SellEton Scales SL-905 User manual

www.selletonscales.com
SL-905 INDICATOR
USER’S MANUAL

TABLE OF CONTENTS
Safety Precautions 1
Preparations and Set Up 1
Features 2
Specications 3
Power Supply 4
Displays 5
Display and Key Descriptions 6
Operating Instructions 7-9
Calibration 10
Indicator Parameter Settings 12-16
Helpful Denitions 17
Connectors 18-19
RS232 Serial Output Format 20-23
4-20 mA Analog Output 24
Relay Output 25
Troubleshooting 26
Q&A 27
Contact Us 28

1
SAFETY PRECAUTIONS
For safe operation of the weighing indicator, please follow these
instructions:
●Calibration inspection and maintenance of the indicator are prohibited by non-pro-
fessional staff
●Please ensure that the indicator rests on a stable surface
●The indicator is a piece of static sensitive equipment; Please cut off power during
electrical connections
●Touching the internal components by hand is prohibited
●DO NOT exceed the rated load limit of the unit
●DO NOT step on the unit
●DO NOT jump on the scale
●DO NOT use this product if any of the components are cracked
●DO NOT use for purposes other then weight taking
●To avoid damaging the battery do not keep charger plugged in once battery is fully
charged
●Make sure the weight is not over the Max capacity as it could damage the load cell
inside
● Material that has a static electric charge could inuence the weighing. Discharge
the static electricity of the samples, if possible. Another
solution to the problem is to wipe both sides of the pan and the top of the case with
an anti-static agent
Please take anti-static prevention measures
Any accumulated charge on the body of the human operator should be discharged rst
before opening the protective container with ESDS devices inside. The discharge can
be accomplished by:
●Putting a hand on a grounded surface or, ideally, by wearing a grounded Anti-static
Wrist Strap and an Anti-static Mat
PREPARATION & SET UP
●Plug into a wall outlet to avoid interference with other wirings
●Turn on the indicator while there is no load
●Calibration may be required before weighing when the scale is initially installed or
moved from a location

2
FEATURES
Suitable for Bench scales, oor scales and truck scales, this indicator works with 32bit
CPU and 24bit high precision ADC. It is made with a Stainless Steel housing. Excellent
performance make it proper for varied interface function. Waterproof connector and
cable connection xed inside.
●Multiple weighing units: (lb/kg)
●Gross/Tare/Pre-Set Tare/Zero
●Multiple Hold functions
●Count weighing
●Accumulation weighing
●Check weighing
●Overload / Underload indication
●Connects to printer
●Splash proof keyboard and display
●Connects to a Remote Display/Scoreboard
●Power saving mode
●Can connect to a PC or printer for data logging (optional)
●Wireless capability (optional)
● 20 mm Letter LED display
●Rechargeable battery
● RS232 output
Technical Parameters
● Accuracy class: 5000 e
● Resolution - Display: 30,000 ; ADC: 2,000,000
● Zero stability error: TK0 < 0.1μV//K
● Span stability error: TKspn < ± 6 ppm//K
● Sensitivity (internal): 0.3 μV / d
● Input voltage: -30 to +30mV DC
● Excitation circuit: 5 VDC, 4 wire connection, 12 load cell of 350ohm max
● AC power: AC 110V
● Battery 6V4Ah
● Operation temperature: -10 °C ~ +40 °C
● Operation humidity: ≤85%RH
● Storage temperature: -40 °C ~ +70 °C (32-104°F)
● Weight: 7lbs (3.2kg)
● Dimensions: 11.25” x 4” x 9.5” (260x160x80mm)

3
ON/OFF
Hold Unit
Count Esc
Tare Set
Check Print
Zero
Total Del
12 3
456
789
0
Gross NetHold Total pcs lb kg Battery
zero
Hi
OK
Lo
SL-905
#
10.25”
11.25”
9.5”
6.25”
3.25”
4”
3.14”
5.11”
1.77”
SPECIFICATIONS
FIGURE 1: INDICATOR MEASUREMENTS

