SEI FA584800TX User manual

FA584800TX
Vine Wall-Mount Fireplace
Assembly Instruction
For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]
www.seidal.com
© Southern Enterprises Inc. All Right Reserved
.

Tool List: 3/16" drill bit, drill, tape measure and pencil .
FA584800TX
Vine Wall-Mount Fireplace
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage. Before beginning assembly,
separate each type of screw. Carefully study the screw diagrams below.
Suggested tools: Phillip head screw driver, power drill, 3/16” drill bit,
24”level, and a tape measure. Unit needs to be hung on wall stud for more
security and stability.
(1)
Fireplace assembly
1 PC
(2)Fuel
canister holder
3PCS
(3)Candle holder (4)Glass
1 PC 1 PC
(5) Adhesive pad (6)Plastic wall anchor
3PCS 3PCS
1 extra included
(7) Phillip head screw
3PCS
￠
￠￠
￠4mm ×1-3/4″
1 extra included
Care and Cleaning Instructions:
Before using , wipe with a clean , dry cloth.
Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
call Customer Service at 1-800-633-5096.
Do not return product to store. Please call
manufacturer for assistance, questions or
parts.
Assembly Tool Required
No.2 Phillips Screwdriver

FA584800TX
Vine Wall-Mount Fireplace
Assembly Instructions
DANGER
PLEASE USE IN WELLVENTILATED AREA
The fireplace will have open flames and will generate heat.
Make sure to keep all combustible items away from the fireplace when the gel fuel is
burning.
DO NOT touch the fireplace when the gel fuel is burning.
Not recommended for use on wall paper or wood paneled walls due to risk of
discoloration over time.
Please mount at least 1 screw
into a wall stud. Wall anchor is
not needed when screwing
directly into a wall stud.
1. Locate the fireplace on a solid
wall and at a comfortable height
off the floor, normally eye level.
2. Measure the wall and mark the
fireplace width and height. See
Figure 1.
Figure 1 – Installation Measurements
Eye Level
25 ″
18
-1/2″

Phillip head screw
Anchor
3. Measure the wall and mark the
location of the center of each of
the three screw mounting holes.
See Figure 2.
Using the level, make sure that all
three marks are level on the wall.
It’s highly recommended that
middle screw is inserted into a
wall stud.
4. Using the power drill and
3/16″drill bit, drill three 3/16”holes
through the wallboard at the
mounting hole marks.
NOTICE
Make sure not to drill into
electrical wiring or plumbing
pipes.
5. Insert one of the furnished
plastic anchors into each of the
three 3/16″holes. See Figure 3.
Make sure that the wall anchor is
flush with the wall.
NOTE : It may be necessary to
use a small hammer to gently tap
the anchor into place.
6. Using the phillip head
screwdriver, install one Phillip
Head Screw into each of the
anchors. See Figure 3. Turn the
screw in until there is a gap of
1/4″between the head of screw
and the wall surface.
Figure 2 – Screw Hole Location
Figure 3 – Wall Anchor Installation
15
-3/8"
8
"
Drill three
3/16
"
holes
into wall
1/4" Gap
3/16" Hole
8
"

7. Install the fireplace (1, Figure
4) onto the three mounting
screws using the mounting holes
(2, Figure 4). The proper and
secure mounting of the fireplace
is when the top edge of each of
the mounting holes is resting
securely on the mounting screw
(3, Figure 4).
NOTICE
Using the level, check to make
sure that the fireplace is
horizontally level and vertically
plumb (straight up and down).
8. Remove the three fuel canister
holders (2, Figure 5) from the
fireplace and install one gel fuel
canister (1, Figure 5) into each of
the holders.
NOTICE
Make sure to remove the gel fuel
canister paper label (4, Figure 5)
before installing the canister into the
holder.
Shake the gel fuel canister before
installing it into the canister holder.
9. Install the gel fuel holders into
the fireplace into the appropriate
mounting hole (3, Figure 5) in the
fireplace.
Figure 4 – Install Fireplace
Figure 5 –Fuel Canister Holder and Gel Fuel Canister
Gelfuel
4
1
2
3

Figure 7 – Fuel Canister Installed
Figure 6 – Fuel Canister Installed
10. Put adhesive pad (5) onto
glass panel as shown, then insert
glass into the holder as shown.
11. Following the instructions on
the gel fuel canister, remove the
lid (2, Figure 7) from the gel fuel
canister (1, Figure 7), and using a
long match, light the fuel in each
of the canister. Candle holder can
be used to extinguish fire.
2
1
3
3
21

PROLONGED USE OF THE GEL FUEL IN THE FIREPLACE WILL CAUSE THE FIREPLACE
TO BECOME HOTAND POTENTIALLY CAN CAUSE BURNS IFTOUCHED.
DO NOT BURN MORE THAN THREE CANISTERS OF FUELAT ONE TIME.
BEFORE LIGHTING THE FUEL, MAKE SURE THAT THE PAPER LABEL IS REMOVED
FROM EACH OF THE GEL FUEL CANISTERS.
USE LONG MATCHES TO LIGHT EACH CANISTER OF FUEL.
DO NOT TOUCH THE CANISTERS WITH BARE HANDS UNTILTHE FLAME HAS BEEN
EXTINGUISHED FOR 20 MINUTES.
DO NOT BURN ANYTHING EXCEPT THE SPECIFIED CANISTERS OF GEL FUEL IN THE
FIREBOX.
KEEPCHILDRENAWAY FROM THE FIREPLACE WHEN IN USE.
KEEP FLAMABLE OBJECTS, SUCH AS CURTAINS OR DRAPERYS, AWAY FROM THE
FIREPLACE WHEN THE GEL FUEL HAS BEEN IGNITED.
MAKE SURE THE CUSTOMER DOES NOT PLACE ANY DECORATIVE ITEMS ON TOPOF
THE UNITATANYTIME.
DO NOT TOUCH THE UPPER PART OFTHE UNIT WHILE IT IS STILL IN OPERATION.
THE CANDLE HOLDER ACTS AS A COVER TO PUT OUT FIRE IF ONE WISHES TO STOP
THE FLAME.
NEVER LEAVE BURNING GEL FUEL UNATTENDED.
CARE INSTRUCTION: WIPE DOWN UNITAND CANDLE HOLDER WITH SOFT DAMP
CLOTH.
WHEN USINGTHE CANDLE HOLDER PLEASE MAKE SURE THAT THE CANNISTER
HOLDERS ARE IN PLACE.
DANGER

We'd love to hear from you! Email us photos of our products in your home at [email protected] and we
might feature it on our site or use it to model one of our inspirational photos.
“PARTS WILL BE SENT IF AVAILABLE FROM SEI” “THIS IS NOT A WARRANTY”
Parts Replacement Form
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/ Website/ Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019
Please count, identify and compare parts and hardware list to be sure all parts are present. It may help to divide
parts and label them to correspond with part list. Extra hardware may be included. If any items are missing, please
contact Southern Enterprises at 800-633-5096 or in Dallas [phone]/ 9am – 4pm Mon-Fri Central time if you
have product issues with your purchase. Please ask for a customer service representative for issues involving
damages or replacement parts. Please ask for a technical assistance representative for any issues with product
assembly and product construction. Please contact the retailer that you purchased from for returns.
Missing or damaged hardware and/ or parts will be replaced free of charge. We do not sell parts. We do not
recommend modifying product(s) and we are not responsible for any damages due to product modification(s).
If this product has not been purchased from our retail affiliates (within 9 months), we are under no obligation to
provide parts or replacements merchandise. Parts will not be available for items arriving fully assembled.