Sennheiser ME 36 Dimensions

General Description
Sennheiser’s modular Installed Sound Series microphones kits for podium,
hanging, boundary layer and table stand applications facilitate all possible
installation configurations at affordable prices. At the heart of the series are
three superbly engineered capsules: the ME 34 cardioid, the ME 35 super cardioid
and the unique lobar-patterned ME 36 mini shotgun. Each capsule can interface
with three different goosenecks: the 15 cm MZH 3015 (6"), the 40 cm MZH 3040
(15.75") and the dual flex 40 cm MZH 3042 (15.75"), all designed to maintain
proper capsule placement. Each system requires 12-48 volt phantom power.
All contact points are gold plated and corrosion resistant. All components have
anti-reflective matte black surfaces.
ME36
MZC30
MZH30
ME 36
Polar Pattern Frequency Response Graph
Microphones | Installed Sound
Kit Includes:
ME 36 Capsule
MZC 30, MZH 30 Ceiling Hanger
i30H-L
Technical Data
Acoustic operating principle Pressure gradient transducer/
interference tube transducer
Pick-up pattern Super-cardioid/lobar
Frequency response 40–20,000 Hz
Sensitivity (free field, no load) @1kHz 18 mV/Pa
Electrical impedance 50 Ω
Min. terminating impedance 1 KΩ
Equivalent noise level 26 dB-A
37 dB-CCIR
Power supply P 12–P 48
Dimensions .322" x 3.78" (8.178mm x 96.01mm)
Weight .6 oz
Connector XLR-3
[96.0mm]
3.78"
.39
[9.9mm]
"
Ø.33"
[8.4mm]
Ø.26"
[6.6mm]
Lobar patterned mini shotgun condenser microphone capsule.
Provides added “reach”in miking applications.
i30H-L
CBinder - MIcrophones.indd 19 11/11/08 2:23:15 PM

Sennheiser Electronic Corporation • 1 Enterprise Drive • Old Lyme, CT 06371
Architects Specifications
The hanging mic system shall be modular and facilitate integration of different polar-patterned capsules. It must utilize a condenser transducer element
operational with 48v phantom power and have a frequency response of 40 Hz–20,000 Hz. The transducer must have shotgun directional characteristics,
utilizing interference tube technology and also be small and streamlined, no longer than 96 mm (3.8") with a diameter no larger than 6.6 mm (.26").
The 9 meter (29.5") hanging cable must have a 1 mm thickness, be Kevlar reinforced, and terminate to a pre-amp housed XLR connector. The system
must maintain strict on axis positioning using a low mass wire hanger with a 2 mm (.08") thickness. The system must be a Sennheiser i30H-L.
Limited Product Warranty/Service
Sennheiser Electronic Corporation extends the following limited product warranty for Sennheiser products:
The warranty period for all covered Sennheiser products is two years from the date of purchase. Not covered by this warranty are accessories and other consumables;
for example, items of wear and tear, such as cables. During the warranty period, Sennheiser Electronic Corporation warrants that the Sennheiser equipment will be
free from defects in materials and workmanship used in making the product. Abnormal conditions, deliberate abuse and damage due to accidents, operator’s error, or
unauthorized service attempts are excluded from any warranty claims.
Under this warranty, Sennheiser Electronic Corporation will repair, or at its option, replace free of charge the covered defective Sennheiser product, provided it is returned
(postage paid, with proof of purchase from the original seller) to a Sennheiser Service Facility. Products should be returned in their original package, or otherwise suitably
protected to avoid shipping damage. Either product registration or a valid, dated proof of purchase is accepted to establish the warranty period. The Sennheiser Service
Department will be the sole authority to determine the validity of all warranty issues.
This Limited Product Warranty is Sennheiser Electronic Corporation’s only warranty, and the customer’s only remedy concerning Sennheiser products. All other rep-
resentations and warranties, express or implied, written or oral, including, but not limited to, any warranties of merchantability, fitness for a particular purpose, or
non-infringement, are expressly excluded. As a result, except as set forth in the previous paragraphs, the product is sold “as-is” and the customer is assuming the
entire risk as to the product’s suitability for his needs, its quality and its performance.
In no event will Sennheiser Electronic Corporation be liable for direct, indirect, special, incidental or consequential damages resulting from any defect in the product or
from its use, even if advised of the possibility of such damages.
i30H-L
.34"
[8.6mm]
.53"
[13.5mm]
3.13"
[79.5mm]
3.89"
[98.8mm]
1.78"
[45.2mm]
105º
Ø.04"
[1.0mm]
The MZH 30 is a lightweight (0.1 oz) hanger accessory designed
to interface with ME 34, ME 35 and ME 36 capsules. Its nearly
invisible 1.1 mm diameter black wire design is durable and
strictly maintains on-axis placement.
MZH 30
.98"
[24.9mm]
1.86"
[47.2mm]
4.23"
[107.4mm]
.97"
[24.6mm]
2.65"
[67.3mm]
Ø.32"
[8.1mm] Ø.75"
[19.0mm]
MZC 30 The MZC 30 is a 9 m (28') cable for hanging applications of
the ME 34, ME 35 and ME 36 capsules and boundary layer
application of the ME 36 capsule. The sturdy 1 mm Kevlar
reinforced cable has a copper core and terminates to an XLR
connectorized preamp to accommodate P48 powering.
CBinder - MIcrophones.indd 20 11/11/08 2:23:17 PM