SEI Morgana Console CM501400TX User manual

For assistance with assembly contact:
Southern Enterprises Inc.
Customer Service 1-800-6 -5096
[e-mail]
www.seifurniturestore.com
Page 1
CM501400TX
Morgana Console
Assembly Instructions

A. Quantity
of 4
Bolt 1/4x3/4”L
B. Quantity
of 6
Bolt 1/4x2-1/4”L
C. Quantity
of 8
Bolt 1/4”x2-3/4”L
D. Quantity
of 1
Allen wrench
E. Quantity
of 22
Screw Φ1/8”x5/8”L
F. Quantity
of 8
Screw Φ1/8”x3/4”L
G Quantity
of 8
Screw Φ1/4”x1/2”L
H Quantity
of 8
Back panel parts
I Quantity
of 16
Wood dowel Φ5/16”x1-1/4”L
J Quantity
of 8
Cam bolt
K Quantity
of 8
Cam Lock
L Quantity
of 8
Cover
M Quantity
of 1
Left Arm Hinge
N Quantity
of 2
Hinge
O Quantity
of 2
Hinge
P Quantity
of 4
Plastic cap
Q Quantity
of 2
Bumper pipe
R Quantity
of 2
Bumper base
S Quantity
of 2
washer
T Quantity
of 1
Adjustable level
U Quantity
of 2
Wall anchor
CM501400TX Morgana Console
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded surface
like carpet or a blanket. Check that you have all the parts indicated. Call customer service if any hardware is missing.
Before beginning assembly, carefully study the diagrams below and sort your hardware according to the pictures. Using
the incorrect hardware will cause damage.

V Quantity
of 6
Washer
W Quantity
of 2
Anti-tipping hardware
X Quantity
of 2
Wood screw Φ1/8”x1-1/2”L
Y Quantity
of 1
Right Arm Hinge
1 Quantity
of 1
Top Panel
2 Quantity
of 1
Bottom Panel
3 Quantity
of 1
Left side panel
4 Quantity
of 1
Right side panel
5 Quantity
of 1
Left vertical panel
6 Quantity
of 1
Right Vertical panel
7 Quantity
of 1
Middle Back Panel
8 Quantity
of 2
Side Back Panel
9 Quantity
of 1
Small Door
10 Quantity
of 1
Big Door
11. Quantity
of 2
Side leg
12 Quantity
of 1
Middle small leg
Page

Figure 1
Attach Hinges (O) and Washers
(S) to Small Door (9) with Screws
(E).
Attach Hinges (N) and Washers
(S) to Big Door (10) with Screws
(E).
Tighten Screws (E) with Phillips
screwdriver (not included).
Figure 2
Attach the Plastic Caps (P) to
Side Legs (11).
Attach Adjustable Level (T) to
Middle Small Leg (12)
Page 4
CM501400TX MORGANA CONSOLE
Assembly Instructions

Figure 3
Attach Bumper Bases (R) to
Top Panel (1) with Screws (E).
Tighten Sscrews with phillips
screwdriver (not included).
Figure 4
Insert Bumper Pipes (Q).
Note:
Bumper Pipes (Q) should be
facing the front.
Page 5

Figure 5
Attach Legs (11) to the Bottom
Panel (2) with Bolts (A) and
Bolts (B).
Tighten Bolts with Allen
Wrench (D).
Figure 6
Attach Side Panels and Vertical
Panels (3/4/5/6) to Bottom
Panel with Bolts (C).
Tighten Bolts with Allen
Wrench (D).
Page 6

Figure 7
Insert Back Panels (7/8) into
pre-assembled unit from Figure
6.
Figure 8
Insert Cam Locks (K) into
holes on pre-assembled unit
from figure 7.
Screw Cam Bolts (J) into holes
on Top Panel (1).
Attach Top Panel (1) to
pre-assembled unit from figure
7 by inserting Wood Dowels (I)
and Cam Bolts (J) into
corresponding holes until
panels meet.
Tighten by rotating Cam Locks
(K) clockwise with Phillips
Sscrewdriver (not included).
Cover cam lock holes with
Covers (L)
Page 7

Figure 9
Attach Back Panel Parts (H) to
back of the unit with Screws
(F).
Tighten Screws with Phillips
Screwdriver (not included).
Figure 10
Mark two desired locations on
wall.
Drill two 3/16" holes on wall.
Insert plastic anchors (U) into
the 2 holes on wall.
(When doing this, you will need
a hammer help you).
Page 8

Figure 11
Attach the Anti-tipping
Hardware (W) to Plastic
Anchors with Wood Screws (X)
and Washers (V).
Tighten screw with Phillips
Screwdriver (not included).
Move the unit close to the
Anti-tipping Hardware (W) and
insert Anti-tipping Hardware
(W) through Back Panels (8).
Figure 12
Attach Anti-tipping Hardware
(W) to Top Panel with Washers
(V) and Screws (E).
Tighten screw with Phillips
Screwdriver(not included)
Warning: Anti-tipping
hardware must be used for
this product to avoid tipping
and injury.
Page 9

Figure 13
Attach pre-assembled units
from Figure 1 to pre-assembled
unit from Figure 7 with Screws
(G).
Tighten Screws with Phillips
Screwdriver (not included)
Figure 14
Attach Arm Hinges (M/Y) to
pre-assembled unit from Figure
8 with Screws (E).
Tighten Screws with Phillips
Screwdriver.
Page 10