Sennheiser Evolution E 602-II User manual

e 602-II
Bedienungsanleitung
Insruction manual
Notice d‘emploi
Instruzioni per l‘uso
Instrucciones de uso
Manual de instruções
Gebruiksaanwijzing
Stage Microphones




A
B
123
C
125 Hz
250 Hz
500 Hz
1,000 Hz
2,000 Hz
4,000 Hz
8,000 Hz
16,000 Hz
30°
0°
180°150°
120°
60°
90°
0
5
10
15
20
25
dB
30°0°
180°
150°
120°
60°
90°
- 50
- 60
- 70
- 80
- 90
- 40
dBV
50
100 200
500
1,000
2,000
5,000
10,000
20,000
Hz
0°, 1 m
0°, 5 m
12
3
12
3
+ +
12
3
XLR6.3 mm
+
+
12
3
XLR
+
XLR
12
3
6.3 mm
+
+
symmetrical
XLR
XLR
+
D

ENFRITPTNLRUZH ES DE
1
Important safety information
• Please read this instruction manual carefully and completely before
using the product.
• Make this instruction manual easily accessible to all users at all
times.
• Always include this instruction manual when passing the product on
to third parties.
Before operation
• Never open the housing of the product. If products are opened by
customers in breach of this instruction, the warranty becomes null
and void.
• Only use attachments, accessories or spare parts specified by
Sennheiser.
During operation
• Liquids entering the product can short-circuit the electronics or
damage the mechanics. Keep all liquids away from the product.
• Solvents or cleansing agents can damage the surface of the product.
Only use a soft, slightly damp cloth to clean the product.
• Do not expose the product to extreme temperatures.
After operation
• Handle the product with care and store it in a clean, dust-free
environment.
Intended use
Intended use includes:
• having read this instruction manual, especially the chapter
“Important safety information”,
• using the product within the operating conditions and limitations
described in this instruction manual.
“Improper use” means using the product other than as described in
this instruction manual, or under operating conditions which differ
from those described herein.

2
The e 602-II
Feel more bass.
Don‘t just hear it. Feel it. Punching and vibrating, the e 602-II follows
bass instruments down to the low frequencies that shake things up.
The punch of the kick drum keeps its forceful volume at the bottom
of the sound image; the attack remains precise throughout the mic’s
entire frequency response.
The e 602-II hears bass guitars and tubas with the same attention to
detail: warm, dynamic, and always with substance. It sounds as solid
as it looks and, thanks to its lightweight aluminum body, is easy to
position – in studios, clubs, rehearsal rooms, at smaller gigs or for
home recording.
Features
• dynamic microphone with expanded bass range
• fast transient response
• designed for extreme sound pressure levels
• rugged lightweight aluminum body for stable positioning on long
microphone boom arms
• extremely lightweight voice coil construction
• humbucking coil
• integral stand mount
Delivery includes
1 e 602-II microphone
1 pouch
1 instruction manual
Product overview A*
1 sound inlet basket
2 XLR-3 connector
3 integral stand mount
Diagrams can be found on the cover pages.
*

ENFRITPTNLRUZH ES DE
3
Using the microphone
Positioning the microphone on a kick drum B
XMount the e 602-II using the integral stand mount C.
Pos. Resulting sound Commentary
B.1 • much attack
• little resonance
• dry
Position the microphone at a
distance of a few centimeters
from the batter head.
B.2 • less attack
• much resonance
• smooth and voluminous
Position the microphone at the
level of the resonant head.
B.3 • less Attack Position the microphone in the
middle between the batter head
and the resonant head.
For less attack in all three positions, turn the microphone away from
where the beater strikes.
Positioning the monitor loudspeakers
XTo prevent feedback and crosstalk, postion your monitor loudspeak-
ers in the angle area of the highest cancellation of the microphone
(approx. 180°).
Cleaning and maintaining the e 602-II
Caution Liquids can damage the electronics of the product!
Liquids entering the housing of the product can cause a
short-circuit and damage the electronics.
X
Keep all liquids away from the product.
X
Do not use any solvents or cleansing agents .
XUnscrew the sound inlet basket 1.
XRemove the foam insert from the sound inlet basket 1.
XUse a slightly damp cloth to clean the sound inlet basket 1 from
the inside and ouside.
XReinsert the foam insert into the sound inlet basket 1and replace
the sound inlet basket on the microphone and screw it tight.

4
Specifications
Transducer principle dynamic
Frequency response 20 … 16,000 Hz
Pick-up pattern cardioid
Sensitivity (free field, no load) 0.9 mV/Pa (at 50 Hz)
0.25 mV/Pa (at 1 kHz)
Nominal impedance (at 1 kHz) 350 Ω
Min. terminating impedance 1 kΩ
Connector XLR-3
Dimensions Ø 60 mm, length 153 mm
Weight 318 g
The polar diagram and the frequency response curve Ccan be found on
the cover pages.
The XLR-3 connector assignment Dcan be found on the cover pages.

ENFRITPTNLRUZH ES DE
5
Manufacturer Declarations
Warranty
Sennheiser electronic GmbH & Co. KG gives a warranty of 24 months on
this product.
For the current warranty conditions, please visit our website at
www.sennheiser.com or contact your Sennheiser partner.
FOR AUSTRALIA ONLY
Sennheiser goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other reason-
ably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
This warranty is in addition to other rights or remedies under law.
Nothing in this warranty excludes, limits or modifies any liability of
Sennheiser which is imposed by law, or limits or modifies any remedy
available to the consumer which is granted by law.
To make a claim under this warranty, contact
Sennheiser Australia Pty Ltd, Unit 3, 31 Gibbes Street Chatswood NSW
2067, AUSTRALIA.
Phone: [phone], email: [email protected].
All expenses of claiming the warranty will be borne by the person
making the claim.
The Sennheiser International Warranty is provided by Sennheiser
Australia Pty Ltd (ABN 68 165 388 312), Unit 3, 31 Gibbes Street
Chatswood NSW 2067 Australia.
In compliance with the following requirements
• WEEE Directive (2012/19/EU)
Please dispose of this product at the end of its operational lifetime
by taking it to your local collection point or recycling center for such
equipment.
CE Declaration of Conformity
• RoHS Directive (2011/65/EU)
The declaration is available at www.sennheiser.com/download.

e 608
e 614 e 609 silver e 604 e 602-II e 835 e 845 e 865
e 901 e 902 e 904 e 906
e 908 e 914 e 935 e 945
e 965

Sennheiser electronic GmbH & Co. KG
Am Labor 1, 30900 Wedemark, Germany
www.sennheiser.com
Printed in Germany, Publ. 12/16, 515863/A03