SEI HE401100TX User manual

HE401100TX
Wall Mirror With Pegs
Assembly Instructions
For assistance with assembly contact;
Southern Enterprises, Inc.
Customer Service 1-800-633-5096
[e-mail]
www.seidal.com
MAXLOAD: 15LB.

HE401100TX
Wall Mirror With Pegs
Parts List
Please review all parts and hardware before disposing of any packaging.
Call customer service if missing hardware. Do not return to store/retailer.
Using a screw that is too long will cause damage.
Before beginning assembly, separate each type of screw. Carefully study
The screw diagrams below. You may receive extra hardware with your unit.
AQuantity
Of 1
TOP PANEL
B Quantity
Of 1
LEFT FACING PANEL
C Quantity
Of 1
RIGHT FACING PANEL
DQuantity
Of 1
MIRROR PANEL
E Quantity
Of 1
REAR PANEL
F Quantity
Of 1
CROSS-PANEL
G Quantity
Of 4
WOODEN PEGS
H Quantity
Of 4
11mmx1”
BOLTS
I Quantity
Of 1
ALLEN WRENCH
J Quantity
Of 17
CAM-BOLTS
K Quantity
Of 17
CAM-LOCKS
L Quantity
Of 1
CAM-TOOL
M Quantity
Of 2
8mmx1-1/2”
SCREWS
N Quantity
Of 2
ANCHOR
O Quantity
Of 6
COTTON MAT

Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth. Periodically
apply furniture wax to renew the finish. Avoid rubbing or
scratching the surface with rough or abrasive objects.
For replacement parts or questions, please call customer
service at 1-800-633-5096
Do not return product to store, please call
Manufacturer for assistance, questions or parts.
Assembly Tool Required
No.2 Phillips Screwdriver
Tool List:1/4”drill bit,drill,tape measure and pencil.
HE41100TX
Wall Mirror With Pegs
Assembly Instructions
ARROW (W)
(V) (U) ARROW
(J)
○
D
○
E
○
F
(K)
Figure 1
Step 1: Rotate the 3 cam-bolts (J) into
holes in cross-panel (F).
Step 2: Place the cam-bolts (J) into
holes in panel (D/E) and attach using
cam-locks (K).
○
B
○
D
(K)
○
C
(J)
FIGURE 2
Step 3: Rotate the 10 cam-bolts (J)
into holes in facing panel (B/C).
Step 4: Place the cam-bolts (J) into
holes in panel (D/E/F) and attach using
cam-locks (K).

(Z)
HOW TO USE THE ALLEN WRENCH
○
A
(K) (J)
(I)
(H)
○
G
FIGURE 3
Step 5: Rotate the 4 cam-bolts (J) into
holes in top panel (A).
Step 6: Place the cam-bolts (J) into
holes in panel (B/C/D) and attach using
cam-locks (K).
Step 7: Attach the 4 wooden pegs (G)
to rear panel (E) using 4 screws (H).
(O)
Figure 4
Step 8: Cover cam-locks (K) with
cotton mats (O) provided.

Figure 5
Locate the wall mirror on a solid wall and
at a comfortable height off the floor,
normally eye level.
Measure the wall and mark the wall
mirror width and height. See Figure 5.
Please mount at least one screw directly
into a wall stud. Wall anchor is not
needed when mounting the screw
directly into a wall stud.
Drill two 1/4” holes into
wall
Figure 6
Measure the wall and mark the location
of the center of each of the two screw
mounting holes. See Figure 6.
Using the level, make sure that all two
marks are level on the wall.
Using the power drill and 1/4” drill bit,
drill two 1/4” holes through the
wallboard at the mounting hole marks.
Eye Level
21"
24"
14-1/2"
20-1/16"3/4"

1/4” Hole Screws
Anchor
Figure 7
NOTICE
Make sure not to drill into electrical
wiring or plumbing pipes.
Step 9: Insert one of the furnished
plastic anchors into each of the two 1/4”
holes.
See Figure 7.
Make sure that the wall anchor is flush
with the wall.
NOTE: It may be necessary to use a
small hammer to gently tap the anchor
into place.
Step 10: Using the phillip head
screwdriver install one screw into each
of the anchors. See Figure 7.
Turn the screw in until there is a gap of
1/4” between the head of screw and the
wall surface.
1
2
3
Figure 8
Step 11: Install the wall mirror (1, Figure
8) onto the two mounting screws using
the mounting holes (2, Figure 8). The
proper and secure mounting of the wall
mirror is when the top edge of each of
the mounting holes is resting securely on
the mounting screw (3, Figure 8).
NOTICE
Using the level, check to make sure that
the wall mirror is horizontally level and
vertically plumb (straight up and down).
1/4"Gap

We
’d love to hear from you! Email us photos of our products in your home
at [email protected]
and we might feature it on our site or use it to model
one of our inspirational photos.
“PARTS WILL BE SENT IF AVAILABLE FROM SEI”
Parts Replacement Form
Customer Information
Name __________________________________________
Address __________________________________________
City/ State/ Zip code _________________________________
Phone Number _________________________________
Please indicate where you purchased this item: Store/ Website/ Catalog
_________________________________________________________
Please indicate color/ size/ style number:
__________________________________________________________________
Style No Parts Letter Parts Description Quantity Needed
Missing or damaged hardware and/or parts will be replaced free charge.
We do not sell
parts. Southern Enterprises Inc. will provide replacement parts for only those items
purchased within the last 9 months.
If this product has not been purchased from our
retail affiliates (within 9 months), we are under no obligation to provide parts or
replacements merchandise. Part will no
t be available under no obligation to provide
parts or replacements merchandise. Parts will not be available for arriving fully
assembled.
Customer Service 1-800-633-5096
[e-mail]
Southern Enterprises, Inc.
600 Freeport Pkwy Ste: 200
Coppell TEXAS 75019