SEI Parita HZ105600TX User manual

Page |
1
PO#:
HZ105600TX
Parita Bar Cabinet
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seidal.com

Page |
2
1) Quantity
of 1
Top Panel
2) Quantity
of 1
Left Side Panel
3) Quantity
of 1
Right Side Panel
4) Quantity
of 2
Middle Panels
5) Quantity
of 1
Upper Shelf Panel
6) Quantity
of 2
Side Shelf Panels
7) Quantity
of 1
Back Panel
8) Quantity
of 1
Lower Shelf Panel
9) Quantity
of 3
Small Middle Panels
10) Quantity
of 2
Side Small Middle Panels
11) Quantity
of 1
Cross Panel
12) Quantity
of 1
Bottom Panel
13) Quantity
of 1
Upper Back Panel
14) Quantity
of 1
Left Side Frame
15) Quantity
of 1
Right Side Frame
Parita Bar Cabinet
Parts List
Please review all parts and hardware before disposing of any packaging. Before beginning assembly, separate
each type of hardware. Carefully study the diagrams below and check that you have all parts indicated. Call
Customer Service if missing hardware. Using the incorrect hardware will cause damage.

Page |
3
16) Quantity
of 2
Front Cross Panels
17) Quantity
of 1
Lower Cross Panel
18) Quantity
of 1
Left Door
19) Quantity
of 1
Right Door
20) Quantity
of 1
Drawer Face Panel
21) Quantity
of 1
Left Drawer Side Panel
22) Quantity
of 1
Right Drawer Side Panel
23) Quantity
of 1
Drawer Back Panel
24) Quantity
of 1
Drawer Cross Panel
25) Quantity
of 1
Drawer Bottom Panel
26) Quantity
of 8
Article Wine Racks
27) Quantity
of 1
Shelf Glass

Page |
4
A) Quantity
of 30
Cam Bolts
B) Quantity
of 30
Cam Locks
C) Quantity
of 50
Wood Dowels Dia. 5/16” x1-1/4”L
D) Quantity
o f 20
Bolts Dia. 1/4x1-1/4”L
E) Quantity
o f 16
Spring Washers Dia. 1/4”
F) Quantity
o f 16
Flat Washers Dia. 1/4”x3/4”
G) Quantity
o f 1
Allen Wrench
H) Quantity
o f 26
Screws Dia. 5/32” x 1"L
I ) Quantity
of 18
Screws Dia. 1/8” x 1/2”L
J) Quantity
of 4
Hinges
K) Quantity
o f 24
Screws Dia. 1/8” x 5/8”L
L) Quantity
o f 2
Magnet Plates
M) Quantity
o f 1
Magnet
N) Quantity
o f 2
Screws Dia. 1/8” x 1/2”L
O) Quantity
o f 2
Knobs
P) Quantity
of 6
Gaskets
Q) Quantity
o f 2
Bolts Dia. 5/32” x 3/4”L
R) Quantity
of 2
Knobs

Page |
5
S) Quantity
o f 4
Bolts Dia. 5/32” x 1-1/8”L
T) Quantity
o f 4
Shelf Pins
U) Quantity
o f 2
Bolts Dia. 1/4x1-3/4” L
V) Quantity
of 9
Small Cam Bolts
W) Quantity
of 9
Small Cam Locks
X) Quantity
of 2
Wood Plugs
Y) Quantity
of 10
Cotton Mats
Z) Quantity
of 2
Anti-Tipping Hardware
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew the
finish. Avoid rubbing or scratching the surface
with rough or abrasive objects.
For replacement parts or questions, please call
Customer Service at 1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
6
Figure 1
Start with fingers to help align screws.
Insert Wood Dowels (C) into holes on Top
Panel (1) and both Side Shelf Panels (6).
Use Screws (H) to attach Article Wine Racks
(26) to Top Panel (1) and both Side Shelf
Panels (6).
Tighten screws with Phillips screwdriver.
Figure 2
Start with fingers to help align cam bolts.
Insert Cam Locks (B) into holes on Middle
Panels (4).
Screw Cam Bolts (A) into threaded holes on
Upper Shelf Panel (5).
Attach Upper Shelf Panel (5) to Middle Panels
(4) using Cam Bolts (A) and Wood Dowels (C).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Cover Cam Locks (B) with Cotton Mats (Y)
provided.
Parita Bar Cabinet
Assembly Instructions

Page |
7
Figure 3
Insert Cam Locks (B) into holes on Back Panel
(7).
Screw Cam Bolts (A) into threaded holes on
Upper Shelf Panel (5).
Attach Upper Shelf Panel (5) to Back Panel (7)
using Cam Bolts (A).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Figure 4
Turn assembled unit upside down.
Insert Small Cam Locks (W) into holes on both
Side Small Middle Panels (10).
Screw Small Cam Bolts (V) into threaded
holes on Upper Shelf Panel (5) and Lower
Shelf Panel (8).
Attach Upper Shelf Panel (5) and Lower Shelf
Panel (8) to all Small Middle Panels (9 & 10)
using Small Cam Bolts (V).
Tighten by rotating Small Cam Locks (W)
clockwise with Phillips screwdriver.
Cover Small Cam Locks (W) with Cotton Mats
(Y).
Attach both Shelf Panels (6) to Middle Panel
(4) using Wood Dowels (C).
5
4