4
POWER SUPPLY
AC Adapter
We recommend to plug into a wall outlet to avoid interference with other wirings.
Battery
Please charge the internal battery fully before rst time use. To keep the battery in best
condition, fully discharge the battery every month by leaving the indicator on until the
indicator powers off, and then recharge fully. If the battery is not going to be used for a
long period of time it is recommended to remove it to avoid leakage.
● When the Battery is low the battery indicator light ashes red
●During charging the red light will stay lit
●The light will turn green once fully charged
SL-905 (LED)
Keypad and Display
OVER
ACCEPT
UNDER
0
Gross Net Hold Total Pcs LB KG
Battery
Cap. _______x D_____
ON/OFF
HOLD UNIT CHECK PRINT
TOTAL DEL COUNT ESC
TARE ZERO SET
1 2 3
4 5 6
7 8 9
0
C#
MODEL SL-905 CLASS III

5
DISPLAY AND KEY DESCRIPTION
HOLD Holds the weight on the scale Depending on the parameter setting
UNIT Shifts between weighing units
CHECK Checking the record by number
PRINT Print the weighing data
TOTAL In gross mode: get the tare weight
In net mode: clear the tare, get the Gross
DEL Delete the previous weighing data and the saved record
COUNT Use the scale to count product based on a sample weight
ESC Back to weighing
TARE 1. Zero’s the scale. Used when using a container to hold objects
2. Clears the tare to see the gross weight
ZERO Zero’s the scale
SET Conrm the action
ON/OFF Powers the Indicator On or Off if held for 2 seconds
CClear the input
#Conrm the input
The scale is at zero
The scale is stable
Gross Shows you are in Gross weight mode (includes tare); default mode
Net Shows you are in Net weight mode (weight without tared weight)
Hold Shows you are in Hold mode
Total Shows you are in Accumulation mode
Pcs Shows you are in Counting mode
LB The weight is shown in pounds
KG The weight is shown in kilograms
Battery Flashes red = low battery, Solid red = charging, Green = fully charged
Over Flashes when weight is higher than set alarm parameter
Accept Flashes when weight is within the set alarm parameters
Under Flashes when weight is lower than set alarm parameter

6
OPERATING INSTRUCTIONS
Power On
●Turn on the power by pressing the ON/OFF button for 2 seconds. Once on, the scale
will ash the voltage and then begin to auto-check and count down from 0-9
sequentially before entering the weighing mode
Note: Anything on the scale before powering on will automatically be tared out.
Zeroing
●The zero function is used only when the scale is empty and is not at zero due to
material build up
● Pressing the ZERO key while the scale is stable will reset your scale to 0
●Depending on what your manual zero range parameter is set to, you can zero out
any weight within your set selection, after that you will receive an error and will
need to tare out the weight
Unit Selection
●To switch between measuring units (kg/lb) press the UNITS key
Tare Function
To Tare: When in gross mode, press TARE to enter net mode and tare out the weight
●The Tare function is used when you only wish to see the current change in weight,
not the entire amount of weight that is on the scale
●When the indicator is in gross mode (gross light is shown) pressing the TARE key
will Tare the current weight on the scale and enter the net mode (net light shown)
● For example if you are using a container add the container to the scale, press tare
and the display will show the tare symbol and reset back to 0
●Add your product to the scale to weigh without the weight of the container
●To exit Tare mode press the TARE key again to enter gross mode and you will see
the total weight of the container and the product
Note: If you remove the container the scale will show the minus weight of the container
To use a pre-set tare weight
●Press and hold the TARE key and SET key at the same time
● Input the weight you want tared on the keypad
● Press TARE key to conrm
● Press TARE to reset back to 0
TARE

