–9)
Master Code
(1251 is default)
Set Relay Output Time
NOTE: Green arrow indicates “good” tone on keypad.
Always wait for good tone before moving on.
This procedure is used if the Master Code is unknown, or if the Latch Code is unknown and
the unit is in Latch Mode. All other codes will be retained after completing this procedure.
NOTE: If an error is made during these procedures, an “error” tone will sound, and you
must start again from the beginning.
Step 1 - Open front panel on unit.
Step 2 - Disconnect power.
Remove one power wire from screw terminal on circuit board by unscrewing and removing.
Step 3 - Press and hold Reset Button; reconnect power; then release Reset Button.
Insert removed power wire back into screw terminal and screw down to secure. Unit will
sound one (1) tone. Release Reset Button after you hear tone.
Step 4 - Close front panel on unit.
The Master Code is now reset to default (1251).