Page |
8
Figure 5
Insert Cam Locks (B) into holes on assembled
unit and Cross Panel (11).
Screw Cam Bolts (A) into threaded holes on
Left Side Panel (2) and Right Side Panel (3).
Attach Left and Right Side Panels (2 & 3) to
assembled unit and Cross Panel (11) using
Cam Bolts (A) and Wood Dowels (C).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Figure 6
Use Bolts (D) and Wood Dowels (C) to
connect Bottom Panel (12) to assembled unit.
Tighten bolts using Allen Wrench (G).

Page |
9
Figure 7
Attach Upper Back Panel (13) to assembled
unit with Screws (I).
Tighten screws with Phillips screwdriver.
Figure 8
Turn assembled unit right-side up.
Insert Cam Locks (B) Wood Dowels (C) into
holes on assembled unit.
Screw Cam Bolts (A) into threaded holes on
Top Panel (1).
Attach Top Panel (1) to assembled unit using
Cam Bolts (A) and Wood Dowels (C).
Tighten by rotating Cam Locks (B) clockwise
with Phillips screwdriver.
Cover Cam Locks (B) with Cotton Mats (Y).
Insert Screw (H) into the corresponding hole
on Cross Panel (11) and into Bottom (12).

Page |
10
Figure 9
Use Bolts (D), Flat Washers (F), Spring
Washers (E) and Wood Dowels (C) to connect
Front Cross Panels (16) and Lower Cross
Panel (17) to Side Frames (14/15).
Tighten bolt using Allen Wrench (G).
Figure 10
Turn the assembled unit from Figure 8
upsidedown.
Use Bolts (D), Flat Washer (F), and Spring
Washers (E) to connect assembled unit from
Figure 9 to assembled unit from Figure 8.
Tighten bolts using Allen Wrench (G).
C

Page |
11
Figure 11
Insert Shelf Pins (T) into holes on middle
panels.
Insert adjustable Glass Shelf (27) onto pins.
Make sure shelf pins stably hold adjustable
glass shelf.
Figure 12
Start with fingers to help align screws.
Attach Hinges (J) to Side Panels (2/3) and
Doors (18/19) with Screws (K). Tighten screws
with Phillips screwdriver.
Attach Magnet Plates (L) to inside of doors with
Screws (N). Tighten screws with Phillips
screwdriver.
Attach Knobs (O) with Gaskets (P) to doors with
Bolts (Q). Tighten bolts with Phillips screwdriver.
Attach Magnet (M) to unit using Screws (I).
If cabinet is not level, please adjust leg’s
adjustable foot pad by hand.
Cover holes on legs with Wood Plugs (X).

Page |
12
Figure 13
Attach Drawer Cross Panel (24) to Drawer
Front Panel (20) with Small Cam Bolt (V) and
Small Cam Lock (W).
Attach Drawer Side Panels (21/22) to Drawer
Back Panel (23) using Screws (H). Tighten
screws with Phillips screwdriver.
Insert Drawer Bottom Panel (25) into grooves
of Panels (21/22/23).
Attach Drawer Front Panel (20) to unit using
Screws (H).
Attach Knobs (R) with Gaskets (P) to Drawer
Front Panel (20) using Bolts (S).
Tighten bolts and screws with Phillips
screwdriver.
Figure 14
Insert drawer into assembled unit.
Make sure slides glide smoothly in and out.
Note: There is a lever located on male slide
for bottom drawer slide. Push lever to
either side in order to detach male slide
from female slide.

Page |
13
Figure 15
Start with finger to help align screws.
Attach Brackets (Z) to Back Panel using
Screws (Z). Tighten screws with Phillips
screwdriver.
Mark two desired locations on wall, same
distance as Brackets (Z) on back of unit. Drill
two 3/16" holes on wall. Insert Plastic Anchors
(Z) into holes on wall. (Use hammer to help.)
Attach Brackets (Z) to wall using Screws (Z).
Tighten screws using Phillips screwdriver.
Move this item close to wall Brackets (Z) and
tie in both Brackets (Z) with Plastic Straps (Z)
as shown.
Anti-tipping hardware must be used
for this product to avoid tipping and
injury.
Figure 16
Now your Parita Bar Cabinet is ready to use!

Page |
14
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame.
Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not
responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days
of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas), Mon-Fri
9am – 4pm CST, or email us at [e-mail]. Please ask for customer service representative for issues
involving damages or replacement parts. Please ask for technical assistance representative for any issues with product
and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019