Security Brands 14-R433 User manual

INSTRUCTIONS RIDGE REMOTE (433 MHZ)
Model 14-R433
1 of 2
IN THE BOX
Make sure you have everything shown here.
This remote must be paired to and used
with a Security Brands Ridge 2.0 Transceiver
(Model 14-REC20) to work correctly.
Ridge Remote Visor Clip
Button 1
LED
PROG LED
PROGRAMMING PAIR
Button
Button 2
WHAT’S WHAT
The Ridge Remote has two programmable buttons and
a status LED. Each button can be paired to a separate
modes of operation.
BASIC SETUP
1. On Ridge 2.0 Transceiver, hold down
PROGRAMMING PAIR button for three seconds
and release. PROG LED will light up.
NOTE:The transceiver must be powered up and
have its cover removed for this step. Please see the
instructions that came with it for help.
2. On Ridge Remote, press and hold down both
buttons and pay attention to remote LED.

call
[phone]
or email
[e-mail]
NEED
HELP
Two-Year Limited Warranty
Visit securitybrandsinc.com/warranty/ for details
2 of 2© 2021 Security Brands, Inc. All rights reserved. I-14R433-EN Rev. B (10/2021)
WARNING! AUTOMATIC GATES CAN CAUSE
SERIOUS INJURY OR DEATH!
ALWAYS CHECK THAT THE GATE PATH IS
CLEAR BEFORE OPERATING!
REVERSING OR OTHER SAFETY DEVICES
SHOULD ALWAYS BE USED!
3.
you want to program and release other button.
4.
now programmed.
5. Repeat procedure for second button if desired.
NOTE:The second button can be paired with the
MODE SELECTION
(MOMENTARY/LATCH)
1. On Ridge Remote, press and hold down both
buttons and pay attention to remote LED.
2. both
buttons.
3.
button you want to change modes on until LED
NOTE:If the relay on the Ridge 2.0 Transceiver is
already latched (on), it cannot be unlatched unless
the remote button is set to latch mode.
NOTE:If needed, follow the same procedure for the
second button.
HOW TO USE
1. Make sure you are in range of Ridge 2.0
Transceiver you want to control.
2. Press remote button paired to transceiver long
3. Transceiver will respond and operate gate/door.
NOTE:If the transceiver does not respond, make sure
If it is not, check the battery. If it still does not
respond, complete the pairing procedure again.
Go to securitybrandsinc.com/ridge/ for
more helpful resources.
Step 3 Step 4
INSTRUCTIONS RIDGE REMOTE (433 MHZ)
Model 14-R433

FCC Statement:
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
ISED RF exposure statement:
RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in
portable exposure condition without restriction.
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. The device has been evaluated to meet general RF exposure requirement.
Le matériel est conforme aux limites de dose d'exposition aux rayonnements énoncés pour fac un autre
environnement. ce dispositif a été évalué à satisfaire l'exigence générale de l'exposition aux rf.