Sengled E2D-G73 User manual

smart lighting expert
Sengled Smart Window & Door Sensor G2
E2D-G73

Introduction:
The Sengled Smart Window & Door Sensor G2
enables you to know when a door or window in your
home is opened or closed. With our 3rd-party
integration, you can use the sensor as a trigger to
other smart devices in your home.
Note: A hub is required to control the sensor.
Important Safety Information:
Wireless Specification：Wireless Frequency Range:
2.4GHz (2405MHz~2480MHz, IEEE 802.15.4)
Operating channels Zigbee: 11-26
Maximum Transmitted Output Power: +5dBm
Before installing the Sengled Smart Window & Door
Sensor G2, please read and follow the cautions,
including:
• Suitable for use in operating environment between
5°C and 40°C.
• Indoor use only
Reset Light
1

1
2Test the alignment before you adhere each piece.
3Once your sensor is successfully connected to the
hub, please adhere it to the door or window with
the 3M double sided tapes included. Ensure the
surface to be clean before adhering your sensor.
Note: Install the battery first. Then you will have
one minute to successfully pair it. If fail, then follow
the reset instruction on the next page. Besides, your
sensor will flash twice during the installation
process: once you install the battery, and again
when it’s paired successfully.
Open the Sengled Home App, go to
Devices and click “+”, then choose
Smart LEDs and Accessories (used
with a hub).
Installation Instructions:
To add your Smart Sensor to a Sengled hub, follow the
instructions below. If you DO NOT have a Sengled
Smart Hub and Sengled Home app previously installed,
please install your hub according to its user guide in the
package before installing the sensor. If you have a
3rd-party hub, such as SmartThings or Amazon Echo
Plus, you can also connect Sengled Smart Sensors to
these hubs according to their instructions in apps.
Note: Please make sure your mobile device and
Sengled Smart Hub are connected to the same router.
Both 2.4GHz and 5GHz (refer to wireless transmission
frequency, different with the “5G” used in phones. ) are
supported.
2
Congratulations on successfully installing your
Window & Door Sensor!
Follow the in-app instructions for installation.

Reset Instructions:
Operation:
Change the Battery:
To reset your sensor, please insert the needle
included into the reset hole on the bottom and hold it
for Four to Eight seconds, then release it and the
LED indicator light will flash twice in red. This
indicates that your sensor is starting to pair with your
hub again. It will flash again when successfully
paired.
Your Smart Window & Door Sensor G2 only has one
operational mode. Once installed, the Smart Sensor
requires nothing but battery replacement when
necessary. It can also functions as a trigger, such as
turning on your lights and speakers when a door is
opened. Find more fun in your Sengled Home app.
1. Hold the bottom with
your thumb and press the
cover with your fingers,
then slide downward.
2. Remove the old battery,
then install the new one
with “+ “ side facing
upwards.
3. Replace the cover, and now your sensor is ready to go!
3＋

Frequently Asked Questions:
Make sure your hub is online in the Sengled Home
app by pulling down the home page to refresh the
device status. Open and Close the window or door
will trigger a status update. If your sensor is still
offline, please insert the reset hole with a needle for
one second and it will rejoin. If it continues to
appear offline, then repeat the above step.
Note: Once your sensor is paired, it will flash once
after the battery being replaced successfully, and
then goes into the sleep mode.
If your sensor is not paired, it will try to join your hub
immediately and last for one minute at most before
going into the sleep mode.
Yes. The sensor is compatible with Samsung
SmartThings and Amazon Echo Plus hubs.
4
1. How can the Smart Sensor be connected to the
netwok if it looks offline?
2. Is the Sengled Smart Window & Door Sensor
G2 compatible with other smart hubs?
Yes. The sensor can be monitored via the Sengled
Home app as well as the Amazon Alexa, Google
Home and Samsung SmartThings apps.
3. Can the status of the Smart Window and Door
Sensor G2 be checked from an app?
3V DC (battery type Li+ CR2)
76 mm(2.99’’) x29 mm(1.14’’) x22 mm(0.87’’)
E2D-G73
6 years (depends on usage)

150/V1.0
5
For FCC and IC Statement details, refer to
www.sengled.com/fcc
2-year limited warranty from original purchase date.
To learn more about the Limited Warranty for
Sengled products, please visit
www.sengled.com/warranty
If you encounter any issues, please reach out to your
local Sengled Support team.
Visit the following website for web support:
http://support.sengled.com/
Send emails to:
[email protected] (USA)
[email protected] (CA)
Dial Customer Support Line 1-877-401-5990
10:am-8:00 pm CST on Mon-Fri
11:am-8:00 pm CST on Sat

FCC Regulations
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Changes or modifications not expressly
approved by the manufacturer could void the
user’s authority to operate the equipment.
The antenna(s) used for this transmitter must
not be co-located or operating in conjunction
with any other antenna or transmitter.
For details, reference
www.sengled.com/fcc.
Canada Regulations:
This device complies with Industry Canada’s
licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference;
and
(2) This device must accept any interference,
including interference that may cause
undesired operation of the device.Le
présentappareilestconforme aux CNR

d’Industrie Canada applicables aux appareils
radio exempts de licence.
L’exploitationestautorisée aux deux
conditions suivantes :
(1) l’appareil ne doit pas produire de
brouillage;
(2) l’utilisateur de l’appareildoit accepter
tout brouillageradioélectriquesubi, mêmesi
le brouillageest susceptible
d’encompromettre le fonctionnement.
Caution：
This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmit-ter. This equipment
should be installed and operated with a
minimum distance of 20 centimeters
between the radiator and your body.
Cet emetteur ne doit pas etre Co-place ou ne
fonctionnant en meme temps quaucune
autre antenneou emetteur. Cet
equipementdevrait etre installe et actionne
avec une
distance minimurn de 20centimetres entre le
radiateur et votre corps.