7
Accumulation
●The accumulated function is used to add multiple weights and total them together
● You can add up to 999 different weights together
● In weighing mode load the rst weight, once stable press the TOTAL key to enter
the accumulated mode. The “total” light will display
● Remove the rst weight and add the second weight to the scale
● Once stable press TOTAL key to add the weight to the accumulated total
● Repeat previous steps until all desired weights have been added to the total (max 999
times)
● When you are done and want to display the accumulated total, press the TOTAL and
SET key together. The accumulated number “n###” (the number of weights you
are adding together) will ash on the display followed by the total
● If you want to print the accumulated total, hold the PRINT key for one second
●To exit accumulated mode, press the ESC key
● To delete the saved weights press the DEL key followed by the set key to conrm
●Repete this process to cleaer all saved weights
TOTAL
TOTAL
TOTAL SET
+
DEL SET
Print
● If the indicator is connected to a printer and the weight on the scale is stable press the
PRINT key to print the current weight
Note: In tare mode the printer can not print if negative weight is shown

8
Counting Function
●The counting function is used to count a high volume of identical parts. You can do
this by setting a sample and then either adding to the sample or taking away from
the sample to count the number of objects on the scale
● In weighing mode: press COUNT to enter count mode
●Then press COUNT and SET at the same time to set your sample with the keypad
● (ex. If you are counting pencils, you would add a sample of pencils to the scale, if
you add 50 pencils to the scale you would enter 50 on the keypad.)
●Press #on the keypad to set your sample
●The scale is now ready to start counting, load your product on the scale and the
indicator will show the quantity
● (ex. if you add 450 pencils to your sample of 50, the scale will read 500 pencils)
●To see the weight on the scale press COUNT
●To exit counting mode press the ESC key
● If you want to count a different product hold the COUNT and SET keys together to
enter a new sample
+ 450 pencils
COUNT
SETCOUNT +
Hold
There are 4 different hold functions you can choose from in the C11 parameter
1. Peak Hold: Grabs the highest weight (for materials testing, ie. tension and pulling
force)
●Press the HOLD key then add weight to the scale
●The indicator will show the highest weight it recorded and hold it on the screen until
a higher weight is placed on the scale
2. Manual Hold: Grabs the current weight and holds it so it will not change/uctuate
● While weighing, press HOLD and the indicator will hold the current weight on the
screen until HOLD is pressed again
3. Auto Hold: If the weight on the scale is above 20d (20 x division) and is stable,
the indicator will hold that weight on the screen for 3 seconds then go back to general
weighing
●Pressing the hold key is unnecessary, holding is done automatically when the scale
is stable
4. Average Hold: Used for animal weighing, the indicator will display the average
weight sampled from 3 seconds

Recipes
Recipes allows you to store formulas for different products you may continuously be
weighing, and creates a quick easy way to streamline your weighing.
For example: If you are selling 2 lb bags of cherries, you would create a recipe by set-
ting a tolerance using upper and lower limits. This tolerance allows you to quickly sepa-
rate multiple 2 lb bags of cherries. For this example we are going to use a tolerance of 0.1
lbs. Meaning we would set our upper limit to 2.10 lbs and our lower limit as 1.90 lbs. We
are telling the scale, that any weight taken out of the container between 1.9 lbs - 2.1 lbs
is acceptable, anything higher or lower is not. Now that our recipe is set add your large
container of cherries on the scale. Then tare out your container of cherries, setting the
scale to 0. Now if you start scooping out cherries from the container into a bag, the scale
will read in negative (ex. -1.5 lbs) until the amount set in our recipe is reached. When you
have taken out ~2 lbs (what your tolerance is set to) the scale will reset back to 0. Then
the process can be repeated again, take out ~2 lbs of cherries until the scale reads 0.
To set these formulas:
1. Press SET, the screen will show what recipe number you are on, the default is 1. If it
is not on 1, use the keypad to enter the recipe number you would like to set. (up to 99
recipes can be saved)
2. Press # to conrm that number
3. You will now be back in weighing mode the screen will show 0
4. Press SET and ESC at the same time to enter the settings mode
5. use the keypad to input 13 followed by # to conrm
6. Use the keypad to enter your Upper Limit, followed by # to conrm (ex. 2.10)
7. The screen will show C14, press #to enter this setting
8. Use the keypad to enter your Lower Limit, followed by the # key to conrm (ex. 1.90)
9. The screen will show C15, press ESC to save and return to weighing mode
10. Then place your container on the scale, The screen will show you the total weight
11. Press TARE to set the scale back to 0
12. After pressing tare you are able to remove product from the scale until you are within
your set tolerance and the scale reads 0. (ex. 1.9 - 2.1 lbs)
To use already set formulas:
1. In weighing mode, press SET, followed by the number the recipe is saved under
2. Press # to conrm
3. Add your product to the scale, Then press TARE
4. You can now start removing product and the scale will read 0 when its within the set
tolerance
5. To change recipes, press SET followed by the number the recipe is saved under
9

