SEI CARSHAW CM979000TX User manual

For assistance with assembly contact:
Southern Enterprises, Inc.
Customer Service 1-800-633-5096
[e-mail]
wwww.seidal.com
CM979000TX
4PC CONSOLE/MIRROR/
SCONCE PAIR SET - CARSHAW
Assembly Instructions

A1pc
Table-Top Frame
B 1pc
Scroll Pattern
C 1pc
Front Left Table Leg
D1pc
Front Right Table Leg
E1 1pc
Back Left Table Leg
E2 1pc
Back Right Table Leg
4PC CONSOLE/MIRROR/ SCONCE PAIR SET - CARSHAW
Parts List
Please review all parts and hardware before disposing of any packaging.
Call Customer Service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage. Before beginning assembly,
separate each type of screw. Carefully study the screw diagrams below.
You may receive extra hardware with your unit.

F1pc
Leg Stabilizer Bar
G1pc
Stabilizer Cap
H16pcs
Φ1/4"x 1/2"L Bolts
I1pc
Allen Wrench
J4pcs
Plastic Anchors
K4pcs
Mounting Screws
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or questions, please
Call Customer Service at 1-800-633-5096
Do not return product to store, please call
Manufacturer for assistance, questions or
Parts.

Figure 1 Console Table:
Place the table-top frame (A) upside down on
cloth covered work surface and attach the scroll
pattern (B) with two bolts (H) vertically above the
apron, as shown. Tighten these two bolts (H)
completely.
Figure 2 1. Locate the “C”, “D”, “E1”, “E2” sticker on
each leg (C, D, E1, E2) and table-top frame
(A) and make sure that they are positioned
exactly as shown.
2. Attach legs (C, D, E1, E2) to table-top frame
(A) using eight bolts (H). At this point, only
tighten the bolts halfway, using the Allen
wrench (I)
4PC CONSOLE/MIRROR/ SCONCE PAIR SET - CARSHAW
Assembly Instructions
B
A
H
H
H
H
E2 E1
D
C
H
C
E1
H
H
STICKER
“
E2”
“E1”
STICKER
STICKER
“C”
STICKER
“D”

Figure 3 Attach scroll pattern under the metal frame (A) to
front legs (C, D) using two bolts (H) and only
tighten halfway.
Figure 4 1. Attach leg stabilizer bar (F) to the four legs (C,
D, E1, E2) using four bolts (H).
2. Now fully tighten all bolts securely.
C
C
D
E1
E2
H
E1
C
E1
F
H
H
F
E2
D

Figure 5 1. Place table upright on the floor.
2. Screw stabilizer cap (G) into the leg stabilizer
bar (F). Tighten securely.
Figure 6 The table is completely assembled.
** We recommend that you save the Allen wrench
(I) and periodically tighten all bolts. Please
make sure all bolts are placed in their proper
positions and then are tightened securely to
ensure your safety.
** Weight restriction: 40 lbs.
** Do not sit, stand, or climb on table-top.
** Intended for indoor use only.
F
G

Mount the mirror and two wall sconces on the wall, as following steps.
1. The products should be mounted to studs in the wall if possible. If studs are not
available, the products should be mounted into drywall using the plastic anchors
and screws provided.
2. If mounting to studs, screw mounting screws directly into studs. Attach products
to the wall by placing the pre-installed hooks (see back of products) on to the screws.
Make sure screws are securely in place.
3. If mounting to drywall, drill 3/16" pilot holes into drywall. Insert plastic anchors
into pilot holes. Insert the screws provided into the plastic anchors. Attach products
to wall by placing the pre-installed hooks (see back of products) on to the screws.
Make sure screws are tightened securely in place.
CAUTION: PLASTIC WALL ANCHORS AND SCREWS MUST
BE USED WHEN MOUNTING PRODUCTS TO DRYWALL.
4PC CONSOLE/MIRROR/ SCONCE PAIR SET - CARSHAW
Installation Instructions
Hammer
(not provided)
Drill
(not provided)
Phillips screwdriver
(not provided)
Drill 3/16" pilot hole
Drywall
J
K
Wood Stud
Plastic wall anchors and
screws must be used when
mounting products to drywall.
K

Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at [email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019