Seiko Epson DM-MS123 User manual

-1
SR-600 Option
MSR Unit
DM-MS123
User’s Manual
401324201

0
Caution
No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation.
The contents of this document are subject to change without notice.
Please contact us for the latest information.
While every precaution has been taken in the preparation of this
document, Seiko Epson Corporation assumes no responsibility for
errors or omissions.
Neither is any liability assumed for damages resulting from the use of
the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the
purchaser of this product or third parties for damages, losses, costs, or
expenses incurred by the purchases or third parties as a result of:
accident, misuse, or abuse of this product or unauthorized
modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's
operating and maintenance instructions.
EPSON is registered trademarks of Seiko Epson Corporation.
Copyright 2000 by Seiko Epson Corporation, Nagano, Japan.

1
EMC and Safety Standards Applied
Product Name: DM-MS123
Model Name: M171A
The following standards are applied only
to this equipment that are so labeled.
Europe: CE marking
Safety:EN60950
North America:EMI: FCC/ICES-003
Class A
Safety: UL 1950/CSA C22.2
No. 950
Japan: EMC: VCCI Class A
JEIDA-52
Oceania: EMC: AS/NZS 3548
Class A
WARNING
You are cautioned that changes or
modifications not expressly approved by
SEIKO EPSON Corporation could void
your authority to operate the equipment.
CE Marking
This equipment conforms to the following
Directives and Norms:
Directive 89/336/EEC
EN 55022 Class A
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
FCC Compliance Statement For
American Users
This equipment has been tested and found
to comply with the limits for a Class A
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference when the equipment
is operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a
residential area is likely to cause harmful
interference, in which case the user will be
required to correct the interference at his
own expense.
FOR CANADIAN USERS
This Class A digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du
Canada.
FOR TAIWANESE USERS

2
Handling Guidelines
Notes and precautions in this manual are identified by their level of
importance, as defined below.
WARNING
Provides information that must be followed carefully to avoid
bodily injury.
CAUTION
Provides information that must be observed to prevent
damage to the equipment or loss of data.
WARNING
❏Turn off the SR-600 if it produces smoke, a strange odor, or unusual
noise, and then contact your dealer or an EPSON service center for
advice.
❏Never disassemble or modify this product.
Doing so may result in injury, or fire.
❏Do not allow foreign objects to fall into this product.
Penetration by foreign objects may lead to fire.
❏If water spills inside, turn off the SR-600 immediately and contact
your dealer or an EPSON service center for advice. It may lead to
injury, or fire.

3
CAUTION
❏Do not locate SR-600 to high humidity or dust levels.
It may cause a damage, or fire.
❏Do not use the card listed below. Using these card may cause a
damage or a loss of function.
- Surface of the magnetic card is dirty -Surface of the card is wet
- Foreign objects are attached on the card - The card with clack or
damage
❏Do not insert any object other than the magnetic card in the
magnetic card reading portion .
It may cause a damage or a deterioration of function.
Supplied Items
Check that the items shown below is contained in DM-MS123 and none of the
items are damaged.
Refer the developer’s guide for the attachment guideline.
MSR unit User’s Manual
(This document)
Connector
Cable

4
Specifications
General Specifications
Magnetic Card: ISO7811, JIS X6301 type I
track 1, 2 ,3
External Interface: LCD Unit (Connected to DM-LS121S and
DM-LS121T)
Keyboard Firm: Version 3.01 or above
Dimensions and Weight
Dimensions (width) ×(length) ×(height):46 mm ×174mm ×56mm
Weight: Approximately 270g
Environmental Specificatins
Temperature(during operation): 5 to 35 Celsiuis
Temperature(during saving): -10 to 50 Celsiuis
Humidity(during operation): 30 to 80%RH (no condensation)
Humidity(during saving): 30 to 90%RH (no condensation)
Water Resistance : IEC 529 IPX1 equivalent
Reliability
Life of Magnetic Head: 300,000 Times
(Magnetic card readable time）