10
CALIBRATION PROCEDURE
1. Turn on the scale by holding ON/OFF .
2. Press SET and ESC together to access the setup menu.
3. If done correctly, the display should now show
4. Press # to access the C1 channel. The display should show [C01 01].
5. On they keypad enter which unit you want to calibrate in (1 = kg, 2 = lb).
6. Press #to save your value. The display will now show
7. Press # to access the C2 channel. The display should show [C02 00].
8. Use the keypad enter the setting for the decimal places desired (The C2 channel is
used to adjust the decimal point on the scale. A value of 1 means there is one digit
behind the decimal point 1= 0.0, a value of 2 = 0.00)
9. On they keypad set your value. The display will now show
10. Press # to access the C3 channel. The display should show [C03 01].
11. On they keypad enter the value of your desired graduation.
(The C3 channel adjusts the divisions on the scale. A value of 1 selected and C2 set
to 1, the scale will read in 0.1 lb. increments.)
12. Press #to set your value. The display will now show
13. Press # to access the C4 channel. The display will show [000000].
14. On they keypad enter the maximum capacity you want to use for your scale.
(The C4 channel is used to enter in the max capacity of the scale; Make sure the
number you enter does not exceed the max capacity of your scale.)
15. Press #to set your value. The display will now show
16. Press #to access the C5 channel. The display should show [C05 00].
17. The C5 channel calibrates zero on the scale. Make sure the scale is empty.
18. Press 1 on the keypad to change the value to 1.
19. Press # to zero calibrate. The display will count down from 10-1 while the scale is
calibrating. When the display shows 0 the zero calibration is complete.
20. Press #to to continue. The display will now show
21. Press # to access the C06 channel. The display will show [C06 00].
22. The C6 channel is used to calibrate the scale with a known weight. Press 1 on the
keypad to set the value of C6 to [C06 01].
23. Press # to to continue. The display will ash SPAN, and then show [000000].
24. On the keypad enter the weight of the calibration weight you will use
(must be at least 10% of your max capacity you set in C04.
25. Place your calibration weight on the empty scale and #.

11
CALIBRATION CONT.
26. The scale will count down from 10 to 0. Once 0 has been reached, the display will
show CALEnd.
27. Press #to continue. The display will now show
28. Press ESC to save and exit the setup menu.
29. The scale has now been calibrated. The display will show the value of the calibration
weight on the scale.
30. If the scale does not show the value of the calibration weight, check that the feet on
the platform are not screwed in too tightly, and verify that the platform is level.
31. Unload the scale; the display should read 000000.
32. If the scale does not display 000000, check that the feet on the platform are not
screwed in too tightly, and verify that the platform is level.

12
INDICATOR PARAMETER SETTINGS
The parameter settings menu has a calibration section (C01 to C07 explained above) and a
parameter settings section (C08 and up).
To access the calibration section the seal switch (located at one corner of the PCB) must be
OFF. This will allow access to all C01 and up settings. If the seal switch is ON, then only C08 and up
can be accessed by the user. If you break the ofcial seal by opening the back of the indicator to
access the seal switch, you may need to have the indicator recertied. Be sure to adjust the seal
switch back to the original setting after calibration/conguration has been performed.
To enter calibration/parameter settings, follow the procedure below:
1. Press and hold the SET and ESC key at the same time to enter the parameter settings
2. Navigate through the settings (C01 to C45) by using the number keypad
3. Press the #key to enter/edit the parameter setting
Press the ESC key to save and exit settings at any time
Table 1. Indicator Parameter Settings
Function Parameter Settings/Options
Weighing Unit C01 1 = kg
2 = lb
Decimal Setting C02 0 = no decimal
1 = #.#
2 = #.##
3 = #.###
4 = #.####
Graduation Setting
(readability of the least
signicant digit)
C03 options: 1/2/4/10/20/50
Example with no decimal places (ie C02=0)
1 = 1 lb
2 = 2 lb
5 = 5 lb
10 = 10 lb
20 = 20 lb
50 = 50 lb
Maximum Capacity C04 set max capacity ex. 100kg = 0100.00
Zero Calibration C05 0 = zero calibration not needed
1 = set the zero calibration (Please ensure scale is empty and the
stable light is on)
Calibration C06 0 = calibration not needed
1 = ready to calibrate with calibration weight
Restore Default
Settings C07 0 = do not restore
1 = restore to default settings

13
Function Parameter Settings/Options
Hold Function C08 0 = turn off hold function
1 = Peak hold - Grabs the highest weight
2 = Manual hold - Grabs the current weight
3 = Auto hold - Automatically holds data when stable
4 = Average hold - for animal weighing, averages the weight from a
sample of 3 seconds
5 = Auto Average hold - Average hold without the need to press the
hold key
Unit Switch C09 0 = turn off unit switch
1 = turn on unit switch
Power Saving Mode C10 0 = turn off power saving setting
3 = turn off display if no change within 3 minutes
5 = turn off display if no change within 5 minutes
Automatic
Power Off C11 0 = turn off auto power off
1 = power off automatically if no change within 10 minutes
2 = power off automatically if no change within 20 minutes
3 = power off automatically if no change within 30 minutes
4 = power off automatically if no change within 40 minutes
5 = power off automatically if no change within 50 minutes
6 = power off automatically if no change within 60 minutes
Alarm Setting C12 0 = turn off alarm
1 = turn on alarm
Upper Limit Alarm C13 Set upper limit within the max. capacity
Lower Limit Alarm C14 Set lower limit within the max. capacity
Inner Code Display C15 check the inner code (raw data)
Preserved menu C16
Preserved menu C17
Communication
Setting for the RS232
Port
C18 Set the serial interface data output method:
0 = Turn off serial interface data output
1 = Command request mode, connect computer.
2 = Print mode, connect printer
3 = Continuous sending mode, connect computer or display
Preserved menu C19
Manual
Zero Range C20 0 = turn off manually zero setting 1 = ±1% max capacity
2 = ±2% max capacity
4 = ±4% max capacity
Initial Zero Range C21 0 = no initial zero setting
1 = ±1% max capacity
2 = ±2% max capacity
5 = ±5% max capacity
10 = ±10% max capacity
20 = ±20% max capacity

14
Function Parameter Settings/Options
Zero Tracking C22 0= turn off zero tracking
0.5 = ±0.5d d = division
1.0 = ±1.0d
2.0 = ±2.0d
3.0 = ±3.0d
4.0 = ±4.0d
5.0 = ±5.0d
Note: the zero tracking range can not be bigger than manual zero
range
Zero Tracking Time C23 0 = turn off zero tracking time
1 = 1 second
2 = 2 seconds
3 = 3 seconds
Overload Range C24 00 = turn off overload range
01-99d = overload range setting d = division
Negative Display C25 0 = -9d
10 = -10% max. capacity
20 = -20% max. capacity
Standstill Time C26 0 = quick
1 = medium
2 = slow
Standstill Range C27 1 = 1d d = division
2 = 2d
5 = 5d
10 = 10d
Digital Filter
(for ltering moving
weight such as
animals)
C28 0 = turn off dynamic lter
1 = 1 digital lter strength
2 = 2 digital lter strength
3 = 3 digital lter strength
4 = 4 digital lter strength
5 = 5 digital lter strength
6 = 6 digital lter strength
Note: The higher the number, the higher the lter strength
Noise Filter C29 0 = turn off noise lter
1 = 1 digital lter strength
2 = 2 digital lter strength
3 = 3 digital lter strength
Communication Format C41 0 = turn off continuous transmit
1 = format 1
2 = format 2
3 = format 3
4 = format 4
Baud Rate C42 0 = 600
1 = 1200
2 = 2400
3 = 4800
4 = 9600
5 = 19200
6 = 38400
7 = 57600
8 = 115200

15
Function Parameter Settings/Options
Odd-Even Check C43 0 = 8n
1 = 70
2 = 7e
Interval C44 0 = no limit
1 = 100ms
2 = 200ms
3 = 500ms
4 = 1s
5 = stable transmit
Checksum C45 0 = no
1 = yes
Simple Command
Support C46 0 = no
1 = yes
Commanding Format C51 0 = turn off commanding mode
1 = simple commanding
2 = standard commanding
Baud Rate C52 0 = 600
1 = 1200
2 = 2400
3 = 4800
4 = 9600
5 = 19200
6 = 38400
7 = 57600
8 = 115200
Odd-Even Check C53 0 = 8n
1 = 70
2 = 7e
Response Format C54 0 = format 1
1 = format 5
2 = format 4
Slave ID C55 0-99
Print Mode C61 0 = turn off printing mode
1 = turn on printing mode
Baud Rate C62 0 = 600
1 = 1200
2 = 2400
3 = 4800
4 = 9600
5 = 19200
6 = 38400
7 = 57600
8 = 115200

16
Table 3. Default Parameter Settings
Function Parameter Default
Weighing Unit C01 1
Decimal Setting C02 0
Graduation Setting C03 1
Maximum Capacity C04 10000
Zero Calibration C05 0
Calibration C06 0
Restore Default C07 0
Hold Function C08 0
Unit Switch C09 9
Power Saving Mode C10 0
Automatic Power Off C11 0
Alarm Setting C12 01
Upper Limit Alarm C13 000000
Lower Limit Alarm C14 000000
Inner Code Display C15 999999
Communication Setting C18 1
Manual Zero Range C20 2
Initial Zero Range C21 10
Zero Tracking C22 0.5
Zero Tracking Time C23 1
Overload Range C24 9
Negative Display C25 10
Standstill Time C26 1
Standstill Range C27 2
Digital Filter C28 0
Noise Filter C29 2
Communication Format C41 2
Baud Rate C42 1
Odd-Even Check C43 0
Interval C44 1
Checksum C45 0
Simple Command C46 0
Commanding Format C51 1
Baud Rate C52 4
Odd-Even Check C53 0
Response Format C54 0
Slave ID C55 0
Print Mode C61 1
Baud Rate C62 4

17
BATTERY INSTALLATION
The indicator works with AC power, please note the voltage is proper and check if the AC
power side is earthing.
Voltage transformer and stable circuit is build in the indiciator please dont open it with-
out professional instruction.
Stable Circuit connection
J1 Inditial level for AC power input and voltage transfomer
J2 Second level for voltage transformer
F1 220V 0.25A fuse
PCB indicator power connection
Postive battery connect with BAT+ , negative batter connect with BAT-

18
SCALE INSTALLATION
OP-905 maxi. Supports 12 x 350ohm load cells. (4 wires or 6 wires load cell) The con-
nection between load cells and indicator is by terminal block. the connection diagram as
below.
4 Wire load cell connection
EXC+, EXC-, SIG+, SIG- (load cell) to EXC+, EXC-, SIG+, SIG- (indicator)
EXC+ and SEN+ to be short circuit
EXC- and SEN+ to be short circuit